2010 CADILLAC DTS service reset

Using Cruise Control on Hills
How well your cruise control works on hills dependsupon the vehicle speed, load, and the steepness of thehills. When going up steep hills, you might have tostep on the accelerator pedal to maintain the vehicle’sspeed. When going downhill, you might have to brake orshift to a lower gear to keep the vehicle’s speeddown. Applying the brake or shifting into a lower gearends cruise control. If you need to apply the brakeor shift to a lower gear due to the grade of the downhillslope, you might not want to attempt to use thecruise control feature.
Ending Cruise Control
To turn off the cruise control, step lightly on the brakepedal, or press the cancel button on the steering wheel.
Erasing Speed Memory
The cruise control set speed memory is erased whenthe cruise control or the ignition is turned off.
Adaptive Cruise Control
For vehicles with this feature, be sure to read this entiresection before using it.
The system operates on a radio frequency subject toFederal Communications Commission (FCC) Rules andwith Industry Canada.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
Changes or modifications to this system by other thanan authorized service facility could void authorization touse this equipment.
Adaptive Cruise Control (ACC) is an enhancement totraditional cruise control. It allows you to keep cruisecontrol engaged in moderate traffic conditions withouthaving to constantly reset your cruise control.ACC uses radar to detect a vehicle directly ahead inyour path, within a distance of 100 m (330 ft), andoperates at speeds above 40 km/h (25 mph). When it isengaged by the driver, the system can apply limitedbraking or acceleration of the vehicle automatically tomaintain a selected follow distance to the vehicle ahead.Braking is limited to 2.45 m/sec2 (0.25 g’s) ofdeceleration, which is comparable to moderate
4-15

If the light comes on while driving, pull off the road andstop carefully.The pedal may be harder to push, orthe pedal may go closer to the floor. It may take longerto stop. If the light is still on, have the vehicle towedfor service. SeeTowing Your Vehicle on page 5-24.
{WARNING:
The brake system might not be working properly if
the brake system warning light is on. Driving with
the brake system warning light on can lead to a
crash. If the light is still on after the vehicle has
been pulled off the road and carefully stopped,
have the vehicle towed for service.
Antilock Brake System (ABS)
Warning Light
For vehicles with theAntilock Brake System(ABS), this light comes onbriefly when the engineis started.
If it does not, have the vehicle serviced by yourdealer/retailer. If the system is working normally theindicator light then goes off.
If the ABS light stays on, turn the ignition off. If the lightcomes on while driving, stop as soon as it is safelypossible and turn the ignition off. Then start the engineagain to reset the system. If the ABS light stays on,or comes on again while driving, the vehicle needsservice. If the regular brake system warning light is noton, the vehicle still has brakes, but not antilockbrakes. If the regular brake system warning light is alsoon, the vehicle does not have antilock brakes andthere is a problem with the regular brakes. SeeBrakeSystem Warning Light on page 4-52.
For vehicles with a Driver Information Center (DIC), seeDIC Warnings and Messages on page 4-67for allbrake related DIC messages.
4-53

SIDE BLIND ZONE ALERT
If your vehicle has the Side Blind Zone Alert (SBZA)system, this display allows the system to be turned on oroff. Once in this display, press the set/reset button toselect between ON or OFF. If you choose ON, thesystem will be turned on. If you choose OFF, the systemwill be turned off. When the SBZA system is turnedoff, the DIC will display the SIDE BLIND ZONE ALERTSYSTEM OFF message as a reminder that thesystem has been turned off. SeeDIC Warnings andMessages on page 4-67andSide Blind Zone Alert(SBZA) on page 3-43for more information.
FRONT TIRES or REAR TIRES
On vehicles with the Tire Pressure Monitor System(TPMS), the pressure for each tire can be viewed in theDIC. The tire pressure will be shown in either poundsper square inch (psi) or kilopascals (kPa). Pressthe vehicle information button until the DIC displaysFRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press thevehicle information button again until the DIC displaysREAR TIRES PSI (kPa) LEFT ## RIGHT ##.
If a low tire pressure condition is detected by thesystem while driving, a message advising you to addair to a specific tire will appear in the display. SeeInflation - Tire Pressure on page 6-54andDIC Warningsand Messages on page 4-67for more information.
If the tire pressure display shows dashes instead of avalue, there may be a problem with your vehicle. If thisconsistently occurs, see your dealer/retailer for service.
SPEED LIMIT: XXX MPH (SPEED LIMIT:
XXX Km/h) or ADVISORY: XXX MPH
(ADVISORY: XXX Km/h)
This display will show the speed limit or the advisedspeed as determined by the information on the map discin the navigation system. If there is no map disc inthe navigation system, this display will not be available.
The speed limit and speed advisory displays on theDIC are for reference only. There may be segments ofroad where speed data has not been captured ortimes where incorrect speed data, or no speed data, willbe displayed by the DIC due to the navigation systemnot correctly matching the vehicle’s position to the actualroad. Be aware of this and obey posted speed limitswherever you drive.
SPEED ALERT
This display will allow you to customize the speed alertwarning. You can choose to have no warning display,or to have it display at the limit, at 5 km/h (mph) over thelimit, or at 10 km/h (mph) over the limit. The DIC willtoggle between OFF, AT LIMIT, +5, +10 (Km/h or MPH).Press the reset button to make your selection.
4-66

