2010 CADILLAC DTS reset

The DIC buttons are located on the instrument panel tothe left of the steering wheel.
3:Press to scroll through the trip and fuel displays.
T:Press to scroll through the vehicle information
displays.
U:Press to customize the feature settings on your
vehicle. SeeDIC Vehicle Customization on page 4-80for more information.
V:Press to reset certain DIC features and to
acknowledge DIC warning messages and clear themfrom the DIC display.
yz:Press to scroll up and down the menu items.
For more information, seeDriver Information Center(DIC) on page 4-61.
Vehicle Customization
Some vehicle features can be programmed by using theDIC buttons on the instrument panel to the left of thesteering wheel. These features include:
•Language
•Door Lock and Unlock Settings
•Lighting
•Chime Volume
•Memory Settings
•Remote Start
SeeDIC Vehicle Customization on page 4-80.
1-19

Tire Sealant and Compressor Kit
This vehicle may come with a jack and spare tire or atire sealant and compressor kit. The kit can be usedto seal small punctures in the tread area of the tire.
SeeTire Sealant and Compressor Kit on page 6-71forcomplete operating information.
Engine Oil Life System
The engine oil life system calculates engine oil lifebased on vehicle use and displays a DIC message whenit is necessary to change the engine oil and filter. Theoil life system should be reset to 100% only following anoil change.
Resetting the Oil Life System
1. Turn the ignition to ON/RUN, with the engine off.
2. Press the DIC INFO button until OIL LIFEREMAINING displays.
3. Press and hold the DIC INFO RESET button until100% displays.
4. Turn the key to LOCK/OFF.
SeeEngine Oil Life System on page 6-16.
Driving for Better Fuel Economy
Driving habits can affect fuel mileage. Here are somedriving tips to get the best fuel economy possible.
•Avoid fast starts and accelerate smoothly.
•Brake gradually and avoid abrupt stops.
•Avoid idling the engine for long periods of time.
•When road and weather conditions are appropriate,
use cruise control, if equipped.
•Always follow posted speed limits or drive more
slowly when conditions require.
•Keep vehicle tires properly inflated.
•Combine several trips into a single trip.
•Replace the vehicle’s tires with the same TPC Spec
number molded into the tire’s sidewall near the size.
•Follow recommended scheduled maintenance.
1-22

Express-Down/Up Windows
Windows with the express feature allow the windows tobe raised and lowered all the way without holdingthe switch.
Press or pull the switch fully and release it to activatethe express feature.
The express mode can be canceled at any time bybriefly pressing or pulling the switch.
Express Window Anti-Pinch Feature
If any object is in the path of the window whenthe express-up is active, the window will stop at theobstruction and auto-reverse to a preset factory position.Weather conditions such as severe icing may alsocause the window to auto-reverse. The windowwill return to normal operation once the obstructionor condition is removed.
Express Window Anti-Pinch Override
{WARNING:
If express override is activated, the window will not
reverse automatically. You or others could be
injured and the window could be damaged. Before
you use express override, make sure that all people
and obstructions are clear of the window path.
In an emergency, the anti-pinch feature can beoverridden in a supervised mode. Hold the windowswitch all the way up to the second position. The windowwill rise for as long as the switch is held. Once theswitch is released, the express mode is re-activated.
In this mode, the window can still close on an object inits path. Use care when using the override mode.
3-16

Mirror Adjustment
1. Press (C) to unfold the mirrors out to the drivingposition.
2. Press (D) to fold the mirrors toward the vehicle.
Resetting the Power Foldaway Mirrors
Reset the power foldaway mirrors if:
•The mirrors are accidentally obstructed while
folding.
•They are accidentally manually folded/unfolded.
•The mirrors do not stay in the unfolded position.
•The mirrors vibrate at normal driving speeds.
Fold and unfold the mirrors one time using the mirrorcontrols to reset them to their normal position. Anoise may be heard during the resetting of the powerfoldaway mirrors. This sound is normal after a manualfolding operation.
Turn Signal Indicator (If Equipped)
The vehicle may have a turn signal indicator lamp thatis built into the mirror. The turn signal lamp flasheswith the use of the vehicle’s turn signal and hazardflashers.
Outside Automatic Dimming Mirror
If the vehicle has this feature, the driver side mirroradjusts for the glare of headlamps behind you.This feature is controlled by the on and off settings onthe automatic dimming rearview mirror.
Side Blind Zone Alert (SBZA)
If the vehicle has the Side Blind Zone Alert (SBZA)system, seeSide Blind Zone Alert (SBZA) on page 3-43for more information.
3-38

