2010 AUDI A5 CABRIOLET wheel bolt torque

Tires and wheels -______________________ Effll
be fitted ove r th e wheel bo lts . These a re available from a uthorized
Au di d eal er s.
& WARNING
Using the wrong snow chains for your vehicle or installing them
incorrectly can increase the risk of loss of control leading to
serious personal injury.
• Snow chains are available in different sizes . Always make sure
to follow the instructions provided by the snow chain manufac­
turer.
• When driving with snow chains never drive faster than the
speed permitted for your specific snow chains.
• Always observe local regulations.
0 Note
• Remove snow chains befor e driving on roads not covered w it h
snow to avoid dama gin g tir es and wearing t he snow chai ns dow n
unnece ssaril y.
• Snow chains, which come into direct contact with t he wheel rim,
can scratch o r damag e it. Ther efore, ma ke sure th at th e snow cha ins
are suitably covered. C hec k the pos it io n of the snow cha ins afte r
dr iv in g a few yar ds and correct if ne ce ssa ry . Fo llo w the i nstructions
from t he snow chain ma nufact urer w hen doing so.
[ i ] Tips
W here snow c hains are mandatory on certain roads, this no rmally
a lso a ppl ies to vehicl es wi th a ll w hee l dr ive . •
Safety first
Wheel bolts
Whe el bolts must alway s be tight en ed to th e corre ct
to rqu e.
T he design of wheel bolts is matche d to the fac to ry installed rims. If
differe nt rims ar e fitte d, the cor rec t wheel bolts with the r ight length
and co rrectly s haped bolt hea ds must be used. Th is ensures that
w heel s are fitted s ecur ely and that t he brak e sys te m fun ction s
correctly .
I n certai n circumstances, yo u may not use wheel bolts from a
different veh icle -even if it is th e sam e mode l~
page 345.
& WARNING
Improperly tightened or maintained wheel bolts can become
loose causing loss of control, a collision and serious personal
injury .
• Always keep the wheel bolts and the thread s in the wheel hubs
clean so the wheel bolts can turn easily and be properly tightened.
• Never grease or oil the wheel bolts and the threads in the wheel
hubs. They can become loose while driving if greased or oiled, even
if tightened to the specified torque.
• Only use wheel bolts that belong to the rim being installed.
• Never use different wheels bolts on your vehicle.
• Always maintain the correct tightening torque for the wheel
bolts to reduce the risk of a wheel loss. If the tightening torque of
the wheel bolts is too low , they can loosen and come out when the
vehicle is moving. If the tightening torque is too high, the wheel bolts and threads can be damaged and the wheel can become
loose .
0 Note
The sp eci fied tor qu e for th e wheel bolts i s 90 ft lb ( 120 Nm) wi th a
tole rance of ± 7,4 ft lb( ± 10 Nm). Torque wheel bo lts diagonally. .,_
Vehicle care Technical data

What do I do now? Ill ____________ ______;_ __ _
& WARNING (continued)
the ground, placing the Automatic Transmission in "P" (Park) will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and
firm. If necessary, use a sturdy board under the jack.
• After installing the inflatable spare tire, make sure that you
replace the flat tire/wheel in its storage area properly and tighten
the knurled retaining screw securely.
0 Note
If you are changing the wheel on a steep incline, use a rock or simi lar
object to block the opposite wheel to prevent the vehicle from
moving.
[I] Tips
Obey all laws. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Remove the decorative wheel cover*. For more details see
also =>
page 322, "Decorative wheel covers" .
2. Loosen the
wheel bolts=> page 323.
3. Locate the proper mounting point for the jack and align
the jack below that point=>
page 323.
4. Lift the car with the jack=> page 323.
5. Remove the wheel with the flat tire and then install the
spare tire=> page 325.
Safety first
6. Tighten all wheel bolts lightly.
7. Lower the vehicle with the jack .
8. Use the wheel bolt wrench and firmly tighten all wheel
bolts in a crisscross pattern=>
page 323.
9. Replace the decorative wheel cover*.
& WARNING
Always read and follow all WARNINGS and information~ & in
" Raising the vehicle" on
page 323 and ~ page 326. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wheel you replaced in the spare
wheel well.
- Replace the tools and the jack in their proper location.
- Check the
tire pressure of the spare tire as soon as
possible.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 90 ft lb (120 Nm).
- Have the flat tire
replaced as soon as possible.
[ i] Tips
• If you notice that the wheel bolts are corroded and difficu lt to turn
while changing a tire, they should be replaced before you check the
tightening torque. .,_
Vehicle care Do-it-yourself service Technical data

