2010 ASTON MARTIN V8 VANTAGE sensor

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-3
2. Remove bolts (x3) that attach the oil scavenge pump to sump (refer to Figure 1).
3. Remove oil scavenge pump, remove and discard gasket (refer to Figure 2).
4. Release chain from oil pu mp drive sprocket, remove
chain (refer to Figure 3).Installation
1. Clean oil scavenge pump and mating face on sump.
2. Install new oil scavenge pump gasket, align on dowels (x2).
3. Install chain onto oil scavenge pump sprocket.
4. Install oil scavenge pump, align to dowels (x2), Install and torque tighten bolts (x3).
5. Install chain onto oil pump drive sprocket.
6. Install oil pressure pump gasket (refer to Workshop
Manual procedure 03.02.AG Gasket - Oil Pressure
Pump to Sump - Renew).
Oil Sump Pan - Renew
Removal
1. Remove oil sump (refer to Workshop Manual procedure
03.02.BN Pan - Oil Sump - Remove and Reseal).
2. Remove bolt that attach the crankshaft timing sensor, remove sensor (refer to Figure 1).
Figure 1
Figure 2
Figure 3
A0302274
A0302276
Repair Operation Time (ROT)
A0302305

Lubrication System (03.02)
Engine (03.00)3-2-4 Workshop Manual Issue 5, Janauary 2010
3. Remove oil pressure sensor (refer to Figure 2).
4. Remove engine electric coolant temperature sensor (refer to Figure 3).
5. Remove Torx screws (x4) that attach the oil filter plates
(x2) to sump. Remove plates (refer to Figure 4). 6. Install suitable bolt and remove filters (x2) from sump
(refer to Figure 5).
7. Remove oil filter adaptor (refer to Figure 6).
Figure 2
Figure 3
Figure 4
A0302306
A0302306A
A0302305A
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Figure 5
Figure 6
A0302308
A0302306B

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-5
8. Press out alternator mounting bushes (x2) from sump (refer to Figure 7).
9. Remove dowels (x4) from sump for oil pressure and scavenge pumps location (refer to Figure 8). 10. Remove Torx screws (x2) that attach the oil pump(s)
chain guide, remove chain gu ide (refer to Figure 9).
11. Remove oil plug from sump.
Installation
1. Clean chain guide, oil filter adaptor, filters (x2), sump plug , pump(s) dowels and crankshaft timing sensor.
2. Install alternator bushes.
3. Install oil filter adaptor.
4. Install filters (x2), install oil filter plates (x2), install and
torque tighten Torx screws (x4).
5. Install oil plug.
6. Install oil pump(s) dowels (x4).
7. Clean old sealant from sensor threads (x2).
8. Apply sealant to engine electric coolant temperature sensor threads, install and torque tighten sensor.
9. Apply sealant to oil pressure sensor threads, install and torque tighten sensor.
10. Install oil pump(s) chain guid e, Install and torque tighten
Torx screws (x2).
11. Install crankshaft timing sensor, install and torque tighten bolt.
12. Install oil sump (refer to Workshop Manual procedure 03.02.BN Pan - Oil Sump - Remove and Reseal).
Oil Sump Pan - Remove and Reseal
Removal
1. Remove oil pump(s) drive chain (refer to Workshop Manual procedure 03.02.AJ Chain - Oil Pump - Renew).
Figure 7
Figure 8
A030206C
A0302307
Figure 9
Repair Operation Time (ROT)
A0302307A

Lubrication System (03.02)
Engine (03.00)3-2-6 Workshop Manual Issue 5, Janauary 2010
2. Disconnect multiplug from oi l pressure sensor (refer to
Figure 1).
3. Disconnect multiplug from engine electric coolant
temperature sensor (refer to Figure 2). 4. Disconnect multiplug from
crankshaft timing sensor
(refer to Figure 3).
5. Release harness clips (x6) from sump (refer to Figure 4).
Figure
Figure 2
A030216
A030216A
Figure 3
Figure 4
A030206
A030206B

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-7
6. Remove bolts (x4) that attach the LH and RH HEGO sensor multiplug brackets to sump (refer to Figure 5).
7. Disconnect multiplug from A/C compressor.
8. Remove bolts (x4) that attach the A/C compressor to mounting bracket. Tie compressor aside.
9. Remove bolts (x2) that attach the inlet and outlet oil pipes to sump (refer to Figure 6).
10. Release both oil pipes toge ther from sump, remove and
discard O-ring seals from pipes. 11. Remove Torx bolts (x4) that attach the A/C compressor
mounting bracket to engine bedplate and sump.
Remove bracket (refer to Figure 7).
12. Note fitted position of clutch bleed tube bracket, remove bolts (x4) that attach the torque tube to sump
(refer to Figure 8).
Figure 5
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Figure 6
A030206C
A030247
Figure 7
Figure 8
A0302303
A0302304

