2010 ASTON MARTIN V8 VANTAGE warning

Instrument Cluster (13.01)
Information, Gauge and Warning (13.00)
May 2007 Workshop Manual 13-1-3
Information and Warning Lamps
Name / FunctionDescriptionSymbolInput SignalPower
On Check
General Warning
– Amber/Red Controlled internally by the DIM. It is used in conjunction with
several text messages to indicate information to the driver. Internal
SRS (Airbag) Controlled externally by the SRS module and indicates a fault in the SRS module. CAN Yes (5 Seconds)
High Engine
Coolant Temp. This tell tale is controlled internally by the DIM. Activated
when the engine coolant temperature signal from the CAN bus
reaches a pre defined value. (The
actual symbol is not lit, only
the red LED.) CAN
DSC Controlled externally by the ABS/DSC module. Indicates when the system is in operation or when it is turned off. The tell tale
is triggered by a CAN signal. CAN Yes (5 Seconds)
ABS Controlled externally by th e ABS/DSC module. Indicates a
fault in the ABS system. The tell tale is triggered by a CAN
signal. CAN Yes (5 Seconds)
Rear Fog Lights Controlled externally by the SRS module. Indicates that the
rear fog lights are turned on. The tell tale is triggered by a CAN
signal. CAN Yes (5 Seconds)
Seat Belts Controlled externally by the CEM. Indicates that the seat belts are not fastened properly. The tell tale is triggered by a CAN
signal. CAN Yes (5 Seconds)
Brake (General) Controlled externally by either the CEM or the ABS / DSC module. It indicates low brake fluid level, brake fault and park
brake. The tell tale is triggered by two low side inputs or a CAN
signal. Low side x 2
and
CAN Ye s ( 5 S e c o n d s )
Side Lights Controlled externally by th e CEM. Indicates that the side lights
are on. High side
Oil Pressure Controlled exte rnally by the PCM. Indicates low oil pressure.
The tell tale is triggered by a CAN signal. CAN Yes (5 Seconds)
Battery Charge Controlled externally by th e CEM. Indicates that the alternator
is no longer charging the battery properly. The tell tale is
triggered by a CAN signal. CAN Yes (5 Seconds)
Fuel Level Low Controlled internally by the DIM. Activated when the fuel level drops below a pre defined value. The fuel information is
provided from the CAN bus. The symbol is not lit, only the
amber LED. CAN
Turn Left/Right Controlled externally by th e CEM. The tell tale is triggered by a
CAN signal. CAN
High Beam Controlled externally by the CEM. Indicates that the high beam is switched on. The tell tale is triggered by a CAN signal. CAN
Check Engine Controlled externally by the PCM. Indicates a fault in the engine management system. The te ll tale is not connected to
the microprocessor. Low side
Tyre Pressure Controlled by the DIM. In dicates a low or rapid change in the
tyre pressure or a tyre pressure monitoring system fault. Low side Yes (5 Seconds)
Not Used
PATS Controlled externally by the PCM. Indicates key acceptance status. Low side

Instrument Cluster (13.01)
Information, Gauge and Warning (13.00)13-1-4 Workshop Manual May 2007
DIM Display layout
The DIM contains two message centres, which are used to
inform the driver about the vehicles status.

Message Centres
The left Message Centre is used to display the odometer (C),
the Cruise control status (C) and the T1 or T2 trip distance
(A).
Shift Position Sensor
The Shift Position Sensor display indicates when the shift
lights are activated. The display is duel colour.
Green - normal operation
Red - defined situations.
Message Centre Right
The Message Centre Right is used to display the trip function
information and warning/information messages.

