2010 CADILLAC DTS cruise control

WARNING: (Continued)
•When weather limits visibility, such as when in
fog, rain, or snow conditions, Adaptive CruiseControl performance is limited. There may notbe enough distance to adapt to the changingtraffic conditions. Do not use cruise controlwhen visibility is low.
The ACCs are located on the steering wheel.
The cruise control buttons are located on left side of thesteering wheel.
](On):Press to turn the system on.
+ Res (Resume/Accelerate):Press to make thevehicle resume to a previously set speed or to increasethe set speed when ACC is already active.
Set–:Press to set the speed or to decrease the setspeed when ACC is already active.
[(Cancel):Press to cancel ACC.
+GAP (Increase Following Distance):Press toincrease the distance between your vehicle and othervehicles.
!GAP (Decrease Following Distance):Press todecrease the distance between your vehicle and othervehicles.
ACC will not work if the master cylinder brake fluid levelis low.
4-17

Engaging ACC With the Set Button
{WARNING:
If you leave your Adaptive Cruise Control switch
on when you are not using cruise, you might hit a
button and go into cruise when you do not want
to. You could be startled and even lose control.
Keep the Adaptive Cruise Control switch off until
you want to use cruise control.
The set speed is selected by the driver. This is thespeed your vehicle will travel if there is no vehicledetected in its path.
To set ACC, do the following:
1. Press the]button.
2. Get up to the speed desired.
3. Press in the SET– button and release it.
4. Take your foot off the accelerator pedal.
Once ACC is set, it may immediately apply the brakes ifit detects a vehicle ahead is too close or movingslower than your vehicle.
The on symbol is located on the display at the top of theinstrument panel to the right of the driver. When the onsymbol is lit on the display, it indicates that ACC is active.
A message on the DIC will also display when ACC isset. SeeDIC Warnings and Messages on page 4-67.
Keep in mind speed limits, surrounding traffic speeds,and weather conditions when adjusting your set speed.
If the vehicle is in ACC when the traction controlsystem begins to limit wheel spin, the ACC willautomatically disengage. SeeTraction Control System(TCS) on page 5-6andStabiliTrak®System onpage 5-5. When road conditions allow you to safely useit again, the ACC can be turned back on.
Increasing Set Speed While Using ACC
There are two ways to increase the set speed:
•Use the accelerator to get to the higher speed.
Press the SET– button and then release thebutton and the accelerator pedal. The vehicle willnow cruise at the higher speed.
•Press the +RES button. Hold it there until the
desired set speed is displayed on the DriverInformation Center (DIC), then release the switch.To increase the set speed in very small amounts,move the switch briefly to +RES. Each timethis is done, the set speed increasesby 1 km/h (1 mph).
4-18

Alerting the Driver
The ACC alert symbol islocated on the display atthe top of the instrumentpanel to the right ofthe driver.
The alert symbol flashes and a warning beep soundswhen driver action may be required. If ACC is engaged,the alert symbol will flash when:
•ACC cannot apply sufficient braking because you
are approaching a vehicle too rapidly.
•The vehicle speed drops below about 32 km/h
(20 mph).
•A temporary condition prohibits ACC from operating.
SeeDIC Warnings and Messages on page 4-67formore information.
•A malfunction is detected in the system. SeeDIC
Warnings and Messages on page 4-67for moreinformation.
SeeDefensive Driving on page 5-2.
{WARNING:
Adaptive Cruise Control has only limited braking
ability to slow your vehicle. In some cases,
Adaptive Cruise Control may not have time to slow
your vehicle enough to avoid a collision. Be ready
to take action and apply the brakes yourself. See
Defensive Driving on page 5-2.
Approaching and Following a Vehicle
The vehicle ahead symbolis located on the top of theinstrument panel to theright of the driver.
The vehicle ahead symbol only appears when a vehicleis detected in your path.
4-20

If this symbol does not appear, or disappears briefly,ACC will not respond to vehicles you may see ahead.
{WARNING:
When the Adaptive Cruise Control radar is blocked
by snow, ice, or dirt, it may not detect a vehicle
ahead. Adaptive Cruise Control may not have time
to slow your vehicle enough to avoid a collision.
Do not use Adaptive Cruise Control when the
radar is blocked by snow, ice, or dirt. Keep your
radar clean. See “Cleaning the System” later in
this section.
ACC automatically slows your vehicle down whenapproaching a slower moving vehicle. It then adjustsyour vehicle speed to follow the vehicle in front atthe selected follow distance. Your vehicle speedincreases or decreases to follow the vehicle in front ofyou, but will not exceed the set speed. It may applylimited braking, if necessary. When braking is active,your brake lights will come on. Braking may feelor sound different than if you were applying the brakesyourself. This is normal.
Stationary or Very Slow-Moving Objects
{WARNING:
Adaptive Cruise Control may not detect and react
to stationary or slow-moving vehicles or other
objects ahead of you. You could crash into an
object ahead of you. Do not use Adaptive Cruise
Control when approaching stationary or
slow-moving vehicles or other objects.
{WARNING:
Adaptive Cruise Control may not detect and react
to stationary or slow-moving vehicles or other
objects ahead of you. Your vehicle may accelerate
toward objects, such as a stopped vehicle that
suddenly appears after the lead vehicle changes
lanes. Your complete attention is always required
while driving and you should be ready to take
action and apply the brakes.
4-21

