2010 ASTON MARTIN V8 VANTAGE O2 sensor

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-13
38. Remove the four Torx bolts that attach the PAS pump mounting bracket to the cylinder block. Remove the
bracket (refer to Figure 9).
Figure 9
39. Remove the 27 bolts that attach the timing cover to the engine. Collect the bracet for the oil separator drain
tube. Remove the timing cover.
40. Remove the outer and inner rubber seals from the timing cover (refer to Figure0).
Figure0
41. Remove the front crankshaft oil seal from timing cover.
Installation
1. Clean the timing cover and mating face on engine.
2. Install the inner and outer seals into timing cover.
3. Apply 3mm x 12mm beads of sealant to the eight joints
on the engine.
4. Install the timing cover. Put the oil separator drain tube bracket in position. Install the 27 bolts and torque the
bolts in the specified sequence. 5. Using tool (303-750), instal
l front crankshaft oil seal.
Remove special tool and seal protector.
6. Clean crankshaft pulley and mating face on crankshaft.
7. Lubricate and install new O-ring seal in crankshaft pulley.
8. Install crankshaft pulley, locking ring and new pulley bolt.
9. Torque tighten crankshaft pulley bolt. Remove special tool (303-1185) from crankcase.
10. Install inspection cover to lower crankcase, install and tighten bolts (x2).
11. Install PAS pump mounting bracket, install and torque tighten Torx bolts (x4).
12. Install PAS pump, install and torque tighten bolts (x3).
13. Install alternator mounting bracket, install and torque tighten Torx bolts (x3).
14. Install alternator, install bolt and nut/bolt and torque tighten
15. Connect battery cable, install and torque tighten nut, secure cover. Connect multiplug.
16. Lubricate seal, install new oil filter.
17. Install oil separator drai n tube clip in bracket.
18. Install oil separator drain tube to timing cover.
19. Install A/C compressor idler pulley, torque tighten bolt.
20. Install alternator idler pulley, torque tighten bolt.
21. Install auxiliary drive belt te nsioner, torque tighten bolt.
22. Install water pump pulley, install bolts (x3).
23. Using a suitable socket ba r, release auxiliary drive belt
tensioner, install drive belt.
24. Torque tighten water pump pulley bolts (x3).
25. Clean coolant manifold and mating faces on cylinder heads.
26. Install new O-ring seals (x2) to coolant manifold.
27. Position coolant manifold, connect temperature sensor
multiplug, install coolant pipe in manifold.
28. Install and torque tighten Torx bolts (x4) that attach the coolant manifold to cylinder heads.
29. Connect coolant hoses (x3) to coolant manifold and
secure clips.
30. Connect engine breather to oil separator.
31. Clean left and right cam covers.
32. Install the right cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
33. Install left cam cover (Refer to ’Left Side Cam Cover -
Remove and Install’, page 3-10-4).
34. Install the engine assembly (refer to Workshop Manual procedure 03.00.AA Engine Assembly - Renew).
Caution
Make sure the cranks haft front oil seal mating faces are
clean and dry.
Caution
Do not remove the crankshaft front oil seal protector
until the oil seal is correctly installed.
If you do, the oil seal can be damaged.
A0310243
A0310245
Caution
The bolt thread in the cran kshaft must be cleaned out
before a new crankshaft pulley retaining bolt is installed.
Note: Check the crankshaft pulley and locking ring for damage.

Power Conversion (03.11)
Engine (03.00)3-11-8 Workshop Manual May 2007
11.Remove and discard oil scavenge pump gasket (see
Figure 5).
Figure 5
12. Remove oil pump(s) drive sprocket.
13. Disconnect multiplug from oil pressure sensor (see Figure 6).
Figure 6
14.Disconnect multiplug from engine electric coolant temperature sensor (see Figure 7).
Figure 7
15. Disconnect multiplug from cr ankshaft timing sensor (see
Figure 8).
Figure 8
A0302276
A030216
A030216A
A030206

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-9
16. Release harness clips (x6) from sump (see Figure 9).
Figure 9
17.Remove bolts (x4) securing LH and RH HEGO sensor
multiplug brackets to sump (see Figure 10).
Figure 10
18. Disconnect multiplug from A/C compressor.
19. Remove bolts (x4) securing A/C compressor to mounting bracket. Remove compressor.
20. Remove bolts (x2) securing inlet and outlet oil pipes to sump (see Figure 11).
Figure 11
21. Release both oil pipes together from sump, remove and discard 'O' ring seals from pipes.
A030206B
A030206C
A030247