0HVVDJH &HQWUH /HIW 6KLIW
3RVLWLRQ 6HQVRU 0HVVDJH
&HQWUH5LJKW

$
& %


Battery System (14.01)
Power Supply (14.00)14-1-4 Workshop Manual May 2007
Specifications
Maintenance
Battery Disconnect Switch-Renew
Removal
1. Power RH seat fully forward.
2. Remove rear compartment cover.
3. Disconnect vehicle battery.
4. Remove panel assembly - quar ter trim middle - RH (see
Workshop Manual procedure 01.05.CL Panel Assembly
- Quarter Trim Middle Section - RH - Renew).
5. Release rear carpet studs (x2), move carpet aside.
6. Remove screws (x2), battery compartment cover to support rail.
7. Remove nuts (x2), RH rear heel board to body. Remove heel board.
8. Remove nuts/washers (x2), securing battery cables to battery disconnect switch (see Fig. 1).
9. Release battery cables (x4) from battery disconnect switch. Note fitted position of spacer washer between
RH battery cables.
10. Remove Torx screws (x3), securing battery disconnect switch to mounting bracket. 11. Release multiplug from brac
ket, disconnect multiplug,
remove battery disconnect switch.
12. Remove battery cable bolts from battery disconnect switch.
Installation
1. Install battery cable bolts in disconnect switch.
2. Position battery disconnect switch, connect multiplug, install multiplug on bracket.
3. Install and torque tighten Torx screws (x3).
4. Install battery cables (x4), install washers (x2), install and torque tighten nuts (x2).
5. Install RH rear heel board, install and tighten screws (x2) and nuts (x2).
6. Position rear carpet, install on studs (x2).
7. Connect vehicle battery.
8. Install panel assembly - quarter trim middle - RH (see Workshop Manual procedure 01.05.CL Panel Assembly
- Quarter Trim Middle Section - RH - Renew).
9. Install rear compartment cover.
10. Power RH seat to original position.
Battery Conditioner-Renew
Removal
1. Disconnect vehicle battery.
2. Remove carpet - RH side luggage compartment (see Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew).
3. Remove tyre sealant bottle.
4. Remove mobility kit from storage rack.
5. Remove bolt, loosen nuts (x2), power socket bracket.
6. Slide luggage compartment fusebox rearwards, release
from mounting bracket.
7. Release terminal cover, remove nut securing main battery lead to fusebox.
8. Release harness clips (x2) from power socket bracket.
Torque Figures
DescriptionNm.lb. / ft.
Battery clamp
Battery Terminals 9
97
7
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be
disconnected first and reconnected last.
Fig. 1
$
Warning
Always connect the earth (- ve) terminal last.
Repair Operation Time (ROT)
ItemCode
Battery Conditioner-Renew 14.01.DL
Warning
To prevent damage to elec trical components, always
disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be
disconnected first and reconnected last.

Battery System (14.01)
Power Supply (14.00)
May 2007 Workshop Manual 14-1-5
9. Disconnect harness multiplu g, battery conditioner (see
Fig. 1).
10. Remove screws (x2), battery conditioner to power socket bracket. Remove battery conditioner (see Fig. 2).
Installation
1. Install battery conditioner, install and tighten screws (x2).
2. Connect multiplug, battery conditioner.
3. Install harness clips (x2) on power socket bracket.
4. Position main battery cable, install and torque tighten nut, install terminal cover.
5. Install fusebox in mounting bracket.
6. Install harness clips (x2) on power socket bracket.
7. Position power socket bracket, install bolt. torque tighten bolt and nuts (x2).
8. Install mobility kit.
9. Install tyre sealant bottle.
10. Install carpet - RH side luggage compartment. (see Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew). 11. Connect vehicle battery.
Battery Disconnect Switch to Bulkhead
Stud Cable Assembly-Renew
Removal
1. Remove RH seat (see Workshop Manual procedure
01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
2. Disconnect vehicle battery.
3. Remove screws (x4) front fl oor carpet retaining brackets
(x2) to floor.
4. Release RH front floor car pet from fasteners (x4),
remove carpet.
5. Release RH rear floor carpet from fasteners (x4), remove
carpet.
6. Release and remove RH tunnel carpet.
7. Remove moulding assembly - quarter trim upper RH (see Workshop Manual procedure 01.05.CX Moulding
Assembly - Quarter Trim Upper - RH - Renew).
8. Remove nuts (x2) and scre ws (x2) securing RH heel
board to body and support rail. Remove heel board.
9. Remove nuts (x3) and scre ws (x6) securing CEM cover
plate to body, remove cover plate.
10. Remove screws (x2) securing CEM to mounting bracket. Position CEM aside.
11. Release cover, remove nut securing battery cables (x3)
to bulkhead stud (see Fig. 1).
Fig. 1
Fig. 2
Warning
Always connect the earth (- ve) terminal last.
$
$
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be disconnected first an d reconnected last.
$

