2010 ASTON MARTIN V8 VANTAGE fuse box

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
12-3-6 Workshop Manual May 2007
Diagnostics
Electrical Connectors
A/C Module (C0792)



A/C Module (C0791)
PinSpecification
1 Air flow mode actuator (output)
2 Temperature actuator (output)
3Blank
4Blank
5Blank
6 A/C On (A/C pressure sensor)
7Blank
8 Recirculation actuator (output)
9Blank
10 Blank
11 Temperature level (RHD)
12 Blower speed regulator (Output)
13 Air flow mode actuator (output)
14 Temperature actuator (output)
15 Blank
16 Output
17 HAVAC ECU (input)
18 Blank
19 Blower relay (engine bay fusebox)
20 Recirculation actuator (output)
21 Blank
22 blank
23 Temperature level (LHD)
24 Blower speed regulator input)




Battery System (14.01)
Power Supply (14.00)
May 2007 Workshop Manual 14-1-3
Charging Circuit
Electrical power generated at the alternator flows via two ‘T Pi ece’ connectors to the engine bay ‘Dirty Feed’ stud. It then
flows via the Battery Disconnect Switch (BDS) to the battery positive terminal. Both the alternator and the battery are
earthed via the vehicle body to complete the charging circuit.
The starter motor and the ‘jump start terminal’ ar e also fed directly from the charging circuit.
Go to page 18-X-XX for complete power dist ribution circuit diagram (Circuit Sheet 25).
+12 Volt Distribution
The +12 volt supply comes from the battery to the battery disc onnect switch (BDS). Assuming that this switch is not
activated, 12 volt power is then available from C0046-8 on the BDS to all of the clean feed battery studs.
The following clean feeds are then live:
• Boot fuse box clean feed
• Under bonnet fuse box clean feed
• CEM busbars 1, 2, 3 and 4 clean feeds
12V power to all systems and components is then controlled by the CEM and the under bonnet / boot fuse boxes.

Battery System (14.01)
Power Supply (14.00)14-1-4 Workshop Manual May 2007
Specifications
Maintenance
Battery Disconnect Switch-Renew
Removal
1. Power RH seat fully forward.
2. Remove rear compartment cover.
3. Disconnect vehicle battery.
4. Remove panel assembly - quar ter trim middle - RH (see
Workshop Manual procedure 01.05.CL Panel Assembly
- Quarter Trim Middle Section - RH - Renew).
5. Release rear carpet studs (x2), move carpet aside.
6. Remove screws (x2), battery compartment cover to support rail.
7. Remove nuts (x2), RH rear heel board to body. Remove heel board.
8. Remove nuts/washers (x2), securing battery cables to battery disconnect switch (see Fig. 1).
9. Release battery cables (x4) from battery disconnect switch. Note fitted position of spacer washer between
RH battery cables.
10. Remove Torx screws (x3), securing battery disconnect switch to mounting bracket. 11. Release multiplug from brac
ket, disconnect multiplug,
remove battery disconnect switch.
12. Remove battery cable bolts from battery disconnect switch.
Installation
1. Install battery cable bolts in disconnect switch.
2. Position battery disconnect switch, connect multiplug, install multiplug on bracket.
3. Install and torque tighten Torx screws (x3).
4. Install battery cables (x4), install washers (x2), install and torque tighten nuts (x2).
5. Install RH rear heel board, install and tighten screws (x2) and nuts (x2).
6. Position rear carpet, install on studs (x2).
7. Connect vehicle battery.
8. Install panel assembly - quarter trim middle - RH (see Workshop Manual procedure 01.05.CL Panel Assembly
- Quarter Trim Middle Section - RH - Renew).
9. Install rear compartment cover.
10. Power RH seat to original position.
Battery Conditioner-Renew
Removal
1. Disconnect vehicle battery.
2. Remove carpet - RH side luggage compartment (see Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew).
3. Remove tyre sealant bottle.
4. Remove mobility kit from storage rack.
5. Remove bolt, loosen nuts (x2), power socket bracket.
6. Slide luggage compartment fusebox rearwards, release
from mounting bracket.
7. Release terminal cover, remove nut securing main battery lead to fusebox.
8. Release harness clips (x2) from power socket bracket.
Torque Figures
DescriptionNm.lb. / ft.
Battery clamp
Battery Terminals 9
97
7
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be
disconnected first and reconnected last.
Fig. 1
$
Warning
Always connect the earth (- ve) terminal last.
Repair Operation Time (ROT)
ItemCode
Battery Conditioner-Renew 14.01.DL
Warning
To prevent damage to elec trical components, always
disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be
disconnected first and reconnected last.

