2010 AUDI S8 lock

-Cleaning and protection pn,,._____ _ __,____ ____________ _
0 Note
• Never try to remove dirt, mud o r d ust if the s urface of the vehicle
is dry. Never use a dry cloth or sponge, s ince this could scratch your
veh icle's pai nt o r win dows.
• Never was h your car in bright sunlight . D rops of water act as
magnifyi ng lenses and may damage your p aint.
• When you was h yo ur car in the winter: if you rinse your vehicle w ith
a hose , be careful not to a im the stream of wate r d irect ly at locks, or
at doo r or hatch openings -they can freeze s hut.
• N ever use sponges des igned to remove insects, o r any kitchen
sco uring sponges or s imilar pro ducts. They can damage yo ur paint
fi ni sh.
• N ever use a dry cl oth o r sp on ge to clean t he he adlig hts. Only use
wet cloths or sponges to prevent scratches . It is best to use soapy
water .
• You shou ld remove debr is (s uch as insects) from the head light
lenses o n a regu lar b asis, for examp le w hen re fue ling your veh icle.
N ever clean the headlights w ith a dry clot h or sponge . Use a wet cloth
or sponge. It is best to use soapy water.
c£> For the sake of the environment
In the interest of the environment, the ve hicl e should on ly be washed
in spe cial wash bays .•
Washing your vehicle with a power washer
C le aning the exterior of y our car wit h a hi gh-pressur e
p ower washe r is s afe as long as you observe a few simple
r ul es .
- Before using t he power washer, make su re yo u have read
and und ers tood th e WARNI NGS =:::>
& in "General in for­
mation" o n
page 270. -
Always fo llow t he operat ing inst ructio ns for the power
washer .
- Make su re that t he jet o n th e sp ray hose produces a "fan
s ha ped spr ay".
- Do
not hold the spray nozz le too close to soft ma terials.
W hen cleaning the vehicle with a power washer always fo llow the
operat ing in str uctio ns. T his appli es p art icu larly to t he
operating
pressure
and the spraying distance . Maintain a suffic ient distance to
so ft ma ter ia ls s uch as rubbe r hoses an d so und/v ibration deaden ing
materials (part icular ly on the unde rside o f the engine hood) . Do not
use a jet wh ich sprays water in a
direct stream o r o ne that has a
rotating jet .
Water temperature sho uld not exceed 140
°F (60 °().
& WARNING
Never wash tires with a jet that sprays water in a direct stream .
This could cau se invisible damage to the tires and weaken them,
even if the spray i s from a relatively long distance and for a short
time . Damaged and weakened tires can fail and cause accidents
and personal injury.
0 Note
To avoid damaging your vehicle, always ma ke su re that there is suffi­
cien t dista nce between the spr ay head and sof t mate ria ls like r ubber
hoses, p lastic parts and sound-deadening mater ials. Never aim the
spr ay he ad at the s ame po int for a long t ime . This also ap plies to
cleaning headlights and pai nted b umpe rs. Remember : the close r the
noz zle is to the surfa ce of the mate rial, t he greate r the stress on the
material. •

____________________________________________ C_l_e _a_ n_ in--= g=-- a_n_ d_ p ,__r_o _t_ e_ c_ t _ io_ n __ ,n
Your authorized Audi dealer can provide cleaning products that have
bee n tested and approved for your veh icle. •
Care of interior
MMI display
- Clean the MMI display with a soft clean cloth and an LCD
cleaner .
The MMI display can be cleaned with a professionally available "LCD
cleaner". The cloth should be slightly dampened with the cleaning
fluid to clean the d isp lay .
0 Not e
To avoid scratching the MMI display, you should never clean it dry. •
MMI terminal
- First clean the MMI terminal with a brush to remove dust
from the housing.
- Then wipe the MMI terminal with a clean, soft, slightly
damp c loth .