Power Conversion (03.11)
Engine (03.00)3-11-12 Workshop Manual May 2007
12. Install piston ring clamp to each piston in turn and install
in its respective cylinder bore. Remove piston ring
clamp (see Figure 19).
Figure 19
13. Lubricate crankshaft journa ls with clean engine oil.
14. Carefully pull each connecting rod into place on each crankshaft journal.
15. Install bearing caps to their relevant connecting rods. Install and torque tighten retaining bolts (x16).
16. Clean windage tray.
17. Install windage tray, install and torque tighten bolts (x8).
18. Clean old sealant from sump flange and engine bedplate.
19. Ensure that sump flange and mating face on engine bedplate are clean and dry.
20. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
21. Ensure that there are no gaps in sealant track.
22. Install sump, install and torque tighten bolts (x16) in the correct sequence.
23. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
24. Lubricate and install new O-ring seals to oil pipes.
25. Install oil pipes in sump, install and torque tighten bolts (x2)
26. Install compressor, install and torque tighten bolts (x4).
27. Connect multiplug to A/C compressor.
28. Install LH and RH HEGO sensor multiplug brackets to sump. Install and torque tighten bolts (x4).
29. Secure harness clips (x6) in sump.
30. Connect multiplug to crankshaft timing sensor.
31. Connect multiplug to engine electric coolant temperature sensor.
32. Connect multiplug to oil pressure sensor.
33. Clean oil scavenge pump and mating face on sump.
34. Install oil pump(s) drive sprocket. 35. Install new oil scavenge pump gasket, align on dowels
(x2).
36. Install chain onto oil scavenge pump sprocket.
37. Install oil scavenge pump, align to dowels (x2), Install
and torque tighten bolts (x3).
38. Install chain onto oil pump drive sprocket.
39. Clean oil pressure pump and mating face on sump.
40. Install new gasket to sump, align to dowels (x2).
41. Position oil pressure pu mp, install chain on pump
sprocket.
42. Install oil pressure pump, align to dowels (x2), Install and
torque tighten bolts (x3).
43. Install chain tensioner, install and torque tighten bolt, remove guide pin.
44. Install crankshaft timing sprocket.
45. Install cylinder head gaskets - engine set (see Workshop Manual procedure 03.01.HW Gasket - Cylinder Head -
Engine Set - Renew Wi th Engine Removed).
Piston-Renew
Removal
1. Remove cylinder head gaskets - engine set (see
Workshop Manual procedure 03.01.HW Gasket -
Cylinder Head - Engine Set - Renew With Engine
Removed).
2. Remove crankshaft timing sprocket from crankshaft.
3. Install guide pin through lower hole on chain tensioner.
4. Remove bolt securing oil pressure pump chain tensioner assembly to engine bedplate (see Figure 1).
Figure 1
Caution
When assembling connecting rods and connecting rod
bearing caps it is imperative that bearing slots and tangs
be located on the same side of the connecting rods.
A0311337
Repair Operation Time (ROT)
ItemCode
Piston-Renew 03.11.CH
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.
A0302274

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-13
5. Remove tensioner assembly (see Figure 2).
Figure 2
6. Remove bolts (x3) securing oil pressure pump to sump.
7. Release chain from oil pressure pump sprocket, remove
oil pump.
8. Remove and discard oil pressure pump gasket.
9. Remove bolts (x3) securing oil scavenge pump to sump
(see Figure 3).
Figure 3
10. Release chain from oil scavenge pump sprocket, remove scavenge pump.
11. Remove and discard oil scavenge pump gasket (see Figure 4).
Figure 4
12. Remove oil pump(s) drive sprocket. 13. Disconnect multiplug from
oil pressure sensor (see
Figure 5).
Figure 5
14. Disconnect multiplug from engine electric coolant
temperature sensor (see Figure 6).
Figure 6
A0302274
A0302274B
A0302276
A030216
A030216A

