2010 CADILLAC DTS ignition

Remote Vehicle Start
With this feature the engine can be started from outsideof the vehicle.
Starting the Vehicle
1. Aim the RKE transmitter at the vehicle.
2. PressQ.
3. Immediately after completing Step 2, press and
hold/until the turn signal lamps flash.
When the vehicle starts, the parking lamps will turn onand remain on as long as the engine is running. Thedoors will be locked and the climate control system maycome on.
The engine will continue to run for 10 minutes. Repeat thesteps for a 10-minute time extension. Remote start canbe extended only once.
Canceling a Remote Start
To cancel a remote start:
•Aim the RKE transmitter at the vehicle and press
and hold/until the parking lamps turn off.
•Turn on the hazard warning flashers.
•Turn the ignition switch on and then off.
SeeRemote Vehicle Start on page 3-7.
Door Locks
From the outside, unlock the door using either the keyor the RKE transmitter.
From the inside, use the power door lock switches ormanual lock knobs located at the top of the door panelnear the window.
1-5

Power Door Locks
On vehicles with power door locks, the switches arelocated on the front doors.
"(Unlock):Press to unlock the doors.
Q(Lock):Remove the key from the ignition and press
to lock the doors.
For more information, see:
•Door Locks on page 3-9.
•Power Door Locks on page 3-10.
•Remote Keyless Entry (RKE) System Operation on
page 3-4.
Trunk Release
In addition to the trunk release button on the RKE
transmitter, there is a remote releaseVbutton located
to the left of the steering wheel next to the instrumentpanel brightness control. Press to open the trunk.
SeeTrunk on page 3-12.
Windows
On vehicles with power windows, the switches are onthe driver door armrest. Each passenger door hasa switch that controls only that window.
Press the switch to lower the window. Pull the switch upto raise it.
For more information, seePower Windows onpage 3-15.
1-6

Power Lumbar Adjustment
The control is located on the outboard side of the seat.
Press the front or rear of the control to increase ordecrease lumbar support.
SeePower Lumbar on page 2-4.
Heated and Ventilated Seats
On vehicles with heated and ventilated seats, thecontrols are located on the front doors and the ignitionmust be on to use the feature.
z:Press to heat the seat and seatback.
+:Press to heat the seatback.
H:Press to cool the seat and seatback.
For more information seeHeated and Ventilated Seatson page 2-5.
Head Restraint Adjustment
The vehicle’s front seats have adjustable head restraintsin the outboard seating positions.
Do not drive until the head restraints for all occupantsare installed and adjusted properly.
For more information seeHead Restraints on page 2-2.
1-8

Interior Lighting
Courtesy Lamps
The courtesy lamps are located on the headliner abovethe rear seat. These lamps come on by turning theinstrument panel brightness knob fully clockwise or whenany door is opened and it is dark outside.
Reading Lamps
The reading lamps are located on the overhead consoleon the headliner and in the rear door opening. Theselamps come on automatically when any door is openedand it is dark outside.
For manual operation, press the button to turn them onor off.
If the reading lamps are left on, they automatically shutoff 10 minutes after the ignition has been turned off.
For more information, see:
•Instrument Panel Brightness on page 4-31.
•Entry Lighting on page 4-31.
•Parade Dimming on page 4-31.
•Footwell Lamps on page 4-32.
Exterior Lighting
This control is located onthe instrument panel, tothe left of the steeringwheel.
P:Turns off the exterior lamps, except Daytime
Running Lamps (DRL).
AUTO:Automatic operation of the headlamps at normalbrightness, other exterior lamps and IntelliBeam™.
;:Manual operation of the parking lamps and other
exterior lamps.
2:Manual operation of the headlamps and other
exterior lamps.
#:Press to turn on the fog lamps.
For more information, see:
•Exterior Lamps on page 4-25.
•Daytime Running Lamps (DRL) on page 4-29.
•Fog Lamps on page 4-30.
•Wiper Activated Headlamps on page 4-29.
1-12