The MMI te rmi nal shou ld be cleaned with a b rush first so that no di rt
is trapped between the buttons and the housing. We recommend
giving the MM I termina l a final wipe w ith a cloth moistened with
water and dish wash ing detergent .
0 Note
To prevent damage, make sure that no fluid ever gets into the MMI
terminal. •
Safety first
Aluminum trim
Use only neutral-pH products to remove spots and deposits from
al uminum surfaces. Ch rome care prod ucts and al kaline cleaners w ill
attack aluminum surfaces and can damage them over t ime .
& WARNING
Alw ay s re ad and heed all WARNING S and other information
~ page 2 70. •
Fabrics and fabric coverings
Fabrics and fabr ic coverings (e .g . seats, door trim panels, etc.) should
be clean ed at regular interva ls with a vacuum cl eaner . T his removes
surfa ce di rt pa rt icl es which co uld become embedded in the fabr ic
through use . Steam cleaners should not be used, because the steam
tends to push the d irt deeper into the f abric and lock it there.
Norm al clean ing
Genera lly, we recommend using a soft sponge or a li nt-free
microfiber cloth to the clean fabric. Brushes should on ly be used for
ca rpets and floor mats , since other fab ric surfaces could be ha rmed
by brushes.
No rma l sur face sta ins can be cleaned us ing a commercially avai lab le
foam cleaner. Spread the foam on the surface of the fabr ic with a soft
sponge and work it in gently . Do not saturate the fabric. Then pat the
foam dry using absorbent , dry cloths (e .g. microfiber cloth) and
vacuum it after it has dried comp letely.
Clean ing stains
Sta ins caused by beverages (e .g. coffee, fruit juice, etc.) can be
treated with a mild detergent solut ion. Apply the detergent solut ion
with a sponge . In the case of stubborn stains, a detergent paste can
be applied directly to the stai n and worked into the fabric . After­
wards, use copious amounts of clean water to remove the remaining .,.
Vehicle care Technical data

____________________________________________ C_l_e _a_ n_ i n--= g=--- a_n_ d----' p,__ r_o _t_ e_ c_ t_ i _o_ n __ _
consider if childre n, animals or other factors might prove to be partic­
ularly hard on the leathe r.
By contrast, leather types that are covered by a colored fin ish layer
are more durable . This has a positive effect on the leath er's resistance
to wear and so iling in daily use. On the othe r hand, the typical charac­
teristics of natura l leathe r are barely or not apparent . However, this
does not mean that the leathe r itself is of infer io r quality.
C are and handling
Because of the exclusive nature of the types of leather that Audi uses
and the ir unique p roperties (such as sensitivity to oils, grease, so iling,
etc.), yo u will need to be somewhat ca refu l with these leat he rs , a nd
a certain type of care is required. For example, dark clothing mate­
r ials ca n disco lor leather seats (especially if such clothi ng is d amp and
was not dyed correctly) . Dust and dirt particles in pores, folds, and
seams can have an abrasive effect and c an damage the le athe r
surface as well as weaken seams .
The leather s houl d be cleaned regularly as needed . After having been
used for a relatively long time, your leather sea ts w ill acquire a rich
aged finis h. This is a characteristic of natura l leather and a sign of
true quality.
I n order to maintain the value of this natural product over the life of
your vehicle, you sho uld fo llow the recommendations below :
0 Note
• To keep you r leather from b leaching out, do not allow it to be
exposed to bright sunl ight for long periods of time . If you have to
leave t he veh icle parked outside for long pe riods, cover the leather to
protect it from direct exposure to sunlig ht.
• Sharp objects on clothing, such as zippers, rivets or sha rp pieces
on belts can leave permanent scratches or scrape marks on the
s u rface of the leather.
Safety first
(I] Tips
• After each time you clean the leathe r and at regular inte rvals , u se
a leather preservative creme that contains UV-blockers and that
works into the leather. This creme will nou rish and mo istur ize the
leather, helping it to breathe and stay supp le. It also helps to build up
a p ro tect ive coa ting on the surfa ce.