Battery System (14.01)
Power Supply (14.00)14-1-6 Workshop Manual May 2007
12. Note fitted position and remove battery cables (x3) from bulkhead stud.
13. Release clips (x2) securi ng main harness to body.
14. Release battery cable clips (x22) from body.
15. Remove nut securing battery cable to BDS, release cable
from BDS (see Fig. 2).
16. Remove power amplifier assembly (see Workshop Manual procedure 15.01.AB Power Amplifier - Renew).
17. Remove tyre sealant bottle.
18. Remove mobility kit from storage rack.
19. Release terminal cover, remove nut securing battery
cable to luggage compartmen t fuse box (see Fig. 3).
20. Release battery cable from fuse box and clips (x7).
21. Manoeuvre and remove battery cable from vehicle.
Installation
1. Manoeuvre and install battery cable in vehicle.
2. Connect battery cable to luggage compartment fuse box, install and torque tighten nut. Install terminal
cover.
3. Install clips (x7), secure battery cable to body. 4. Install mobility kit in storage rack.
5. Install tyre sealant bottle.
6. Install power amplifier assembly (see Workshop Manual
procedure 15.01.AB Power Amplifier - Renew).
7. Connect battery cable to BDS, install and torque tighten nut.
8. Install clips (x22), secure battery cable to body.
9. Secure main harness to body with clips (x2).
10. Connect battery cables (x3) to bulkhead stud, install and torque tighten nut. Install terminal cover.
11. Position CEM to mounting bracket, install and torque tighten screws (x2).
12. Install CEM cover plate, Install and torque tighten nuts (x3) and screws (x6).
13. Install RH heel board, install and torque tighten nuts (x2) and screws (x2).
14. Install moulding assembly - quarter trim upper RH (see
Workshop Manual procedure 01.05.CX Moulding
Assembly - Quarter Trim Upper - RH - Renew).
15. Install and secure tunnel carpet RH.
16. Install RH rear floor carpe t and secure with fasteners
(x4).
17. Install RH front floor carpet and secure with fasteners (x4).
18. Install front floor carpet retaining brackets (x2)
19. Install RH seat (see Workshop Manual procedure 01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
20. Connect vehicle battery.
Battery to Battery Disconnect Switch
Cable Assembly-Renew
Removal
1. Power RH seat fully forward.
2. Remove rear compartment cover.
3. Disconnect vehicle battery.
4. Remove panel assembly - quar ter trim middle - RH (see
Workshop Manual procedure 01.05.CL Panel Assembly
- Quarter Trim Middle Section - RH - Renew).
5. Release rear carpet studs (x2), move carpet aside.
6. Remove screws (x2), battery compartment cover to support rail.
Fig. 1
Fig. 2
Fig. 3
$
$

Warning
Always connect the earth (- ve) terminal last.
Repair Operation Time (ROT)
ItemCode
Battery to Battery Disconnect Switch
Cable Assembly-Renew 14.01.EF
Warning
To prevent damage to elec trical components, always
disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be disconnected first and reconnected last.