Tire Sealant and Compressor Kit
This vehicle may come with a jack and spare tire or atire sealant and compressor kit. The kit can be usedto seal small punctures in the tread area of the tire.
SeeTire Sealant and Compressor Kit on page 6-71forcomplete operating information.
Engine Oil Life System
The engine oil life system calculates engine oil lifebased on vehicle use and displays a DIC message whenit is necessary to change the engine oil and filter. Theoil life system should be reset to 100% only following anoil change.
Resetting the Oil Life System
1. Turn the ignition to ON/RUN, with the engine off.
2. Press the DIC INFO button until OIL LIFEREMAINING displays.
3. Press and hold the DIC INFO RESET button until100% displays.
4. Turn the key to LOCK/OFF.
SeeEngine Oil Life System on page 6-16.
Driving for Better Fuel Economy
Driving habits can affect fuel mileage. Here are somedriving tips to get the best fuel economy possible.
•Avoid fast starts and accelerate smoothly.
•Brake gradually and avoid abrupt stops.
•Avoid idling the engine for long periods of time.
•When road and weather conditions are appropriate,
use cruise control, if equipped.
•Always follow posted speed limits or drive more
slowly when conditions require.
•Keep vehicle tires properly inflated.
•Combine several trips into a single trip.
•Replace the vehicle’s tires with the same TPC Spec
number molded into the tire’s sidewall near the size.
•Follow recommended scheduled maintenance.
1-22

Power Lumbar
The power lumbar controlsare located on the outboardside of the front seats.
Press the front or rear of the lumbar control to increaseor decrease support. Press the top or bottom of thecontrol to raise or lower the support mechanism.
Massaging Lumbar
On vehicles with thisfeature, the switch islocated on the outboardside of the front seatsbehind the lumbar switch.
Press the switch to turn the massaging lumbar featureon. The ignition must be on for this feature to work. Themassage cycle will run for up to 10 minutes. To stopmassage, press the massaging lumbar switch again orpress the power lumbar switch.
2-4

Heated and Ventilated Seats
On vehicles with heated and ventilated seats, theignition must be on to use the feature.
The buttons are located onthe front doors.
J(Heated Seat Cushion and Seatback):Press this
button to heat the seat cushion and seatback.
I(Heated Seatback):Press this button to heat the
seatback.
H(Ventilated Seat Cushion and Seatback):Press
this button to cool the seat cushion and seatback.
Press each button to turn on the desired feature. A lighton that button will display indicating which feature is on.
There are three temperature settings for each feature.A column of three lights next to the buttons will displaywhich setting the feature is in: high, medium or low.Three lights indicate the highest setting, two lightsindicate medium and one light indicates the lowestsetting.
When you press a button, the feature will turn on at thehighest setting. Each time you press the button, thefeature will decrease one temperature setting.
To turn the feature off, keep pressing the button untilthe display lights turn off.
If your vehicle has remote vehicle start and is startedusing the remote keyless entry transmitter, the frontheated seats will be turned on to the high setting if it iscold outside. See “Remote Vehicle Start” underRemote Keyless Entry (RKE) System Operation onpage 3-4. When the key is inserted into the ignition andthe ignition is turned on, the heated seat feature willturn off. To turn the heated seat feature back on, pressthe desired button.
Driver’s Side Buttonsshown
2-5

If you use the RKE transmitter to enter the vehicle andthe remote recall memory feature is on, automaticseat and mirror movement will occur. See “MEMORYSEAT RECALL” underDIC Vehicle Customizationon page 4-80for more information.
To stop recall movement of the memory feature at anytime, press one of the power seat controls, memorybuttons, power tilt wheel control, or power mirrorbuttons.
If something has blocked the driver seat and/or thesteering column while recalling a memory position, thedriver seat and/or the steering column recall maystop. If this happens remove the obstruction, then pressthe appropriate control for the area that is not recallingfor two seconds. Try recalling the memory position againby pressing the appropriate memory button. If thememory position is still not recalling, see yourdealer/retailer for service.
Easy Exit Recall
The control for this feature is located on the driver doorpanel between buttons 1 and 2.
With the vehicle in P (Park), the exit position can berecalled by pressing the exit button. You will heara single beep. The driver seat will move back, and if thevehicle has the power tilt wheel and telescopic steeringfeature, the power telescopic steering column willmove up and forward.
If the easy exit seat feature is on in the DIC, automaticseat and power telescopic steering column movementwill occur when the key is removed from the ignition.See “EASY EXIT RECALL” underDIC VehicleCustomization on page 4-80for more information.
Further programming for automatic seat and steeringwheel movement can be done using the DriverInformation Center (DIC). You can select or not selectthe following:
•The easy exit recall feature
•The memory seat recall feature
For programming information, seeDIC VehicleCustomization on page 4-80.
2-7