What do I do now? -_______________ __.PfWII
Loosening and tightening the wheel bolts
The wheel bolts must be Loosened before raising the
vehicle.
Loosening
Fig. 239 Changing a
wheel: loosening the
wheel bolts
- Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
- Take tight hold of the
end of the wrench handle and turn
the wheel bolts
counter-clockwise about one single turn
in the direction of arrow=:, fig. 239.
Tightening
-Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
- Take tight hold of the
end of the wrench handle and turn
each wheel bolt
clockwise until it is seated.
& WARNING
• Do not use force or hurry when changing a wheel· you can
cause the vehicle to slip off the jack and cause serious personal
injuries.
Vehicle OP-eration
& WARNING (continued)
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -You risk an injury.
[ i] Tips
• Never use the hexagonal socket in the handle of the screwdriver to
loosen or tighten the wheel bolts .
• If a wheel bolt is very tight, you may find it easier to loosen by
carefully pushing down on the end of the wheel bolt wrench with
one
foot only .
As you do so, hold on to the car to keep your balance and
take care not to slip. •
Raising the vehi cle
The vehicle must be Lifted with the jack first before the
wheel can be removed.
Vehicle care
Fig . 240 Changing a
wheel: mounting
points for the jack ..
Do-it-yourself service iTechnical data
III...__E_ m_ e_r-=g :.. e_ n_c -=y '-- s_i_t _u _a _ t_ i_ o _ n_ s ____________________________________________ _
-Attach the winch hook to the rear towline eye previously
installed.
[I) Tips
Check carefully to make sure the hook-up is secure before moving the
car up the flatbed truck ramp.•
Lifting vehicle
Lifting with workshop hoist and w ith floor
jack
The vehicle may only be lifted at the lifting points illus
trated.
Fig . 254 Front lifting
point
- Read and heed WARNING~ &.
Fig. 255 Rear lifting
point
-Locate lifting points~ fig. 254 and~ fig. 255.
- Adjust lifting arms of workshop hoist or floor jack to
match vehicle lifting points.
- Insert a rubber pad between the floor jack/workshop hoist
and the lifting points.
If you must lift your vehicle with a floor jack to work underneath,
be sure the vehicle is safely supported on stands intended for this
purpose.
Front Lifting point
The lifting po int is located on the floor pan re inforcement about at
the same level as the jack mounting point=> fig. 254.
Do not lift the
vehicle at the vertical sill reinforcement.
Rear lifting point
The lifting point is located on the vertical reinforcement of the lower
sill for the onboard jack=> fig . 255.
Lifting with vehicle jack
Refer to=> page 323.
_____________________________________________ E_ m_ e_r-= g ::.. e_ n_c-= y'- s_ i_t _u _a_ t_ i_ o _ n_ s __ _
& WARNING
• To reduce the risk of serious injury and vehicle damage.
-Always lift the vehicle only at the special workshop hoist and
floor jack lift points illustrated=>
page 338, fig. 254 and
=> page 338, fig. 255.
- Failure to lift the vehicle at these points could cause the
vehicle to tilt or fall from a lift if there is a change in vehicle
weight distribution and balance. This might happen, for
example, when heavy components such as the engine block or
transmission are removed .
• When removing heavy components like these, anchor vehicle
to hoist or add corresponding weights to maintain the center of
gravity. Otherwise , the vehicle might tilt or slip off the hoist ,
causing serious personal injury.
0 Note
• B e aw are of the following poi nts b efo re li fting the ve hicl e:
- The vehicle should never be lifted or jacked up from under
neath the engine oil pan, the transmission housing , the front or
rear axle or the body side members . This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame, a rubber
pad must be inserted between the floor jack and the lift points.
- Before driving over a workshop hoist, check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist.
- Before driving over a workshop hoist, ensure that there is
sufficient clearance between the hoist and low parts of the
vehicle. •
Safety first Vehicle care Do-it-yourself service Technical data