• Clean the leather every 2 -3 months, and clean any areas that get
soiled.
• Remove fresh marks made by ballpoint pens, ink, lipstick, shoe
polish, etc. as soon as poss ible.
• Preserve the color of t he leather as needed by using a specia l
co lored leather ca re creme to touch up areas of uneven color .•
Ap plies to vehi cles : w it h nat ural leat her
Cleaning and caring for leather upholstery
and trim
Natural leather requires special care and attention.
Normal cleaning
- Clean so iled areas wit h a slightly mois tened cotton or
woolen cloth .
More stubborn dirt
-More stubborn d irt can be removed using a clot h satu­
rated w ith a mild soap solution (2 ta blespoons m ild liq ui d
soap) .
- Never allow the soap solution to saturate the leather, and
make certa in that no water soaks i nto the seams .
- Wipe off the soap solution w ith a soft, dry c loth. .,,
Vehicle care Technical data

____________________________________________ C_l_e _a_ n_ i n--= g=--- a_n_ d----' p,__ r_o _t_ e_ c_ t_ i _o_ n __ _
0 Note
• N ev er use che mical s olvents (e.g. lig hte r fl uid , turpen tine), waxe s,
sho e polish or sim ila r pr oducts on A lcantara ® surfaces.
• T o avo id damage, have s tubbor n sta ins removed by a co mmerc ia l
cleaning s pecialist .
• Do not use brushes, stiff spo nges or sim ilarly ab rasive cl ea ni ng
aids. •
Safety belts
Only well- maintain ed safe ty b elts wo rk re liably when
n ee ded.
- Kee p belts cle an.
- F or clea nin g, use a mil d soap and w ate r solution. Let belts
dry thor oug hly and aw ay fro m direct s unlig ht.
- D o not a llow i nertia re el sa fety b elt s t o re trac t bef ore the y
are c ompl ete ly dry .
- Che ck th e condi tio n of you r sa fety belts
regu larly.
H eav ily so iled safe ty be lts may not ret rac t proper ly.
& WARNING
Damaged safety belts can break in a crash.
• Anything that might damage your safety belts could mean
that you and your passengers would not be adequately protected
in an accident.
• Safety belt performance depends on correct installation. Never
remove belts from the vehicle to clean them .
• Do not use chemical cleaning agents , bleach or dyes. They have
corrosive properties which weaken the webbing.
Safety first
& WARNING (co ntinued )
• When cleaning your safety belts , inspect them for damage . If
you discover damage, see your Audi dealer .
• Always read and heed all WARNINGS and other information
~page 270. •
Engine compartment
Be es pec ially care ful w hen clean ing th e engine co mp art­
m en t.
Always switch off the ign ition before cleaning the engine~,&. .
Plenum panel
Remove leaves from the plenum pane l in front of the win dshi eld
under the eng ine hoo d. Thi s preven ts the wa ter d rain holes fro m
becoming blocked , and it prevents debris from enter ing t he veh icle
in ter ior thro ugh t he heat ing a nd ve ntilation ducts.
Corrosion protection
The e ng in e co mp artm ent a nd trans missio n have bee n co rros io n­
protected at the facto ry .
G ood ant i- corro sion t rea tmen t is very i mporta nt, pa rt icul arly in t he
wi nte r. If the ve hicle is freq uently d riven on sa lt treated roads, the
entire eng ine compartment and plenum pane l sho uld be tho rough ly
clea ned at the end of winter and retreated to preve nt salt damage. At
the same time, t he un derside of the vehi cle should be washed as well.
If the eng ine co mpartme nt is clean ed at any t ime wi th gre ase
remov ing so lutions
2
), or if you have the engine was hed, the anti­
cor rosion treat men t is almo st alw ays rem oved as well.
