& WARNING (continued)
vehicle. Always drive at speeds which are suited to the road condi
tions -risk of crash. •
Energy management
Starting ability is optimized
Energy management controls the distribution of electrical
energy and thus optimizes the availability of electrical
energy for starting the engine .
If a vehicle with a conventional energy system is not driven for a
long period of time , the battery is discharged by idling current
consumers (e.g . immobilizer) . In certain circumstances it can result
in there being insufficient energy available to start the engine.
Intelligent energy management in your vehicle handles the distribu
tion of electrical energy. Starting ability is markedly improved and
the life of the battery is extended.
Basically, energy management consists of
battery diagnosis, idling
current management
and dynamic energy management .
Battery diagnosis
Battery diagnosis continuously determines the state of the battery.
Sensors determine battery voltage, battery current and battery
temperature. This determines the current state of charge and the
power of the battery.
Idling current management
Idling current management reduces energy consumption while the
vehicle is standing . With the ignition switched off, it controls the
energy supply to the various electrical components. Data from
battery diagnosis is considered.
Controls and equip ment Safety first Vehicle operation
Intelligent technology
Depending
on the battery's state of charge, individual consumers
are gradually turned off to prevent excessive discharge of the
battery and thus maintain starting capability.
Dynamic energy management
While the vehicle is being driven, dynamic energy management
distributes the energy generated according to the needs of the indi
vidual components. It regulates consumption, so that more elec
trical energy is not being used than is being generated and ensures
an optimal state of charge for the battery.
[ i] Tips
• But even energy management cannot negate the limits of
physics. Consider that the power and life of a battery are limited.
• If starting ability is threatened, you are informed by a warning
~ page 242, "Driver notification in the instrument cluster
display". •
What you should know
The highest priority is given to maintaining starting capa
bility.
The battery is severely taxed in short-distance driving, in city traffic
and during the cold time of year. Abundant electrical energy is
required, but only a little is generated. It is also critical if the engine
is not running and electrical components are turned on. In this
instance energy is being consumed but none is being generated.
It is in precisely these situations that you will notice energy manage
ment actively regulating the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period of several days or
weeks, electrical components are gradually cut back or switched off.
This reduces energy consumption and maintains starting capability
over a longer period.
Vehicle care Do-it-yourself service Technical data
llffl __ ln_ t _e_ ll-'"ig ...,_ e_ n_t _t_ e_ c_ h _ n_o _ l_o _,.g= y,_ __________________________________________ _
Take into consideration that when you unlock your vehicle, some
convenience functions, such as the remote key or power seat
adjustment, may not be available. The convenience functions will be
available again when you turn on the ignition and start the engine.
With the engine turned off
If you listen to the radio, for example, with the engine turned off or
use other MMI functions, the battery is being discharged .
If starting capability is jeopardized due to energy consumption, the
following warning appears in the MMI display :
Please start engine, otherwise system will switch off in
3 minutes.
The warning indicates that the system will be turned off automati
cally after 3 minutes. If you wish to continue using the functions,
you have to start the engine .
With the engine running
Although electrical energy is generated when the vehicle is being
driven, the battery can become discharged. This happens mostly
when little energy is being generated and a great deal consumed and the battery's state of charge is not optimal.
To bring the energy balance back into equilibrium, consumers
which require especially large amounts of energy are temporarily
cut back or switched off. Heating systems in particular require a
great deal of energy. If you notice, for example, that the heated
seats* or the heated rear window are not heating, they have been
temporarily cut back or switched off. These systems will be available
again as soon as the energy balance has been restored.
You will also notice that engine idle speed has been increased
slightly . This is normal and not a cause for concern. By increasing
engine idle speed the additional energy required is generated and
the battery is charged.
Driver not ification in the instrument cluster
d isplay
If battery power drops into the range where it can limit the ability of
the engine to start, this is shown in the instrument cluster display
with the following driver message:
'-' Low battery charge: battery will be charged while driving
This notification reminds you that the starting capability of the
engine may be limited. As soon as you start driving again, the
battery will be recharged and the notification will go out.
Driver notification appears and goes out again
If this driver notification appears after the ignition is turned on or
while driving and it goes out again after a while, the battery has
been adequately recharged.