Battery System (14.01)
Power Supply (14.00)
May 2007 Workshop Manual 14-1-5
9. Disconnect harness multiplu g, battery conditioner (see
Fig. 1).
10. Remove screws (x2), battery conditioner to power socket bracket. Remove battery conditioner (see Fig. 2).
Installation
1. Install battery conditioner, install and tighten screws (x2).
2. Connect multiplug, battery conditioner.
3. Install harness clips (x2) on power socket bracket.
4. Position main battery cable, install and torque tighten nut, install terminal cover.
5. Install fusebox in mounting bracket.
6. Install harness clips (x2) on power socket bracket.
7. Position power socket bracket, install bolt. torque tighten bolt and nuts (x2).
8. Install mobility kit.
9. Install tyre sealant bottle.
10. Install carpet - RH side luggage compartment. (see Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew). 11. Connect vehicle battery.
Battery Disconnect Switch to Bulkhead
Stud Cable Assembly-Renew
Removal
1. Remove RH seat (see Workshop Manual procedure
01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
2. Disconnect vehicle battery.
3. Remove screws (x4) front fl oor carpet retaining brackets
(x2) to floor.
4. Release RH front floor car pet from fasteners (x4),
remove carpet.
5. Release RH rear floor carpet from fasteners (x4), remove
carpet.
6. Release and remove RH tunnel carpet.
7. Remove moulding assembly - quarter trim upper RH (see Workshop Manual procedure 01.05.CX Moulding
Assembly - Quarter Trim Upper - RH - Renew).
8. Remove nuts (x2) and scre ws (x2) securing RH heel
board to body and support rail. Remove heel board.
9. Remove nuts (x3) and scre ws (x6) securing CEM cover
plate to body, remove cover plate.
10. Remove screws (x2) securing CEM to mounting bracket. Position CEM aside.
11. Release cover, remove nut securing battery cables (x3)
to bulkhead stud (see Fig. 1).
Fig. 1
Fig. 2
Warning
Always connect the earth (- ve) terminal last.
$
$
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be disconnected first an d reconnected last.
$

Battery System (14.01)
Power Supply (14.00)14-1-6 Workshop Manual May 2007
12. Note fitted position and remove battery cables (x3) from bulkhead stud.
13. Release clips (x2) securi ng main harness to body.
14. Release battery cable clips (x22) from body.
15. Remove nut securing battery cable to BDS, release cable
from BDS (see Fig. 2).
16. Remove power amplifier assembly (see Workshop Manual procedure 15.01.AB Power Amplifier - Renew).
17. Remove tyre sealant bottle.
18. Remove mobility kit from storage rack.
19. Release terminal cover, remove nut securing battery
cable to luggage compartmen t fuse box (see Fig. 3).
20. Release battery cable from fuse box and clips (x7).
21. Manoeuvre and remove battery cable from vehicle.
Installation
1. Manoeuvre and install battery cable in vehicle.
2. Connect battery cable to luggage compartment fuse box, install and torque tighten nut. Install terminal
cover.
3. Install clips (x7), secure battery cable to body. 4. Install mobility kit in storage rack.
5. Install tyre sealant bottle.
6. Install power amplifier assembly (see Workshop Manual
procedure 15.01.AB Power Amplifier - Renew).
7. Connect battery cable to BDS, install and torque tighten nut.
8. Install clips (x22), secure battery cable to body.
9. Secure main harness to body with clips (x2).
10. Connect battery cables (x3) to bulkhead stud, install and torque tighten nut. Install terminal cover.
11. Position CEM to mounting bracket, install and torque tighten screws (x2).
12. Install CEM cover plate, Install and torque tighten nuts (x3) and screws (x6).
13. Install RH heel board, install and torque tighten nuts (x2) and screws (x2).
14. Install moulding assembly - quarter trim upper RH (see
Workshop Manual procedure 01.05.CX Moulding
Assembly - Quarter Trim Upper - RH - Renew).
15. Install and secure tunnel carpet RH.
16. Install RH rear floor carpe t and secure with fasteners
(x4).
17. Install RH front floor carpet and secure with fasteners (x4).
18. Install front floor carpet retaining brackets (x2)
19. Install RH seat (see Workshop Manual procedure 01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
20. Connect vehicle battery.
Battery to Battery Disconnect Switch
Cable Assembly-Renew
Removal
1. Power RH seat fully forward.
2. Remove rear compartment cover.
3. Disconnect vehicle battery.
4. Remove panel assembly - quar ter trim middle - RH (see
Workshop Manual procedure 01.05.CL Panel Assembly
- Quarter Trim Middle Section - RH - Renew).
5. Release rear carpet studs (x2), move carpet aside.
6. Remove screws (x2), battery compartment cover to support rail.
Fig. 1
Fig. 2
Fig. 3
$
$

Warning
Always connect the earth (- ve) terminal last.
Repair Operation Time (ROT)
ItemCode
Battery to Battery Disconnect Switch
Cable Assembly-Renew 14.01.EF
Warning
To prevent damage to elec trical components, always
disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead ( - ve) must be disconnected first and reconnected last.