It is the refore
essential to have a long-last ing corrosion protection reapplied to all
s u rfaces, seams, jo ints and com ponents in the engine compartmen t.~
2> Us e on ly the co rrect clean ing so lut ions . Neve r use gaso line or diese l fue l.
Vehicle care Technical data

Fuel supply and filling your fuel tank
Blend of gasoline and MTBE
• Anti-knock index must be 87 AKI or higher.
• Blend must contain not more than 15% MTBE.
Seasonally adjusted gasoline
Many gasoline grades are blended to perform especially well fo r
winter or summer driving. During seasonal change-over, we suggest
that you fill up at busy gas stat ions where the seasonal adjustment is
more likely to be made in time.
0 Note
• Methano l fuels which do not meet these requirements may cause
corrosion and damage to plastic and rubber components in the fue l
system .
• Do not use fuels that fail to meet the specified criteria in this
chapter .
• If you are unab le to determine whether or not a particu lar fuel
blend meets the spec ifications, ask your serv ice station or its fuel
supplier.
• Do not use fuel for which the contents cannot be identified.
• Fuel system damage and performance problems resulting from
the use of fuels different from those specified are not the responsi­
bility of Aud i and are not covered under the New Vehicle or the Em is­
sion Control System Warranties.
• If you experience a loss of fuel economy or driveab ility and perfor­
mance problems due to the use of one of these fuel blends, we
recommend that you switch to unblended fuel.•
Gasoline additives
A major concern among many auto manufacturers is carbon deposit
build-up caused by the type of gasoline you use. Although gasoline grades differ from one manufacturer to another,
they have certain things
in common. All gaso line g rades contain
substances that can cause deposits to collect on v ital engine parts,
such as fuel injectors and intake valves. A lthough most gasoline
brands include additives to keep eng ine and fuel systems clean, they
are not equally effective.
Audi recommends using TOP TIER Detergent Gasoline. For more
information on TOP TIER Detergent Gasoline, please go to the officia l
webs ite (www.toptiergas.com).
After an extended period of using inadequate fuels, carbon deposit
build-ups can rob your engine of peak performance.
0 Note
Damage or malfunction due to poor fuel quality is not covered by the
Audi New Vehicle Limited Warranty. •
Fuel tank
Fuel filler neck
The fuel filler neck is located on the right rear side panel behind the
fuel filler flap .
If the power locking system should fail, you can still open the flap
manually -for detailed instructions see~
page 287.
You can find the fue l tank capacity of your vehicle in Technical Data
~page 360.
The label on the inside of the fuel filler flap tells you the correct fuel
for your ve hicle. For more information about fuel specifications, see
~page 283.
Your vehicle fuel tank has an on board refuel ling vapor recovery
system. This feature helps to prevent fuel vapors from escaping from
the tank and polluting the environment wh ile you refuel your veh icle . ..,_

In order to fill the tank properly while protecting the environment,
please follow this refueling procedure carefully.
& WARNING
Under normal operating conditions, never carry additional fuel
containers in your car. Gas canisters and other containers used to
transport fuel can be dangerous. Such containers, full or empty,
may leak and could cause a fire in a collision. If you must transport
fuel to use for your lawn mower, snow blower, etc., be very careful
and always observe local and state laws regarding the use, trans­
portation and storage of such fuel containers. Make certain the
container meets industry standards (ANSI /ASTM F852 -86).
0 Note
Never drive your vehicle until the fuel tank is completely empty . The
irregular supply of fuel can cause misfiring. Gasoline could enter the
exhaust system and damage the catalytic converter. •
Refuelling
The fuel filler flap is unlocked from a button in the
driver's door.
Fig . 235 Driver's
door: Unlock ing fuel
filler flap
Vehicle OP-eration
Fuel supply and filling your fuel tank
Fig. 236 Fuel cap
hooked on the opened
f uel filler flap
When adding fuel , the ignition and any cellular phones in the
vehicle must be switched
off.