Driver notification appears and does not go out again
If this driver notification appears after the ignition is turned on or
while driving and does not go out again, the battery's state of
charge is not in the optimal range . Starting ability is restricted . Have
the battery checked as soon as possible by an authorized Audi
dealer or qualified workshop. •
_____________________________________________ C_ l_ e _a_ n_ in_ g_a _ n_d_ p_ r_ o_ t _e_ c_t _io _ n __ lfll
•
& WA RNIN G (continu ed )
• Do not apply additi onal undercoating or ru stproofing on or
ne ar the exhau st manifold , ex haust p ipe s, cat alytic con verter or
heat shields . While driving, the s ub stan ce used for under coating
c ould overhe at and cau se a fire.
• Alway s read a nd heed all WARNINGS and other information
=> page 2 52 . •
Care of interior
A pp lies to veh ic le s: wit h MMI
MMI display
-Cle a n the MMI display with a soft c lean clo th and an LCD
cleane r.
The MM I disp lay can be c leaned with a professionally ava ilable "LCD
cleaner" . Th e cloth should be s lightly dampened with the c leaning
fluid to clean the display.
0 Note
To avoid scratching the MMI display, you should never c lean it dry .•
A pplies to veh ic les : wit h MMI
MMI terminal
- First clean t he MMI terminal with a brush to remove dust
f rom the housing .
- Th en wipe the MMI terminal with a clean, soft, s lig htly
d a mp cloth.
The MM I terminal should be c leaned with a brush first so that no
dirt is trapped between the buttons and the housing . We recom
mend giving the MMI terminal a fina l wipe with a c loth moistened
with wa ter and dish washing detergent .
0 Note
To prevent damage, make sure that no f luid ever gets into the MM I
terminal. •
Aluminum trim
Use only neutral -pH products to remove spo ts and deposits from
a luminum surfaces . Chrome care products and alka line cleaners
wi ll attack aluminum surfaces and can damage them over time .
& WARNING
Alway s re ad and heed all WARNING S and other information
=> page 252.•
Fabrics and fabric coverings
Fabrics and fabric coverings (e .g . seats, door trim pane ls, etc.l
shou ld be c leaned at regular intervals with a vacuum cleaner . T his
removes surface dirt partic les which could become embedded in
the fabric through use . Steam cleaners should not be used, because
the steam tends to push the dirt deeper into the fabric and lock it
there.
Normal cleaning
Generally, we recommend using a soft sponge or a lint -free
microfiber c loth to the clean fabric . Brushes should on ly be used for
carpets and floor mats , since other fabric surfaces could be harmed
by b rushes. .,,
Vehicle care I t •
Checking and filling -
-----------------=-----==-----...J
0 Note
Driving with an insufficient oil level is likely to cause severe damage
to the engine.
[ i] Tips
• The oil pressure warning display~ is not an indicator of the oil
level. Do not rely on it. Instead, check the oil level in your engine at
regular intervals, preferably each time you refuel, and always before
going on a long trip.
• If you have the impression your engine consumes excessive
amounts of oil, we recommend that you consult an authorized Audi
dealer to have the cause of your concern properly diagnosed. Keep
in mind that the accurate measurement of oil consumption requires
great care and may take some time. An authorized Audi dealer has
instructions about how to measure oil consumption accurately. •
Checking the engine oil level
Read oil level
Fig. 223 MMI Display;
Oil level indicator
Select: Function button [CARI> Oil level.
- Park your vehicle so that it is horizontally level. Shut
the engine off when it is at operating temperature.
Wait approx. two minutes. Read the oil level in the MMI* Display=> fig. 223. Add
engine oil if the bar of the oil level indicator is near "Min"
=>
page 275
Depending on the way the vehicle is driven and the operating condi
tions, oil consumption can be up to a 1/2 quart per 600 miles (0.5
liter per 1000 kml. Consumption may be higher within the first 3000
miles (5000 kml.
[ i] Tips
The oil level indicator in the MMI* Display is only an information
display. If the oil level is too low, a minimum oil warning appears in
the instrument cluster. Add oil
=> page 275. If the hood has been
opened, the current oil level is shown in the instrument cluster the
next time the ignition is switched on. •
Adding engine oil ~
Fig. 224 Engine
compartment; Oil filler
cap location
Before you check anything in the engine compartment,
always read and heed all WARNINGS=> & in "Working in
the engine compartment" on
page 271. .,,_
Vehicle care I I irechnical data
___ T_ ir_e_ s _ a_ n_d_ w_ h_ e_e _ l_s _________________________________________________ _
& WARNING
• Using incorrect or unm atched t ires and / or wheels o r improper
tire and wheel combinations can lead to lo ss of control , collision
and se rious per sonal injury .