The system operates in the delay mode. If the system isleft on for long periods of time, occasional wipes mayoccur without any moisture on the windshield. Thisis normal and indicates that the Rainsense™systemis active.
The Rainsense™system is activated by turning thewiper control band to one of the five sensitivity levelswithin the delay area. The position closest to off isthe lowest sensitivity setting, level one. This allows morerain or snow to collect on the windshield betweenwipes. Turning the wiper band away from you to highersensitivity levels increases the sensitivity of thesystem and frequency of wipes. The highest sensitivitysetting, level five is closest to low. A single wipe willoccur each time you turn the wiper stalk to a highersensitivity level to indicate that the sensitivity level hasbeen increased.
Notice:Going through an automatic car wash withthe wipers on can damage them. Turn the wipersoff when going through an automatic car wash.
The MIST and wash cycle operates as normal and arenot affected by the Rainsense™function. The systemcan be overridden at any time by manually changing thewiper control to low or high speed.
Notice:Do not place stickers or other items on theexterior glass surface directly in front of the rainsensor.
Windshield Washer
{WARNING:
In freezing weather, do not use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
J(Washer Fluid):Press and release this paddle,
located at the top of the turn signal/multifunction lever, tospray washer fluid on the windshield. The wipers willclear the windshield and either stop or return tothe preset speed. For more washer cycles, press andhold the paddle.
4-11

The cruise control buttonsare located on left side ofthe steering wheel.
I(On):Turns on the cruise control system.
+ RES (Resume/Accelerate):Press to make thevehicle accelerate or resume to a previously set speed.
SET– (Set):Press to set the speed.
[(Cancel):Press to cancel cruise control.
Cruise control will not work if the parking brake is set, orif the master cylinder brake fluid level is low.
If the brakes are applied, the cruise control shuts off.
The cruise light on the instrument panel cluster comeson after the cruise control has been set to the desiredspeed.
1. PressI.
2. Get up to the desired speed.
3. Press the SET– button located on the steeringwheel and release it.
4. Take your foot off the accelerator.
Resuming a Set Speed
Suppose the cruise control is set at a desired speedand then the brakes are applied. This shuts off thecruise control. But it does not need to be reset.
Once the vehicle is traveling approximately 40 km/h(25 mph) or more, press the +RES (resume/accelerate)button to return to the desired preset speed. Thecruise light displays again.
The vehicle returns to and stays at the preset speed. Ifyou press and hold the +RES button, the vehicle speedincreases until the button is released or the brake isapplied. Do not hold in the +RES button, if you do notwant the vehicle speed to increase.
4-13

Using Cruise Control on Hills
How well your cruise control works on hills dependsupon the vehicle speed, load, and the steepness of thehills. When going up steep hills, you might have tostep on the accelerator pedal to maintain the vehicle’sspeed. When going downhill, you might have to brake orshift to a lower gear to keep the vehicle’s speeddown. Applying the brake or shifting into a lower gearends cruise control. If you need to apply the brakeor shift to a lower gear due to the grade of the downhillslope, you might not want to attempt to use thecruise control feature.
Ending Cruise Control
To turn off the cruise control, step lightly on the brakepedal, or press the cancel button on the steering wheel.
Erasing Speed Memory
The cruise control set speed memory is erased whenthe cruise control or the ignition is turned off.
Adaptive Cruise Control
For vehicles with this feature, be sure to read this entiresection before using it.
The system operates on a radio frequency subject toFederal Communications Commission (FCC) Rules andwith Industry Canada.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
Changes or modifications to this system by other thanan authorized service facility could void authorization touse this equipment.
Adaptive Cruise Control (ACC) is an enhancement totraditional cruise control. It allows you to keep cruisecontrol engaged in moderate traffic conditions withouthaving to constantly reset your cruise control.ACC uses radar to detect a vehicle directly ahead inyour path, within a distance of 100 m (330 ft), andoperates at speeds above 40 km/h (25 mph). When it isengaged by the driver, the system can apply limitedbraking or acceleration of the vehicle automatically tomaintain a selected follow distance to the vehicle ahead.Braking is limited to 2.45 m/sec2 (0.25 g’s) ofdeceleration, which is comparable to moderate
4-15

Your vehicle will not reach the set speed until thesystem determines there is not a vehicle in front of you.At that point, your vehicle speed will increase to theset speed.
Decreasing Set Speed While Using ACC
Press the SET– button until you reach the lower speeddesired, then release it.
To slow down in very small amounts, briefly press theSET– button. Each time this is done, the set speeddecreases by 1 km/h (1 mph) slower.
Resuming a Set Speed
Suppose the ACC is set at a desired speed and thenthe brakes are applied. This will turn off the ACC. But itdoes not need to be reset.
Once the vehicle speed reaches about 40 km/h (25 mph)or more, press the +RES button. ACC will be engagedwith the previously chosen set speed.
Selecting the Follow Distance (GAP)
When the system detects a slower moving vehicle, it willadjust your vehicle’s speed and maintain the followdistance (gap) you select.
Use the plus and minus buttons on the steering wheelto adjust the follow distance.
Press the plus button to increase the distance or theminus button to decrease the distance. The first buttonpress shows the current follow distance setting onthe DIC. The current follow distance setting willbe maintained until it is changed.
There are six follow distances to choose from. Thefollow distance selection ranges from near to far(one second to two seconds follow time). The distancemaintained for a selected follow distance will varybased on vehicle speed. The faster the vehicle speedthe further back your vehicle will follow. Considertraffic and weather conditions when selecting the followdistance. The range of selectable distances may notbe appropriate for all drivers and driving conditions.If you prefer to travel at a follow distance farther thanACC allows, disengage the system and drive manually.
4-19