2010 AUDI A5 COUPE warning

& WARNING
• Do not leave children unattended in the vehicle, especially with
access to vehicle keys. Unsupervised use of the keys can result in
starting of the engine and use of vehicle systems such as power
windows, etc. which could result in serious injury.
• Remember -you can still open or close the power windows for
about ten minutes after the ignition is switched off. Only when
either of the doors are opened are the power windows switched
off.
• Be careful when closing the windows . Check to see that no one
is in the way, or serious injury could result!
• Always remove the ignition key whenever you leave your
vehicle.
• If you lock your vehicle from the outside, no one, especially chil­
dren, should remain in the vehicle.
• Do not stick anything on the windows or the windshield that
may interfere with the driver's field of vision.
[ i) Tips
• When you open the doors, the windows automatically lower
about 10 mm .
• Afte r the ignition has been switched off , the windows can still be
opened or closed for about 10 minutes . The window regulators are
not switched until the driver's or passenger 's door is opened. •
Controls and equip ­
ment
Opening and closing
Convenience opening /closing
The windows and the panoramic tilting sunroof can be
opened and closed with the mechanical key or the emer­
gency key.
Convenience opening feature
~ N 0
"' "' m
Fig. 46 Key turns for
opening and closing
- Use the emergency key or pull the mechanical key out of
the master key::} page
40.
- Insert the key into the lock of the driver's door.
Turn the key to position ::} fig. 46
@ until all the
windows have reached the desired position and the
panoramic tilting sunroof is tilted.
Convenience closing feature
-Use the emergency key or pull the mechanical key out of
the master key::} page
40.
Turn the key in the lock of the driver's door to the lock
position @ until the windows and the panoramic tilting
sunroof are closed::}& .
When the panoramic tilting sunroof is tilted/closed, the electric sun
shade * is also opened /closed. ._
I • •

Opening and closing
& WARNING
• Never close the windows and thepanoramic tilting sunroof
inattentively and without checking -there is risk of injury.
• You must always watch when the windows are being raised so
that no one can be trapped. If you release the key, the closing
action is immediately canceled.
• Always read and heed WARNING~
& in "General description"
on
page 41 . •
Correcting window regulator malfunction
After disconnecting the vehicle battery, the one-touch up
and down feature must be activated again.
- Pull and hold the power window switch until the window
is completely closed.
- Release the switch.
- Pull the switch again for one second. The automatic closing/opening is now reactivated. •
Valet parking
Through the "valet parking" feature the luggage compart­
ment of your vehicle is secured from unauthorized access
during the valet parking service.
Fig . 47 Valet parking
button
With "valet parking" activated, the rear lid cannot be
opened.
- Take the mechanical key out of the master key=>
page 40.
- Open the glove box=> page 89 and activate => fig. 47 the
"valet parking" feature by pressing the [VALET] button.
The indicator light in t he switch illuminates.
- Close the glove box and lock it with the mechanical key.
- Lock both rear seat backs with the mechanical key
=> page 82.
-Lock the luggage compartment pass -through with the
mechanical key=>
page 82.
-Leave the master key with the service personnel for
parking and keep the mechanical key with you.
When the "valet parking" feature is activated:

• the unlocking button for the rear lid~ in the driver's door is
inactive
• the button
~ on the master key is inactive
• the opening hand le in the rear lid is inactive.
T he vehic le can be driven and locked and unlocked with the master
key. Access to the luggage compartment is blocked. •
Panoramic tilting sunroof
Tilting and closing
""' CT;B ,;;.
;i N 0 ,;
"' CX)
Fig. 4 8 Sec tio n of
he adlin er: Sw itch fo r
pa noram ic til ting
s u nro of
To tilt the panoramic t ilting sunroof, press the switc h
brie fly.
To close the panoramic tilting sunroof, pu ll the sw itch
brie fly.
To set an intermediate position, press/pull the switch until the roof reaches the desired position.
After the ignition is switched off, you can sti ll operate the Panorama
for about 10 minutes . As soon as the driver's or passenger's door is
opened, the switch is inoperative.
Con tro ls and eq uip­
ment
Op ening and clo sing
S un blind
The sun b lind can be opened and closed manually in any position .
& WARNING
Pay careful attention when clo sing the panoramic tilting sunroof -
other wise seriou s injury could re sult! For t his r easo n, a lwa ys
remove the ignition key when leaving the vehi cle.
• Never le ave children or per sons requiring a ssist ance alone in
the v ehicle , e spe cially when they cou ld acce ss the vehi cle ke ys.
Un supervised use of the ke ys c an re sult in the engine being
s ta rted or use of vehicle system s such as the pow er windows, etc.
whi ch co uld r esult in serio us injur y. The door s could b e locked
with th e re m ote ke y, del aying h elp in an em ergency .
• The panor ami c tilting sunro of w ill continue to operate until the
igniti on ke y has been r em oved and one of th e front d oors ha s been
o pened .
0 Note
Always close your panoramic tilting sunroof when leaving your
vehicle . Sudden rain can cause damage to the interior equipment of
your vehicle, particularly the electronic equipment.
[ i ] Tip s
• Information on convenience opening/closing=> page 49. •
Vehicle care I I irechnical data