• Always use tires , rim s and wheel bolts that meet the specifica
t ions of original f actory -installed tire s or other combinations that
have been spe cifically approved by the vehicle manufacturer .
• T ires age even if they are not being used and can fail suddenly ,
especially at high speeds . Tires that are more than 6 years old c an
only be used in an emergen cy and then with spec ial care and at
lower speeds .
• Never mount used tires on your vehi cle if you are not sure of
their "previou s history." Old used tires may have been damaged
e ven though the damage cannot be seen that can lead to sudden
tire failure and loss of vehicle control.
• All four wheels must be fitted w ith radial tires of the same type ,
size (rolling circumference ) and the same tread pattern . Driving
with different tires reduces veh icle handling and can lead to a loss
of control.
• If the spare t ire is not the same as the tires that are mounted
on the vehicle -for example with winter tires -only use the spare
tire for a short period of time and drive with e xtra care . Refit the
normal road wheel as soon as safely possible.
• Never drive faster than the ma ximum speed for which the tires
on your vehicle are rated because tires that are driven faster than
their rated speed can fail suddenly .
• Overloading tires cause heat build -up , sudden tire failure,
in cluding a blowout and sudden deflation and lo ss of control.
• Tempe rature grades apply to tires that are properly inflated and
not over or under inflated .
• For technical reasons it i s not always po ssible to use wheel s
from other veh icles - in some cases not even wheels from the
same vehicle model .
& WARNING (continued )
• If you install wheel trim discs on the vehicle wheels, make sure
that the air flow to the brakes is not blocked . Reduced airflow to
the brakes can them to overheat , increasing stopping distances
and causing a collision .
• Run flat tires may only be used on vehicles that were equipped
with them at the factory . The vehicle must have a cha ssis designed
for run flat tires and a fa ctory-installed tire pressure monitoring
system* that indicates a loss of tire pressure. Incorrect use of run
flat tires can lead to vehicle damage or acc idents . Check with an
authorized Audi dealer or tire specialist to see if your vehicle can
be equ ipped with run f lat tires . If run flat t ires are used , they must
be installed on all four wheels . Mixing tire types is not permitted.
0 Note
• For technical r eas ons, it is not gen erally possible t o us e the
whee l rims from other veh icles . ihis can ho ld true for whee ls of the
same veh ic le type.
• I f the spare tire is different from the tires that you have mounted
o n yo ur vehicl e (f or example wi nter tires or wide p rofile t ires), then
use the spare tire for a short period of time on ly and drive with extra
care . Rep lace the flat tire wi th the ti re m atchi ng t he o thers on you r
vehic le as soon as possib le.
• I f you should put diff ere nt w heels and tires o n your v ehicle (e. g.
winter wheels and tires), you must be certain that the wheels and
t ires are c ompatib le wi th the tire p ressu re monitoring system* .
Otherwise the system will register a malfunction and a fau lt
mes sage will be displayed . For more info rmation, contact your
author ized Aud i dea ler.
0 Note
• When insta lling new t ires, be care fu l not to damage the va lves o r
tire pressure mon itoring system* sensors. .,_
-~_T_ ir_e_ s_ a_ n_d _ w_ h_ e_e _l_s _________________________________________________ _
Fig. 235 Display:
System malfunction
Usin g the ABS senso rs, the tir e pressure monitor ing system
c o mp ares the tire t read ci rc um fere nc e a nd vibr atio n c harac te ristic s
o f the i ndividual ti res . If t he press ure decr eas es in one or mor e tires,
th is is ind ica te d in the i nstru me nt clust er w ith a wa rning symbol
fl
and a messa ge=> page 3 0 7, fig . 234. The driv er m essage i n th e
dis play goes out after
5 seconds. The driver message can be
d isp lay ed aga in by p ress ing the
!SE T] button. I f only one tir e is
affected, the disp lay wil l indicate its position .