Lubrication System (03.02)
Engine (03.00)3-2-8 Workshop Manual Issue 5, Janauary 2010
13. Remove bolts (x16) that attach the sump to engine bedplate (refer to Figure 9).
14. Release and remove sump.
Installation
1. Clean old sealant from sump flange and engine bedplate.
2. Ensure that sump flange and mating face on engine bedplate are clean and dry.
3. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
4. Ensure that there are no gaps in sealant track.
5. Install sump, install bolts (x16). Do not torque tighten at this stage.
6. Install bolts (x4), sump to torque tube, lightly tighten bolts and then loosen bolts.
7. Torque tighten sump bolts (x16) in the recommended sequence.
8. Torque tighten sump to torque tube bolts (x4).
9. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
10. Lubricate and install new O-ring seals to oil pipes.
11. Install oil pipes in sump, install and torque tighten bolts (x2)
12. Install compressor, install and torque tighten bolts (x4). 13. Connect multiplug to A/C compressor.
14. Install LH and RH HEGO
sensor multiplug brackets to
sump. Install and torque tighten bolts (x4).
15. Secure harness clips (x6) in sump.
16. Connect multiplug to crankshaft timing sensor.
17. Connect multiplug to engine electric coolant temperature sensor.
18. Connect multiplug to oil pressure sensor.
19. Install oil pump(s) drive chain (refer to Workshop
Manual procedure 03.02.AJ Chain - Oil Pump - Renew).
Oil Cooler - Renew
Removal
1. Raise vehicle on ramp.
2. Remove undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
3. Remove pipes from oil cooler (position container to catch oil) (refer to Figure).
Figure 1
4. Remove oil cooler from body (bolts x4).
5. Remove duct from oil cooler (bolts x4).
Installation
1. Install duct from to cooler (bolts x4) (torque).
2. Install oil cooler to body (bolts x4) (torque).
3. Install pipes to oil cooler (torque).
4. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
5. Lower vehicle on ramp.
Figure 9
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
A030206D
Repair Operation Time (ROT)
ItemCode
Oil Cooler - Renew 03.02.BX
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Make sure that all open ends of oil cooler pipes and oil cooler connections are plugged to prevent dirt or
foreign material entering the lubrication system.

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-15
2. Remove bolt that attach the crankshaft timing sensor, remove sensor (refer to Figure 1).
3. Remove oil pressure sens or (refer to Figure 2).
4. Remove engine electric coolant temperature sensor (refer to Figure 3). 5. Remove Torx screws (x4) that
attach the oil filter plates
(x2) to sump. Remove plates (refer to Figure 4).
6. Install suitable bolt and re move filters (x2) from sump
(refer to Figure 5).
Figure 1
Figure 2
Figure 3
A0302305
A0302306
A0302306A
Figure 4
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Figure 5
A0302305A
A0302308

Lubrication System (03.02)
Engine (03.00)3-2-16 Workshop Manual Issue 5, Janauary 2010
7. Remove oil filter adaptor (refer to Figure 6).
8. Press out alternator mounting bushes (x2) from sump (refer to Figure 7). 9. Remove dowels (x4) from
sump for oil pressure and
scavenge pumps location (refer to Figure 8).
10. Remove Torx screws (x2) that attach the oil pump(s)
chain guide, remove chain gu ide (refer to Figure 9).
11. Remove oil plug from sump.
Installation
1. Clean chain guide, oil filter adaptor, filters (x2), sump plug , pump(s) dowels and crankshaft timing sensor.
2. Install alternator bushes.
3. Install oil filter adaptor.
4. Install filters (x2), install oil filter plates (x2), install and
torque tighten Torx screws (x4).
5. Install oil plug.
6. Install oil pump(s) dowels (x4).
7. Clean old sealant from sensor threads (x2).
8. Apply sealant to engine electric coolant temperature sensor threads, install and torque tighten sensor.
9. Apply sealant to oil pressure sensor threads, install and torque tighten sensor.
Figure 6
A030206B
A030206C
Figure 7
Figure 8
Figure 9
A0302307
A0302307