May 2007 Workshop Manual 18-1-1
Electric Distribution/Electronic Control (18.00)
Contents
Wiring and Circuit Protection (18.01) ................. 18-1-2Fuse Boxes .............................................................. 1-2 Engine Bay Fuse/Relay Box..................................... 1-2
Central Electronics Module Fusebox....................... 1-3
How to Read the Circuits........................................ 1-4 Wires ..................................................................... 1-4
Controller Area Network (CAN).............................. 1-5
Media Oriented System Transport (MOST) ............. 1-6
Connectors ............................................................. 1-6 Splices ................................................................... 1-7
Relays .................................................................... 1-8
Busbars .................................................................. 1-8
Fuses ..................................................................... 1-8
Resistors................................................................. 1-9
Lamps .................................................................... 1-9
Switches ................................................................ 1-9
Motors and Pumps ................................................. 1-9
Diodes ................................................................. 1-10
Transistor ............................................................. 1-10
Earth / Ground ..................................................... 1-10
Maintenance ......................................................... 1-11 Forward Harness-Renew ...................................... 1-11
Header Latch Harness-Renew
(Roadster Only) .................................................... 1-12
Roof Cylinder Wiring Harness-Renew
(Roadster Only) .................................................... 1-14
Transaxle Harness-Renew .................................... 1-21
Engine Wiring Harness-Renew ............................. 1-22
Facia Harness-Renew ........................................... 1-25
Cabin Harness Assembly-Renew .......................... 1-26
Passenger Door Harness-Renew ........................... 1-36
Driver’s Door Harness-Renew .............................. 1-36
Rear Bumper Harness-Renew .............................. 1-37
Transaxle Harness-Renew .................................... 1-37
Axle Transmission Harness-Renew
-Sportshift Only.................................................... 1-38
Tailgate Harness-Renew ....................................... 1-38
Vehicle Control System (18.08) ........................... 18-2-1 Module Configuration ............................................ 2-1 Principles of Operation .......................................... 2-1
Market Configuration ............................................. 2-1
Customer Configuration ......................................... 2-1
Data Buses .............................................................. 2-1
Network Bus ........................................................... 2-1 MOST.................................................................... 2-1
Module Locations ................................................... 2-2

Wiring and Circuit Protection (18.01)
Electric Distribution/E lectronic Control (18.00)
18-1-2 Workshop Manual May 2007
Electric Distribution/Electronic Control (18.00)
Wiring and Circuit Protection (18.01)
Fuse Boxes
From the clean 12V output terminal of the battery
disconnect switch, electrical power is distributed to three
fuse boxes:
• Engine bay fuse box (LH side of engine bay on LH drive vehicles)
• Boot fuse box

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-3
F26 20A Headlamp wash pump (HID Only)
F27 25A Spare
F28 10A Module - ABS/Key Reader and Steering angle sensors
F29 25A Spare
F30 5A Alternator battery sensing
F31 30A Heated front screen
F32 30A Wiper (slow)
F33 30A Wiper (fast)
F34 20A Heater Blower motor
F35 60A Cooling fan module
Central
Electronics
Module
Fusebox
Fuse/
RelayRatingFunction
F43 10A Multi media module display/Phone/GPS tuner/Media player
F44 10A Airbag module
F45 15A Accessory socket and illumination
F46 5A Driver Information/Master light switch/Glove box relay/Master lock switch Battery Off
switch/Boot release switch/Speaker-switch/
JBFB-R7/Centre console module/Bluetooth
module
F47 5A Interior lamps (front)/Seat switches/Fuel flap switch/glovebox switch/Rear power
illumination
F48 15A Windscreen wash pump
F49 10A Occupant detect (Driver and passenger seat)/Airbag module
F50
F51 10A Diagnostic connectors/Centre stack switches
F52 5A Start button
F53 10A Module - HID lighting
F54 10A Engine fuse box/Boot fuse box/Tyre pressure monitor module/Satellite navigation relay
F55
F56 10A Centre console module/Sounder module/
Hazard switch
F57 15A Diagnostic connectors/Brake pedal switch
F58 10A High beam (RH)
F59 10A High beam (LH)
F60 15A Drivers seat power (Heating)
F61 15A Passenger seat power (Heating)
F62 20A A/C module
F63 20A
F64 5A AM/FM receiver module/Traffic Monitoring Control module (TMC)
F65 5A Media player/Multi media module and display/Audio amplifier
F66 10A Centre console module/Infotainment control module
F67
F68
F69 5A BFB-R5
F70
F71
F72
F73
F74 15A Fuel pump
F75
F76
F77 15A Boot power socket
F78
F79 5A Reversing lamps/Module - Parking aid
F80 5A Battery ‘Off’ switch
F81 20A Ignition switch
F82 25A Passenger door module
F83 25A Driver door module
F84 25A Passenger seat power/Passenger seat switchpack
F85 25A Driver seat power/Driver seat switchpack
F86 5A Start button, Driver and passenger seats