Th e ti re pr essur e mo nitori ng system mu st b e rese t via ra dio or MM I*
each t ime the pressur es are adjusted (e.g. when sw itchi ng b etw een
p a rt ial an d fu ll lo ad pr essu re) or after changi ng or re pl acin g a tire
on your vehic le=>
pa ge 30 9. You can find t he recommended t ire
pressures for your vehic le on the label on driver's side B -pil lar
=>
p ag e 291 .
Tire tread circ umference and vibration characteristics can change
a nd ca use a tire pre ssur e warni ng i f:
• th e t ire pr essure in o ne or mor e tires is too low,
• t he tir e h as structur al d am age,
• the tire pressure was changed, whee ls rotated or replaced but
th e TP MS was not re set =>
page 30 9.
Warning symbols
\.) Loss of pressur e in at le ast one tire => & . C heck the t ire or tire s
and re place or repa ir if necessar y. T he indicato r light
1 in the instrument cluster also
ill uminates=>
page 1 2. C heck/correct th e
p res su res of a ll four tir es and re set TPMS via radio or MMI *.
~ (T ir e Pressure Monito rin g S ystem) Tire pressure! System
malfunction.
I f v a p pears a fter switch ing the i gnition on or w hile drivin g
=> fig. 235 and the indicator light,. in the instrument cluster blinks
f or approx im ately one min ute and then sta y s on , the re is a syste m
malfunct ion . S ee your authorize d Audi dealer as soon as possib le .
& WARNING
• If the tire pressure indicator appears in the instrument cluster
display, one or more of your tires is significantly under -inflated .
Reduce your speed immediately and avoid any hard steering or
braking maneuvers. Stop as soon as possible and check the tires
and their pressures . Inflate the tire pressure to the proper pressure
as indicated on the vehicle's tire pressure label
=> page 291.
Driving on a significantly under -inflated tire causes the tire to over
heat and can lead to tire failure . Under-inflation also is likely to
impair the vehicle's handling and stopping ability .
• The driver is responsible for maintaining the correct tire pres
sures . You must check the tire pressures regularly .
• Under certain conditions (such as a sporty driving style , winter
conditions or unpaved roads ), the pressure monitor indicator may
be delayed.
• Ask your authorized Audi dealer if run -flat tires may be used on
your vehicle. Your vehicle registration becomes invalid if you use
these tires when not permitted . Damage to your vehi cle or acci
dents could also result.
[ i ] Tips
• Th e tir e pr es sur e m oni tori ng syst em stops wor king whe n there
i s an ESP/A BS malfunction.
• U sing s now ch ai ns m ay r esu lt in a s ystem malf u ncti on . .,_
General information -
----------------
left door jamb. It shows the month and year of production and the
vehicle identification number of your vehicle (perforation) as well as
the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight
Rating (GAWR).
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with the Canadian
standard ICES-002. •
Applies to vehicles: with MMI
Identification Number in the MMI
Fig. 261 MMI display:
Vehicle ID number
(VIN)
You can also display the Vehicle Identification Number of
your vehicle in the MMI.
- Press the
I CAR) function button.
- Select
Vehicle ID number (VIN). The Vehicle ID number
(VIN)
menu appears =:> fig. 261. •
Controls and equip
ment Safety first Vehicle operation
Weights
Gross Vehicle Weight Rating
The Gross Vehicle
Weight Rating (GVWR), and the Gross Axle Weight
Rating (GAWR) for front and rear are listed on a sticker on the left
door jamb.
The Gross Vehicle Weight Rating includes the weight of the basic
vehicle plus full fuel tank, oil and coolant, plus maximum load,
which includes passenger weight (150 lbs./68 kg per designated
seating position) and luggage weight:::::,&.
Gross Axle Weight Rating
The Gross Axle Weight Rating is the maximum load that can be
applied at each axle of the vehicle:::::,.&,.
Vehicle capacity weight
The vehicle capacity weight (max. load) is listed either on the
driver's side B -pillar or inside the fuel filler flap.
Roof weight
The maximum permissible roof weight is 165 lbs. (75 kg). The roof
weight is made up of the weight of the roof rack system and the
weight of the object being transported:::::,
page 85, "Roof load".
& WARNING
• The actual Gross Axle Weight Rating at the front and rear axles
should not exceed the permissible weights, and their combination
must not exceed the Gross Vehicle Weight Rating.
• Exceeding permissible weight ratings can result in vehicle
damage, accidents and personal injury.