AUTOMATIC LIGHT CONTROL ON
This message displays when the automatic headlampsare turned on. SeeExterior Lamps on page 4-25formore information.
BATTERY SAVER ACTIVE
This message displays when the system detects thatthe battery voltage is dropping beyond a reasonablelevel. The battery saver system starts reducing certainfeatures of the vehicle that you may be able to notice.At the point that the features are disabled, this messageis displayed. It means that the vehicle is trying tosave the charge in the battery.
Turn off all unnecessary accessories to allow the batteryto recharge.
The normal battery voltage range is 11.5 to 15.5 volts.You can monitor battery voltage on the DriverInformation Center (DIC) by pressing the trip/fuel buttonuntil BATTERY VOLTAGE is displayed.
CHANGE ENGINE OIL SOON
This message displays when service is required for yourvehicle. See your dealer/retailer. SeeEngine Oil onpage 6-13andScheduled Maintenance on page 7-3formore information.
When you reset the CHANGE ENGINE OIL SOONmessage by clearing it from the display, you still mustreset the engine oil life system separately. For moreinformation on resetting the engine oil life system, seeEngine Oil Life System on page 6-16.
CHECK TIRE PRESSURE or ADD AIR
TO TIRE
On vehicles with the Tire Pressure Monitor System(TPMS), this message displays when the pressure inone or more of the vehicle’s tires is low. This messagealso displays LEFT FRONT, RIGHT FRONT, LEFTREAR, or RIGHT REAR to indicate which tire needs tobe checked. The low tire pressure warning light willalso come on. SeeTire Pressure Light on page 4-56.If a tire pressure message appears on the DIC, stop assoon as you can. Have the tire pressures checkedand set to those shown on the Tire Loading Informationlabel. SeeTires on page 6-46,Loading the Vehicleon page 5-18, andInflation - Tire Pressure onpage 6-54. You can receive more than one tire pressuremessage at a time. To read the other messages thatmay have been sent at the same time, press theset/reset button. The DIC also shows the tire pressurevalues. SeeDIC Operation and Displays on page 4-62.
4-68

PARKING ASSIST OFF
If your vehicle has the Ultrasonic Front and RearParking Assist (UFRPA) system, after the vehicle isshifted out of P (Park), this message displays to remindthe driver that the UFRPA system has been turnedoff. Press the set/reset button to acknowledge thismessage and clear it from the DIC display. To turn theUFRPA system back on, see “PARKING ASSIST”underDIC Operation and Displays on page 4-62. SeeUltrasonic Front and Rear Parking Assist (UFRPA)on page 3-40for more information.
PASSENGER DOOR OPEN
This symbol appears withthis message.
This message displays when the passenger side frontdoor is not closed completely. Make sure that the door isclosed completely.
RADAR CRUISE NOT READY
This message displays when the Adaptive CruiseControl (ACC) system will not activate due to atemporary condition. Your vehicle does not requireservice. If this message appears when you attempt toactivate the system, continue driving for several minutesand then try activating the system again. SeeAdaptiveCruise Control on page 4-15for more information.
REMOTE KEY LEARNING ACTIVE
This message displays while you are matching aRemote Keyless Entry (RKE) transmitter to your vehicle.See “Matching Transmitter(s) to Your Vehicle” underRemote Keyless Entry (RKE) System Operationon page 3-4andDIC Operation and Displays onpage 4-62for more information.
REPLACE BATTERY IN REMOTE KEY
This message displays when the battery in the RemoteKeyless Entry (RKE) transmitter needs to be replaced.To replace the battery, see “Battery Replacement” underRemote Keyless Entry (RKE) System Operation onpage 3-4.
4-73