Clear vision
& WARNING
Automatic headlights are only intended to assist the driver. They do not relieve the driver of his responsibility to check the head­
lights and to turn them on manually according to the current light
and visibility conditions. For example, fog cannot be detected by
the light sensors. So always switch on the headlights under these
weather conditions and when driving in the dark
tD .
[ i ) Tips
• The light sensor* for headlight control is located in the rear view
mirror mount. You should therefore not apply any stickers to the
windshield in this area in order to prevent malfunctions or failures.
• The sensitivity level for the light sensor* set at the factory can be
changed in the MMI* menu ~
page 55 in the automatic driving
lights function.
• When you remove your key from the ignition while the vehicle's
lights are turned on, a buzzer sounds as long as the driver's door is
open.
• Please obey all laws when using the lighting systems described
here.
• The coming home/leaving home function* is available only with
the switch in the AUTO position. •
Fog lights
Fig. 52 Fog light
switch
To turn on the fog lights }D, press button (D => fig. 52.
- To turn on the rear fog lights
Ot press button @.
Fog lights
The side marker lights or low beams must be switched on. When the
fog lights are switched on, the green check light at the edge of the
switch comes on.
If automatic driving light control AUTO is activated, the low beams
are switched on when the fog lights are turned on.
Rear fog lights
Low beams or side marker lights with fog lights must be turned on.
When the rear fog lights are turned on, the yellow check light at the
edge of the switch comes on.
0 Note
The rear fog lights should only be turned on in accordance with
traffic regulation, as the lights are bright for following traffic. •

Adjusting exterior lighting
The functions are selected in the radio or MM/*.
Fig. 53 MMI Display:
Exterior l ighting
-Select: Function button [CAR]> Exterior lighting .
Coming home*
The coming home function ensures that after
turning off the igni ­
tion and opening the driver's door
the vehicle periphery is illumi ­
nated in the dark. In addition, the front fog lights, the tail lights and
the license plate light are turned on. The power-on time can be set
for a period from
O (off) to 30 or 60 seconds.
Leaving home*
The leaving home functions ensures that
when unlocking, the
vehicle periphery is illuminated in the dark. In addition, the front fog
lights, the tail lights and the license plate light are turned on. This
function can be turned on and off.
Auto headlights*
When the light switch is in the AUTO~
page 53 position, the switch­
on point of the lights can be changed in the automatic driving light
function.
Controls and equip ­
ment
Clear vision
Daytime running lights
The daytime running lights can be turned on or off using this func ­
tion. If the function is active, the daytime running lights are turned
on automatically when the ignition is switched on.
[ i] Tips
The coming home/leaving home function * is available only with the
switch in the AUTO position . •
Daytime running lights
When you turn on the ignition the daytime running lights
will come on automatically .
USA models
The daytime running lights are activated when the light switch
~ page 53, fig. 51 is in the O position or the AUTO position (only in
daylight conditions). The daytime running lights function can be
turned on and off in the radio or
MMI* menu Exterior lighting
~ page 55.
Canada models
The daytime running lights are activated when the light switch
~ page 53, fig. 51 is in the O position, ooo: position or the AUTO posi­
tion (only in daylight conditions). The daytime running lights func­
tion cannot be turned off.
& WARNING
Never use daytime running lights to see where you are going. They
are not bright enough and will not let you see far enough ahead for
safety, especially at dusk or when it is dark. Be aware of changes
in outside light conditions when you are driving and respond by
switching on your low beams
io. ~
I • •

Clear vision
0 Note
Always be aware of changes in outside light conditions while you
are driving. Respond in time to fading daylight by turning the light
switch to position
gO (or "AUTO") to turn on your headlights. •
Instrument lighting
The basic brightness of the illumination for the instru ­
ments, the center console and the display can be
adjusted.
Press the knob to release it.
Fig. 54 Instrument
lighting
- Rotating the knob to the right"+" will increase the basic
brightness when it is dark.
Rotating the knob to the left" -" will decrease the basic
brightness when it is dark.
- Pressing the knob will prevent unintentiona l changes.
0 Note
The instrument cluster and center console illumination (gauges and
needles) comes on when you switch on the ignition and the
vehicle headlights are off
.
Be aware of the following difference between
models built to US or Canadian specifications:
• USA models: illumination of the instrument cluster (gauges and
needles), dash and center console around the gearshift lever is
controlled by a light sensor located in the instrument panel. The
instrument panel illumination will automatically become dimmer
as the daylight fades away and eventually will go out completely
when outside light is very low. This is to remind you, the driver, to
switch on the headlights before it gets too dark.
• Canada models: instrument panel illumination will stay bright
regardless of the intensity of ambient light . Always be aware of
changes in outside light conditions while you are driving. Respond
in time to fading daylight by turning the light switch to position
gD
(or "AUTO" if your car is equipped with this feature) to turn on your
headlights. •
Applies to vehicles : w ith xenon head ligh ts
Xenon headlights
After starting the engine, the xenon headlights are automatically
adjusted to the load and angle of the vehicle (for example, during
acceleration and braking!. This prevents oncoming traffic from
experiencing unnecessary headlight glare from your xenon head­
lights.
If the system is not operating properly, a warning symbol in the
Auto-Check Control is displayed
:::::> page 36. •