0 Note
• The vehicle capacity weight figures apply when the load is
distributed evenly in the vehicle (passengers and luggage) . When _,,
Vehicle care Do-it-yourself service Tec hn ica l da ta
llffl __ A_l.:. p _h_ a_ b_e _t _ic _ a_l _in _ d_e _x ____________________________________________ _
Care of exterior ... .. ... ... ... ... ... . 252
Cargo area
See Loading the luggage compartment ..
175
Cargo net .... .... ................... 79
Catalytic converter . . . . . . . . . . . . . . . . . . 244
Center armrest Adjusting ........................ 78
Storage compartment ........ .... . 78
Certification . . . . . . . . . . . . . . . . . . . . . . . 342
Changing a flat tire .. .... .... ....... 312
Changing a wheel ................... 312
Changing engine oi l ...... .... .... ... 276
Chassis Undercoating . . . . . . . . . . . . . . . . . . . . 258
Checking Engine coolant level .. ...... ...... 278
Checking tire pressure .... .... .... ... 293
Child restraint system anchors ........ 227
Child restraints Danger of using child restraints in the
front seat . . . . . . . . . . . . . . . . . . . . . . 190
Where can I get additional information
about child restraints and their use? ...
232
Child safety ................... .... . 213
Convertible locking retractor . . . . . . . 223
Important safety instructions for using
child safety seats .... .... ... .... 216
Important things to know when driving with chi ldren ................... 213
Installing a child restraint using the
LATCH system .................. 229 Lower
anchorages ... ...... ...... . 228
Mounting and releasing the anchorage hook .. .............. ....... ... 229
Tether anchors .. ...... .... .... .. 230
Tether straps ........ ....... ..... 230
Child safety seats ... ........... ..... 218
Booster seats .. ... .... ........ ... 221
Convertible chi ld seats ............ 219
Convertible locking retractor . ...... 223
Danger of using child restraints in the
front seat . . . . . . . . . . . . . . . . . . . . . . 190
How do I properly install a child safety
seat in my vehicle? ........ ...... 216
Infant seats ...... ........ ....... 218
Installing ....................... 223
LATCH system . . . . . . . . . . . . . . . . . . . 229
Safety instructions .... ...... ..... 216
Cigarette lighter ........ ....... ...... 87
Cleaning Alcantara® (synthetic suede) . ..... 262
Engine compartment ....... ... ... 263
Fabrics and fabric coverings ..... .. 259
Instrument panel ................. 260
Interior .. .... .... ... .. .... .... .. 259
Leather ......................... 261
MMI display ..................... 259
MM I termina l .. ... .... .... .... ... 259
Plastic and vinyl .. .. ......... ... . 256
Plastic parts . . . . . . . . . . . . . . . . . . . . . 260
Safety be lts ...... ....... ........ 263
Trim strips . ........... .... ...... 255
trim strips ... .. ........ .... ... ... 256
Cleaning and protection .. ........ ... 252
Clock ........ .... ...... ....... ...... 10 Coat hooks
. . . . . . . . . . . . . . . . . . . . . . . . . . 89
Co ld tire inflation pressure .... ....... 291
Compact spare tire .................. 311
See also Spare tire ........ ...... .. 311
Compass mirror . ...... .. .... .... .... 67
Comp liance ...... .... ....... .... ... 342
Consumer Information .... ... ... . 177, 339
Contacting NHTSA ... .... .... .... ... 177
Convenience closed ... ....... ........ 49
Convenience key ..................... 44
START ENGINE STOP button ... 110, 111
Starting engine .... ....... .... ... 110
Switching engine off .............. 111
Switching on ignition ............. 11
O
Unlocking and locking vehicle ... ... . 44
Convenience opening ...... ........... 49
Convertible child safety seats ...... ... 219
Convertible locking retractor Activating .. ....... .... ...... .... 225
Deactivating ..................... 226
Using to secure a child safety seat .. 223,
225
Coolant system ..................... 277
Cooling System Expansion tank .... ........... ... 278
Cornering light ...................... 57
Cruise contro l
Changing speed . ...... .... .... .. 116
Preselect speed .. ...... ..... .. ... 116
Switching off ... .. .... .... .... ... 116
Switching on ...... ........... ... 115
Warning/indicator lights ... .. ...... . 15
Cruising range ................... .... 23