Low-Speed Deactivation
If your vehicle speed falls below 32 km/h (20 mph) whilefollowing a vehicle ahead, ACC will begin to disengage.The Driver Alert symbol will flash and the warningbeep will sound. The driver must take action sinceACC will not slow the vehicle to a stop.
Passing a Vehicle/ACC Override
To increase speed to pass a vehicle, use the acceleratorpedal. While you are doing this, the system will notautomatically apply the brakes. A message will appearon the DIC. SeeDIC Warnings and Messages onpage 4-67. Once you remove your foot from theaccelerator pedal, ACC will return to normal operationand be able to apply the brakes, if needed.
{WARNING:
If you rest your foot on the accelerator pedal, the
system will not automatically apply the brakes.
You could crash into a vehicle ahead of you. Do
not rest your foot on the accelerator pedal when
using Adaptive Cruise Control.
Curves in the Road
{WARNING:
Due to Adaptive Cruise Control limitations in
curves, it may respond to a vehicle in another
lane, or may not have time to react to a vehicle in
your lane. You could crash into a vehicle ahead of
you, or lose control of your vehicle. Give extra
attention in curves and be ready to use the brakes
if necessary. Select an appropriate speed while
driving in curves.
ACC may operate differently in a sharp curve. It mayreduce your vehicle speed if the curve is too sharp.
4-22

Highway Exit Ramps
{WARNING:
Adaptive Cruise Control may lose track of the
vehicle ahead and accelerate up to your set speed
while entering or on highway exit ramps. You
could be startled by this acceleration and even
lose control of the vehicle. Disengage Adaptive
Cruise Control before entering a highway exit
ramp. Do not use Adaptive Cruise Control while
entering or on exit ramps.
Other Vehicle Lane Changes
If another vehicle enters the same lane as you, ACC willnot detect the vehicle until it is completely in the lane.Be ready to take action and apply the brakes yourself.
Using ACC on Hills and When Towing a
Trailer
How well ACC will work on hills and when towing atrailer depends on your vehicle’s speed, vehicle load,traffic conditions and the steepness of the hills. Itmay not detect a vehicle in your lane while driving onhills. When going up steep hills, you may want touse the accelerator pedal to maintain your vehicle’sspeed. When going downhill, especially when towing atrailer, you may want to brake to keep your speeddown. Applying the brake disengages the system. Youmay choose not to use ACC on steep hills, especiallywhen towing a trailer.
Disengaging ACC
To turn off the system, apply the brake pedal, press thecancel button, or press the ACC button.
4-24

Erasing Set Speed Memory
Press the ACC button or turn the ignition off.
Other Messages
There are three additional messages that may appearon the DIC. They are SERVICE RADAR CRUISE,RADAR CRUISE NOT READY and CLEAN RADAR.These messages will appear to indicate a problem withthe ACC. SeeDIC Warnings and Messages onpage 4-67for more information.
Cleaning the System
The radar can become blocked by snow, ice, or dirt.If so, you may need to turn off the engine and clean thelens. Remember, do not use ACC in icy conditions,or when visibility is low, such as in fog, rain or snow.
The emblem/lens is located in the center of the grille.
To clean the emblem/lens, wipe the surface with asoft cloth. After cleaning the emblem/lens, try to engagethe ACC. If you are unable to do so, see yourdealer/retailer.
Exterior Lamps
The exterior lamps controlis located on the instrumentpanel to the left of thesteering wheel.
It controls the following systems:
•Headlamps
•Taillamps
•Parking Lamps
•License Plate Lamps
•Instrument Panel Lights
•Fog Lamps
The exterior lamps control has four positions:
O(Off):Turns off the exterior lamps except for
Daytime Running Lamps (DRL).
4-25

If the light comes on and stays on, it means that oil isnot flowing through the engine properly. The vehiclecould be low on oil and it might have some othersystem problem.
Security Light
For information regardingthis light and the vehicle’ssecurity system, seeContent Theft-Deterrent onpage 3-19.
Fog Lamp Light
The fog lamp light comeson when the fog lamps arein use.
The light goes out when the fog lamps are turned off.SeeFog Lamps on page 4-30for more information.
Lights On Reminder
This light comes onwhenever the parkinglamps are on.
SeeExterior Lamps on page 4-25for more information.
Cruise Control Light
This light comes onwhenever the cruisecontrol is set.
The light goes out when the cruise control is turned off.SeeCruise Control on page 4-12andAdaptiveCruise Control on page 4-15for more information.
4-60