[ i J Tips
• Pressing the button l~•~ l seve ral times consecutively can tr igger
the over load protection . The sun shade can only be
extended/re tracted again af ter a brief waiting period.
• The rea r window sun shade only functions when the vehicle inte ­
rio r is wa rmer than 23°F (-5°Cl. •
Wiper and washer system
Switching on the windshield wipers
Fig. 6 3 Win dshield
w iper l ever
M ove the windshield w iper lever to the c orresp onding position :
@-Windshie ld w iper off
G) -Interva l mode. To extend/shorten the wiper inte rvals, move the
sw itc h @ to the lef t/right. In vehic les wi th a rain sensor*, the w ind­
shield wipers are activated automatically starting at a speed of
2 mph (4 km/h). The higher the sensitivity of t he rain senso r* is set
(switch @to the right), the earlier the windshield wipers react to
moisture on the windshie ld.
@ -Slow wipi ng
© -Fast wiping
Con tro ls and eq uip­
ment
Clear vision
© -Single wipe
© -C lean the windshie ld. To eliminate wate r droplets, the wind­
shie ld wiper performs one afterwipe operation after several
seconds whi le d riving. You can switch this function off by moving
the lever to pos ition © within 10 seconds o f the afterwipe opera ­
tion. The afterwipe function is reactivated the next time the ignition
is sw itched on.
Cleaning the headlights *. The headlight washer system * only func ­
tions when the light is switched on . The headlights are automati ­
ca lly c leaned the first time and every fifth time the lever is moved to
pos ition
® · They are also cleaned every time you hold the lever in
pos ition © for longer than 2 seconds.
& WARNING
• The rain sen sor is only intended to a ssi st the driver . The driver
is still responsible for manually swit ching the wiper s on according
to the visibility conditions .
• The windshield may not be treated with water -repelling wind ­
s hield coating agents . Unfavorab le conditions , such as wetnes s,
darkness , low sun , can result in increased glare . Wiper bl ade
c hatter is also po ssible .
• Properly functioning windshield w iper blades are required for a
clear view and safe driving
~ page 63 , "Installing new wiper
blades ".
0 Note
• I n the case of frost, check whether the windshie ld wiper blades
are frozen to the windshield . Switching on the windshield wipers
ca n damage the wiper b lades !
• P rior to using a car wash, the windshield wiper system must be
switched off (lever in posi tion 0). This prevents un intentiona l
switching on and damage to the windshield wiper system. .,.
Vehicle care I I irechnical data

• The service position automatical ly switches to Off when you
opera te the windshie ld w iper lever, or speed exceeds 3 mph (6
km/h). •
Installing nevv wiper blades
Wiper bl ades in good c on dition help keep the win dshield
clear.
Removing th e wiper blade
Fig. 6 6 Rem oving t he
w ip er bl ad e
- Bring the windshield wipers to the service posi tion
=> page 62.
- Lift the windsh ield wiper arm up from the w indshie ld.
- Press the locking knob
G) => fig. 66 o n the wiper blade.
H old t he wiper b lade firm ly.
- Remove the wip er b lade in the d irect ion o f th e arrow.
Attaching the wip er blad e
-Install the new wiper blade i n the retainer on the wiper
arm
0 u ntil you hear it click into place on the wiper a rm.
- Place the w iper a rm back on t he windsh ield.
Controls and equip ­
ment
Cl ea r vision
& WARNING
• Cle an your w ip er blade s re gularly w ith a w ind shield was her
s olut ion to prevent streak ing . If the w iper bl ade s are very d irt y, for
ex am ple wi th in sects, c arefull y cl ean th e wiper blad es with a
sponge or a soft brush .
• For yo ur safety , you should repla ce the wiper b lade s o nce or
twice a year. See your authori zed Audi dealer for replacem ent
bl ade s.
0 Note
• The windshield wiper blades must only be replaced when in the
service position ~
page 62! Otherwise, you risk damaging the paint
on the hood or the windshie ld w iper motor.
• To prevent damage to the wiper system, always loosen blades
which are frozen to the windshield before operating wipers .
• To prevent damage to wiper blades, do not use gasoline, kero­
sene , paint thinner, or o ther so lven ts on or near the wiper blades.
• To prevent damage to the wiper arms or other components, do
not attempt to move the wipers by hand .
[ i ] Tip s
Commercial hot waxes applied by automatic car washes affect the
how easily the g lass surface can be c leaned .•
Mirrors
Manual glare-dimming
Standard s etting
- Move the sma ll leve r (located on the bottom edge of t he
m irror) to the front. _.
I • •