SERVICE STABILITRAK
Your vehicle may have a vehicle stability enhancementsystem called StabiliTrak®. SeeStabiliTrak®Systemon page 5-5.
This message displays if there has been a problemdetected with the StabiliTrak system.
If this message comes on while you are driving, pull offthe road as soon as possible and stop carefully. Tryresetting the system by turning the ignition off then backon. If this message still stays on or comes back onagain while you are driving, your vehicle needs service.Have the StabiliTrak system inspected by yourdealer/retailer as soon as possible.
SERVICE SUSPENSION SYS (System)
This message displays when the magnetic ridecontrol or automatic leveling control system is notoperating properly. Have your vehicle serviced by yourdealer/retailer.
SERVICE THEFT DETERRENT SYSTEM
This message displays when there is a problem withthe theft-deterrent system programmed in the key.A fault has been detected in the system which meansthat the system is disabled and it is not protectingthe vehicle. The vehicle usually restarts; however, youmay want to take the vehicle to your dealer/retailer
before turning off the engine. SeePASS-Key®III+Electronic Immobilizer Operation on page 3-21for moreinformation.
SERVICE TIRE MONITOR SYSTEM
On vehicles with the Tire Pressure Monitor System(TPMS), this message displays if a part on the TPMS isnot working properly. The tire pressure light alsoflashes and then remains on during the same ignitioncycle. SeeTire Pressure Light on page 4-56. Severalconditions may cause this message to appear. SeeTirePressure Monitor Operation on page 6-58for moreinformation. If the warning comes on and stays on, theremay be a problem with the TPMS, see yourdealer/retailer.
SERVICE TRACTION CONTROL
This message displays when there is a problem with theTraction Control System (TCS). When this messageis displayed, the system will not limit wheel spin. Adjustyour driving accordingly. See your dealer/retailer forservice. SeeTraction Control System (TCS) on page 5-6for more information.
SERVICE TRANSMISSION
This message displays when there is a problem with thevehicle’s transmission. Have your vehicle serviced byyour dealer/retailer.
4-76

Finding a Station
BAND:Press to switch between AM, FM, or XM™.The selection displays.
a(Tune):Turn to select radio stations.
©SEEK¨:Press the arrows to go to the next or to
the previous station and stay there.
To scan stations, press and hold either arrow forthree seconds until a beep sounds. The radio goes to astation, plays for a few seconds, then goes to thenext station. Press either arrow again to stop scanning.
The radio only seeks and scans stations with astrong signal that are in the selected band.
4(Information) (XM™ Satellite Radio Service,
MP3/WMA, and RDS Features):Press this button todisplay additional text information related to thecurrent FM-RDS or XM station, or MP3/WMA song. Achoice of additional information such as: Channel, Song,Artist, CAT (category) can display. Continue pressingthe information button to highlight the desired label,or press the pushbutton positioned under any one of thetabs and the information about that tab displays.
When information is not available, No Info displays.
Storing a Radio Station as a Favorite
Drivers are encouraged to set up their radio stationfavorites while the vehicle is in P (Park). Tune to favoritestations using the presets, favorites button, andsteering wheel controls, if the vehicle has this feature.SeeDefensive Driving on page 5-2.
FAV (Favorites):A maximum of 36 stations can beprogrammed as favorites using the six pushbuttonspositioned below the radio station frequency tabs andby using the radio favorites page button. Press theFAV button to go through up to six pages of favorites,each having six favorite stations available per page.Each page of favorites can contain any combination ofAM, FM, or XM stations. To store a station as afavorite:
1. Tune to the desired radio station.
2. Press the FAV button to display the page whereyou want the station stored.
3. Press and hold one of the six pushbuttons until abeep sounds. When that pushbutton is pressedand released, the station that was set, returns.
4. Repeat the steps for each pushbutton radio stationyou want stored as a favorite.
4-94

XM Radio Messages
XL (Explicit Language Channels):These channels, orany others, can be blocked at a customer’s request,by calling 1-800-852-XMXM (9696).
XM Updating:The encryption code in the receiver isbeing updated, and no action is required. This processshould take no longer than 30 seconds.
No XM Signal:The system is functioning correctly, butthe vehicle is in a location that is blocking the XM™signal. When the vehicle is moved into an open area, thesignal should return.
Loading XM:The audio system is acquiring andprocessing audio and text data. No action is needed.This message should disappear shortly.
Channel Off Air:This channel is not currently inservice. Tune in to another channel.
Channel Unauth:This channel is blocked or cannot bereceived with your XM Subscription package.
Channel Unavail:This previously assigned channel isno longer assigned. Tune to another station. If thisstation was one of the presets, choose another stationfor that preset button.
No Artist Info:No artist information is available at thistime on this channel. The system is working properly.
No Title Info:No song title information is availableat this time on this channel. The system is workingproperly.
No CAT Info:No category information is available atthis time on this channel. The system is workingproperly.
No Information:No text or informational messages areavailable at this time on this channel. The system isworking properly.
CAT Not Found:There are no channels available forthe selected category. The system is working properly.
XM Theftlocked:The XM receiver in the vehiclecould have previously been in another vehicle. Forsecurity purposes, XM receivers cannot be swappedbetween vehicles. If this message is received afterhaving the vehicle serviced, check with yourdealer/retailer.
XM Radio ID:If tuned to channel 0, this messagealternates with the XM™ Radio 8 digit radio ID label.This label is needed to activate the service.
Unknown:If this message is received when tuned tochannel 0, there could be a receiver fault. Consultwith your dealer/retailer.
4-107