Taking the fuel cap off
- To open the fuel filler flap, press the button~ fig. 235.
- Unscrew fuel filler cap counter-clockwise and hang it on
the fuel filler flap~ fig . 236.
Refuelling procedure
- Insert the fue l nozzle from the gasoline pump into the
fuel filler neck as far as it will go.
- Select a medium refuelling rate so that the nozzle
switches off automatically when the tank is full.
Putting the fuel cap back on
- After filling your tank, twist the fuel filler cap clockwise
until you hear a definite click .
- Close the fuel filler flap.
To avo id fuel spi lling or evaporating from the fuel tank always close
fuel filler cap properly and completely . An improperly closed fuel
filler cap may also cause the MIL lamp~
page 25 to come on. ._.
Vehicle care Do-it-yourselt service iTechnical data

Unlocking the fuel filler flap by hand
You can open the fuel filler flap by hand if the power
locking system should fail.
Fig . 237 Luggage
compartment: Right·
side storage area
Fig. 238 luggage
compartment: Erner·
gency opening of fuel
filler flap
-Rotate the two pins @to the vertical position to open the
storage area.=:> fig. 237 .
- Unclip the loop® and move it to position©=:> fig. 238.
- Pull the loop down to position © to unlock the fuel filler
flap. •
Vehicle OP-eration
Fuel supply and filling your fuel tank
Vehicle care Do-it-yourselt service iTechnical data

___________________________________________ C..:...._ h:....:e :....:c:..:. k.::..: i..:.. n .:..:g:!:....:: a....:. n..:.. d~ f:....:. i.:..ll :.:.i:....:n :.:g !....- __
Closing the engine hood
- Pull the hood down until the pressure from the struts is
reduced.
- Let the hood
drop down and latch in place. Do not try to
push it shut;
it may fail to engage=:> &.
& WARNING
A hood that is not completely latched could fly up and block your
view while driving.
• When you close the engine hood, check it to make sure the
safety catch has properly engaged. The hood should be flush with
the surrounding vehicle body parts.
• If you notice while driving that the hood is not secured prop­
erly, stop at once and close it. •
Working in the engine compartment
Be especially careful whenever you work in the engine
compartment.
Whenever you must perform any work in the engine compartment,
for example checking and filling different fluids, there is a risk of injury, burns and accidents. To prevent personal injury always
observe the following WARNINGS. The engine compartment of any
vehicle is a hazardous area=>& .
& WARNING
To help avoid injury, before you check anything under the hood:
• Turn off the engine.
• Remove the ignition key.
• Apply the parking brake.
Safety first
& WARNING (continued)
• Move selector lever to "P" (Park).
• Always let the engine cool down. Hot components will burn
skin on contact.
• To reduce the risk of being burned, never open the hood if you
see or hear steam or coolant escaping from the engine compart­
ment. Wait until no steam or coolant can be seen or heard before
carefully opening the hood.
• Keep children away from the engine compartment.
• Never spill fluids on hot engine components. They can cause a
fire. • Never touch the radiator fan. The auxiliary electric fan is
temperature controlled and can switch on suddenly.
• Never open the coolant reservoir cap when the engine is still
warm. The coolant system is pressurized and hot coolant could
spray out.
• Protect your face, hands and arm from steam or hot engine
coolant by placing a thick rag over the cap when you open the
coolant reservoir.
• If work on the fuel system or the electrical system is necessary:
- Always disconnect the battery.
- Never smoke or work near heaters or open flames. Fluids in
the engine compartment could start a fire.
- Keep an approved fire extinguisher immediately available.
• To avoid electrical shock and personal injury while the engine is
running or being started, never touch:
-Ignition cables
- Other components of the high voltage electronic ignition
system.
• If you must perform a check or repair with the engine running:
- First, fully apply the parking brake, move selector lever to
"P" (Park). .,
Vehicle care Technical data