Battery System (14.01)
Power Supply (14.00)
May 2007 Workshop Manual 14-1-7
7. Remove nuts (x2), battery compartment cover to body.
Remove cover.
8. Loosen terminal nut, disconnect main battery cable (see Fig. 1).
9. Remove nut and washer securing battery cable to battery disconnect switch.
10. Release cable and main battery cable from battery disconnect switch.
11. Loosen terminal nut, disconnect main battery cable (positive), remove cable.
Installation
1. Install battery cables (x2), install washer, install and torque tighten nut.
2. Install battery compartment cover, install and tighten screws (x2) and nuts (x2).
3. Position rear carpet, install on studs (x2).
4. Connect vehicle battery.
5. Install panel assembly - quar ter trim middle section - RH
(see Workshop Manual pr ocedure 01.05.CL Panel
Assembly - Quarter Trim Mi ddle Section - RH - Renew).
6. Install rear compartment cover.
7. Power RH seat to original position.
Bulkhead to Starter Jump Terminal
Harness-Renew
Removal
1. Disconnect vehicle battery.
2. Remove terminal jump start (see Workshop Manual procedure 14.01.EA Terminal - Jump Start - Renew).
3. Raise vehicle on ramp.
4. Remove RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
5. Release battery cable clips (x6), from body (see Fig. 1).
6. Release battery cable clips (x2) from screen washer reservoir (see Fig. 2).
7. Release cover, remove nut securing harness to bulkhead stud.
8. Release harness from bulkhead stud, manoeuvre and remove harness.
Fig. 1
Warning
Always connect the earth (- ve) terminal last.
Repair Operation Time (ROT)
$
Warning
To prevent damage to electrical components, always
disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be disconnected first an d reconnected last.
Fig. 1
Fig. 2
$
$

Battery System (14.01)
Power Supply (14.00)14-1-8 Workshop Manual May 2007
Installation
1. Position harness to bulkhead stud, install and torque tighten nut, install cover.
2. Secure harness to body an d screen washer reservoir
with clips (x8).
3. Install RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Lower vehicle on ramp.
5. Install terminal jump start (see Workshop Manual procedure 14.01.EA Terminal - Jump Start - Renew).
6. Connect vehicle battery.
BDS to Bulkhead Dirty Feed Harness-
Renew
Removal
1. Remove RH seat (see Workshop Manual procedure 01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
2. Disconnect vehicle battery.
3. Remove screws (x4), retaining brackets securing front floor carpet, remove brackets (x2).
4. Release RH rear floor carpet from fasteners (x4), remove carpet.
5. Remove nuts (x2) and screws (x2) securing RH rear heel board to body and support rail then remove heel board.
6. Remove nuts (x3) and scre ws (x6) securing CEM cover
plate to body, remove cover plate. 7. Release cover, remove nut securing battery dirty feed
cable to bulkhead stud (see Fig. 1).
8. Release battery dirty feed cable clips (x9) from body.
9. Remove nut securing battery dirty feed cable to battery disconnection switch, release cable from battery
disconnection switch (see Fig. 2).
10. Remove battery dirty feed cable from vehicle.
Installation
1. Install battery dirty feed cable in vehicle.
2. Connect battery dirty feed cable to battery disconnection switch, insta ll and torque tighten nut.
3. Secure battery dirty feed cab le to body with clips (x9).
4. Connect battery dirty feed cable to bulkhead stud, install and torque tighten nut.
5. Install terminal cover.
6. Install CEM cover plate, Install and torque tighten nuts (x3) and screws (x6).
7. Install RH rear heel board, install and torque tighten nuts (x2) and screws (x2).
8. Install RH rear floor carpet and secure with fasteners (x4).
Warning
Always connect the earth (- ve) terminal last.
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be disconnected first and reconnected last.
Fig. 1
Fig. 2
$
$

Battery System (14.01)
Power Supply (14.00)
May 2007 Workshop Manual 14-1-9
9. Install front floor carpet retaining brackets (x2), install and tighten screws (x4)
10. Install RH seat (see Wo rkshop Manual procedure
01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
11. Connect vehicle battery.
Warning
Always connect the earth (- ve) terminal last.