2010 CADILLAC ESCALADE ESV lock

Black plate (57,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Windshield Wiper Blade
Replacement Windshield wiper blades should be inspected for wear
or cracking. See Scheduled Maintenance on page 8 ‑ 3 .
Replacement blades come in different types and are
removed in different ways. To replace the wiper blade
assembly:
1. Pull the windshield wiper arm connector away from
the windshield.
2. Squeeze the grooved areas on each side of the
blade, and turn the blade assembly away from the
arm connector. 3. Install the new blade onto the arm connector and
make sure the grooved areas are fully set in the
locked position.
For the proper type and size, see Maintenance
Replacement Parts on page 8 ‑ 12 .
7-57

Black plate (58,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Backglass Wiper Blade Replacement 1. Lift the wiper blade assembly up and out of the
park rest position.
2. Pull the wiper blade assembly away from the
backglass. The backglass wiper blade will not lock
in a vertical position, so care should be used when
pulling it away from the vehicle.
3. Turn the wiper blade assembly, and pull it off of the
wiper arm. Hold the wiper arm in position and push
the blade away from the wiper arm. 4. Replace the wiper blade.
5. Return the wiper blade assembly to the park rest
position.
Tires Your new vehicle comes with high-quality tires
made by a leading tire manufacturer. If you ever
have questions about your tire warranty and
where to obtain service, see your vehicle
Warranty booklet for details. For additional
information refer to the tire manufacturer.
7-58

Black plate (71,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
5. Remove the valve cap from the valve cap stem.
Activate the TPMS sensor by increasing or
decreasing the tire's air pressure for five seconds,
or until a horn chirp sounds. The horn chirp, which
may take up to 30 seconds to sound, confirms that
the sensor identification code has been matched to
this tire and wheel position.
6. Proceed to the passenger side front tire, and
repeat the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat
the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the
procedure in Step 5. The horn sounds two times to
indicate the sensor identification code has been
matched to the driver side rear tire, and the TPMS
sensor matching process is no longer active. The
TIRE LEARNING ACTIVE message on the DIC
display screen goes off. 9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure
level as indicated on the Tire and Loading
Information label.
11. Put the valve caps back on the valve stems.
Tire Inspection and Rotation We recommend that you regularly inspect your
vehicle's tires, including the spare tire, for signs of
wear or damage. See When It Is Time for New
Tires
on page 7 ‑ 73 for more information.
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km). See Scheduled Maintenance
on page 8 ‑ 3 .
The purpose of a regular tire rotation is to achieve
a uniform wear for all tires on the vehicle. This will
ensure that your vehicle continues to perform
most like it did when the tires were new.
7-71

Black plate (75,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
{ WARNING: If you use bias-ply tires on the vehicle, the
wheel rim flanges could develop cracks after
many miles of driving. A tire and/or wheel
could fail suddenly, causing a crash. Use
only radial-ply tires with the wheels on the
vehicle.If you must replace your vehicle's tires with those
that do not have a TPC Spec number, make sure
they are the same size, load range, speed rating,
and construction type (radial and bias ‐ belted tires) as
your vehicle's original tires.
Vehicles that have a tire pressure monitoring system
may give an inaccurate low ‐ pressure warning if
non ‐ TPC spec rated tires are installed on your vehicle.
Non ‐ TPC Spec rated tires may give a low ‐ pressure
warning that is higher or lower than the proper warning
level you would get with TPC Spec rated tires. See Tire
Pressure Monitor System on page 7 ‑ 67 .
Your vehicle's original equipment tires are listed on the
Tire and Loading Information Label. See Loading the
Vehicle on page 6 ‑ 32 , for more information about the
Tire and Loading Information Label and its location on
your vehicle. Different Size Tires and Wheels If you add wheels or tires that are a different size than
your original equipment wheels and tires, this could
affect the way your vehicle performs, including its
braking, ride and handling characteristics, stability, and
resistance to rollover. Additionally, if your vehicle has
electronic systems such as anti ‐ lock brakes, rollover
airbags, traction control, and electronic stability control,
the performance of these systems can be affected.
{ WARNING: If you add different sized wheels, your vehicle
may not provide an acceptable level of
performance and safety if tires not recommended
for those wheels are selected. You may increase
the chance that you will crash and suffer serious
injury. Only use GM specific wheel and tire
systems developed for your vehicle, and have
them properly installed by a GM certified
technician.
See Buying New Tires
on page 7 ‑ 73 and Accessories
and Modifications on page 7 ‑ 4 for additional
information.
7-75

Black plate (80,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Changing a Flat Tire If your vehicle is a Two-mode Hybrid, see the
Two-mode Hybrid manual for more information.
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on the hazard
warning flashers. See Hazard Warning Flashers on
page 4 ‑ 3 .
{ WARNING: Changing a tire can be dangerous. The vehicle
can slip off the jack and roll over or fall on you or
other people. You and they could be badly injured
or even killed. Find a level place to change your
tire. To help prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in P (Park).
(Continued)WARNING: (Continued) 3. Turn off the engine and do not restart while
the vehicle is raised.
4. Do not allow passengers to remain in the
vehicle.
To be even more certain the vehicle will not move,
you should put blocks at the front and rear of the
tire farthest away from the one being changed.
That would be the tire, on the other side, at the
opposite end of the vehicle.
When the vehicle has a flat tire (B), use the following
example as a guide to assist you in the placement of
wheel blocks (A).
7-80

Black plate (81,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
A. Wheel Block
B. Flat Tire
The following information explains how to use the jack
and change a tire. Removing the Spare Tire and Tools The equipment you will need is stored under the
storage tray, which is located on the driver's side trim
panel (over the rear wheelhouse).
Regular Wheelbase shown, Extended Wheelbase
similar.
1. Remove the tray to access the tools by pulling up
on the finger depression under the jack symbol.
7-81

Black plate (82,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
2. Remove the wing nut (B) used to retain the tool
bag by turning it counterclockwise.
3. Turn the knob (A) on the jack counterclockwise to
release the jack and wheel blocks from the
bracket.
4. Remove the wheel blocks and the wheel block
retainer by turning the wing nut (C)
counterclockwise. The tools you will be using include the following:
A. Jack
B. Wheel Blocks
C. Jack Handle D. Jack Handle
Extensions
E. Wheel Wrench
7-82

Black plate (83,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
To access the spare tire:
A. Hoist Assembly
B. Hoist Shaft
C. Hoist Shaft Access
Cover/Hole
D. Jack Handle
Extensions
E. Wheel Wrench
F. Hoist Cable G. Tire/Wheel Retainer
H. Spare Tire (Valve Stem
Pointed Down)
I. Hoist Shaft Access Hole
J. Hoist End of
Extension Tool
K. Spare Tire Lock 1. To reach the hoist shaft access cover (C), you will
first need to remove the hitch cover. Remove it by
turning the two fasteners located at the bottom of
the cover counterclockwise and then pull the cover
down and rotate towards you.
2. Open the hoist shaft access cover (C) on the
bumper to access the spare tire lock (K).
3. To remove the spare tire lock insert the ignition
key, turn it clockwise and then pull the lock out.
7-83