-What do I do now? .,,,.,__ ______________ _
• Drive at reduced speed until you have the tighten ing torques
checked. •
Applies to ve hicles: wit h deco rative whee l covers
Decorative wheel covers
The decorative wheel cove rs must be removed fi rst to
access the wheel bolts.
• •••
Removing
Fig. 237 Ch an g in g a
w heel: remo ving th e
wh eel cove r
- Insert the hook provided with the vehicle tool ki t in the
hole in the hub.
Pull off the
decorative wheel cover => fig. 2 3 7 . •
Applies to veh icles : w ith wheel bolts with caps
Wheels with wheel bolt caps
The caps must be removed first from the wheel bolts
before the bolts can be unscrewed .
Removing
Fig . 2 38 Ch an ging a
whe el: r emo ving the
wh eel bolt caps
-Push the plastic clip provided with the vehicle tool kit over
the wheel bolt cap until it engages .
- P ull on the
plastic clip to remove the cap=> fig. 238.
Refitting
- Place the caps ove r the wheel bolts and push them back
on .
The caps are to p rotect and keep the wheel bo lts clean. •

11ffl1.--....:..:W:...:..; h:..:.:: a:..:t :... d.::..: o:....::. I...;d:.;..:: o....:..: n..:o :...w:..:...:. ? ____________________________________________ _
• The whe el bolts s hou ld b e cl ean a nd easy to tur n. C heck for dirt
and co rros ion on t he matin g su rfac es of bot h th e whee l and th e hub.
Re mov e all d irt fro m these su rfac es before remounti ng the w heel. •
Tires with unidirectional tread design
Tir es with unidirectional tr ead d esign must b e mounted
with the ir tread patt ern pointed in th e right d ir ec tion .
Using a spare tire with a tread pattern intended for
use in a specific direction
W hen using a spare tire w ith a t read patter n inte nded for use i n a
spec ific di rec tion, please no te the fo llow in g :
• Th e directio n of ro ta ti on is mark ed by an
arrow on the side of the
tire .
• If th e spa re tir e has to be install ed in t he in cor rec t dire ction, use
the s pare t ire only tem porar ily since t he tire w ill not be a ble to
a chi eve it s opti mum perf o rma nce ch aract erist ic s wi th re gar d to
aquap lan ing, no ise and wea r.
• We re co mmen d t hat you pay part icular atten tion to t his fact
dur ing wet weather a nd that you adjust yo ur speed to match road
co ndi tions.
• Rep lace the f lat ti re with a new one and have it insta lled on your
v eh icle as so on as possible to r estor e t he hand ling advantag es o f a
unid irect ional tire .•
Notes on wheel changing
Please read the in formation => page 307, "N ew t ires and rep lacing
t ir es and w heels" if yo u are going to us e a spa re tire which is differ ent
from t he tires on yo ur vehicle .
A ft er y o u change a tir e:
• Check the tire pressure on the spare immediately after installa­
tion . •
Have the wheel bolt tightening torque checked with a torque
wrench as soon as possible by your authorized Audi dealer or a qual ­
ified workshop.
• With steel and alloy wheel rims, the wheel bolts are correctly
tightened at a torque of 90 ft lb (120 Nm ).
• If you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced befo re you check
the tightening torque.
• Replace the flat tire with a new one and have it installed on your
vehicle a s soon as possible. Remount the wheel cover.
Until then, dr ive with extra care and at reduced speeds .
& WARNING
• If you are going to equip your vehicle with tires or rims which
differ from those which were factory installed, then be sure to
read the information =>
page 307, "New tires and replacing tires
and wheels".
• Always make sure the damaged wheel or even a flat tire and
the jack and tool kit are properly secured in the luggage compart­ ment and are not loose in the passenger compartment.
• In an accident or sudden maneuver they could fly forward,
injuring anyone in the vehicle.
• Always store damaged wheel, jack and tools securely in the
luggage compartment. Otherwise, in an accident or sudden
maneuver they could fly forward, causing injury to passengers in
the vehicle. •