Power Conversion (03.11)
Engine (03.00)3-11-14 Workshop Manual May 2007
15. Disconnect multiplug from crankshaft timing sensor (see
Figure 7).
Figure 7
16. Release harness clips (x6) from sump (see Figure 8).
Figure 8
17.Remove bolts (x4) securing LH and RH HEGO sensor multiplug brackets to sump (see Figure 9).
Figure 9
18. Disconnect multiplug from A/C compressor.
19. Remove bolts (x4) securing A/C compressor to mounting bracket. Remove compressor (see Figure 10).
Figure 10
A030206
A030206B
A030206C
A0302303

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-17
12. Install piston ring clamp to piston, install piston assembly
in its cylinder bore. Remo ve piston ring clamp (see
Figure 19).
Figure 19
13. Lubricate crankshaft journal with clean engine oil.
14. Carefully pull connecting ro d into place on crankshaft
journal.
15. Install bearing cap to connecting rod. Install and torque tighten retaining bolts (x2).
16. Clean windage tray.
17. Install windage tray, install and torque tighten bolts (x8).
18. Clean old sealant from sump flange and engine bedplate.
19. Ensure that sump flange and mating face on engine bedplate are clean and dry.
20. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
21. Ensure that there are no gaps in sealant track.
22. Install sump, install and torque tighten bolts (x16) in the correct sequence.
23. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
24. Lubricate and install new 'O' ring seals to oil pipes.
25. Install oil pipes in sump, install and torque tighten bolts (x2)
26. Install compressor, install and torque tighten bolts (x4).
27. Connect multiplug to A/C compressor.
28. Install LH and RH HEGO sensor multiplug brackets to sump. Install and torque tighten bolts (x4).
29. Secure harness clips (x6) in sump.
30. Connect multiplug to crankshaft timing sensor.
31. Connect multiplug to engine electric coolant temperature sensor.
32. Connect multiplug to oil pressure sensor.
33. Clean oil scavenge pump and mating face on sump.
34. Install oil pump(s) drive sprocket.
35. Install new oil scavenge pu mp gasket, align on dowels
(x2). 36. Install chain onto oil scavenge pump sprocket.
37. Install oil scavenge pump, align to dowels (x2), Install
and torque tighten bolts (x3).
38. Install chain onto oil pump drive sprocket.
39. Clean oil pressure pump and mating face on sump.
40. Install new gasket to sump, align to dowels (x2).
41. Position oil pressure pump, install chain on pump sprocket.
42. Install oil pressure pump, align to dowels (x2), Install and torque tighten bolts (x3).
43. Install chain tensioner, install and torque tighten bolt, remove guide pin.
44. Install crankshaft timing sprocket.
45. Install cylinder head gaskets - engine set (see Workshop Manual procedure 03.01.HW Gasket - Cylinder Head -
Engine Set - Renew With Engine Removed).
Additional Piston-Renew (Each)
Removal
1. Mark bearing caps and connecting rods for correct installation.
2. Remove bolts (x2) securing bearing cap to connecting rod, remove bearing cap.
3. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal.
4. Carefully push connecting rod/piston assembly upwards and remove from cylinder bore.
5. Remove special tools from connecting rod.
6. Install bearing cap on connecting rod, install and lightly tighten retaining bolts.
7. Remove circlip (x2) securing gudgeon pin in piston and
connecting rod. Remove piston.
Installation
1. Clean cylinder bore.
2. Install piston rings in cylinder bore to a pre-determined depth and measure ring gaps.
3. Remove piston ring set from cylinder bore and install on piston.
4. Clean connecting rod.
5. Install piston on connecting rod in its correct orientation, install circlip(s).
Caution
Install pistons into cylinder block with the ‘arrow’ on the
piston crown facing to the front of the engine.
A0311337
Repair Operation Time (ROT)
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Connecting rod bolts are tor que
tightened to yield and
mu st
be replaced.

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-19
11. Remove and discard oil scavenge pump gasket (see
Figure 4).
Figure 4
12. Remove oil pump(s) drive sprocket.
13. Disconnect multiplug from oil pressure sensor (see
Figure 5).
Figure 5
14. Disconnect multiplug from engine electric coolant temperature sensor (see Figure 6).
Figure 6
15. Disconnect multiplug from cr ankshaft timing sensor (see
Figure 7).
Figure 7
A0302276
A030216
A030216A
A030206