2010.5 Peugeot 508 engine

162
!
Safety
Dynamic stability control (DSC)
Activation
This system is activated automatically each time the vehicle is star ted. It comes into operation in the event of a grip or trajectory problem.
This is indicated by flashing of this warning lamp in the instrument panel.
Deactivation
In exceptional conditions (star ting a vehicle which is bogged down, stuck in snow, on soft ground...), it may be advisable to deactivate the DSC system, so that the wheels can move freely and regain grip.
The DSC system offers exceptional safety in normal driving, but this should not encourage the driver to take extra risks or drive at high speed. The correct operation of the system depends on obser vation of the manufacturer's recommendations regarding the wheels (tyres and rims), the braking components, the electronic components and the PEUGEOT assembly and operation procedures. After an impact, have the system checked by a PEUGEOT dealer
or a qualified workshop.
Operating fault
If this warning lamp comes on, accompanied by an audible signal and a message in the instrument panel screen, this indicates a fault with the system. Contact a PEUGEOT dealer or a qualified workshop to have the system checked.
Reactivation
The system is reactivated automatically each time the ignition is switched back on or from 30 mph (50 km/h).  Press the "ESP OFF" button again to
reactivate it manually.
 Press the "ESP OFF" button.
This warning lamp and the indicator lamp in the button come on: the DSC system no longer acts on the operation of the engine.

164
Safety
Front seat belt height adjustment
 To adjust the anchorage point, squeeze the control A and slide it until you find a notch.
From approximately 12 mph (20 km/h), the warning lamp(s) flash for two minutes accompanied by an audible signal. Once these two minutes have elapsed, the warning lamp(s) remain on until the driver or one or more passengers fasten their seat belt.
Seat belt not fastened/unfastened warning lamps
1. Front and/or rear seat belts not fastened/unfastened warning lamp in the instrument panel. 2. Front left seat belt warning lamp. 3. Front right seat belt warning lamp. 4. Rear right seat belt warning lamp. 5. Rear centre seat belt warning lamp. 6. Rear left seat belt warning lamp.
Front seat belt warning lamps
On switching on the ignition, warning lamp 1 comes on in the instrument panel and the corresponding warning lamp 2 and/or 3 come(s) on in red in the passenger's seat belt and front airbag warning lamp display if the corresponding seat
belt is not fastened or is unfastened.
Rear seat belt unfastened warning lamps
On switching on the ignition, with the engine running or the vehicle at a speed below around 12 mph (20 km/h), the corresponding warning lamps 4 , 5 or 6 comes on in red for about 30 seconds if a seat belt is not fastened. Above 12 mph (20 km/h), the corresponding warning lamps 4 , 5 and 6 comes on in red, accompanied by an audible signal and a message in the instrument panel screen, when a rear passenger has unbuckled their seat belt.

172
!i
Practical information
1. Sealing
 Switch off the ignition.  Turn the selector A to the "SEALANT" position.  Check that the switch B is in position "O" .
 Uncoil the white pipe G fully.  Unscrew the cap from the white pipe.  Connect the white pipe to the valve of the tyre to be repaired.
 Connect the compressor's electric plug to the vehicle's 12 V socket.  Star t the vehicle and leave the engine running.
Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if swallowed and causes irritation to the eyes. Keep it out of reach of children.
Avoid removing any foreign bodies which have penetrated into the tyre.

174
!
Practical information
2. Infl ation
 Turn the selector A to the "AIR" position.  Uncoil the black pipe H fully.  Connect the black pipe to the valve of the wheel.
 Connect the compressor's electric plug to the vehicle's 12 V socket.  Star t the vehicle again and leave the engine running.
 Adjust the pressure using the compressor (to inflate: switch B in position "I" ; to deflate: switch B in position "O" and press button C ), in accordance with the vehicle's tyre pressure label (located on the left hand door aper ture).
A loss of pressure indicates that the puncture has not been fully plugged; contact a PEUGEOT dealer or qualified
workshop for assistance.  Remove and stow the kit.  Drive at reduced speed (50 mph [80 km/h] max) limiting the distance travelled to approximately 120 miles (200 km).
 Visit a PEUGEOT dealer or a qualified workshop as soon as possible. You must inform the technician that you have used this kit. After
inspection, the technician will inform you whether the tyre can be repaired or must be replaced.

8175
!
Practical information
Removing the cartridge
 Stow the black pipe.  Detach the angled base from the white pipe.  Suppor t the compressor ver tically.  Unscrew the car tridge from the bottom.
Beware of discharges of fluid. The expiry date of the fluid is indicated on the car tridge. The sealant car tridge is designed for
single use; even if only par tly used, it must be replaced. After use, do not discard the car tridge into the environment, take it to an authorised waste disposal site or a PEUGEOT dealer. Do not forget to obtain a new sealant car tridge, available from PEUGEOT dealers or from a qualified workshop.
Checking tyre pressures/
inflating accessories
You can also use the compressor, without injecting any product, to: - check or adjust the pressure of your tyres, - inflate other accessories (balls, bicycle tyres...).
 Turn the selector A to the "Air" position.  Uncoil the black pipe H fully.  Connect the black pipe to the valve of the wheel or accessory. If necessary, fit one of the adaptors supplied with the kit first.
 Connect the compressor's electrical connector to the vehicle's 12 V socket.  Star t the vehicle and let the engine run.  Adjust the pressure using the compressor (to inflate: switch B in position "I" ; to deflate: switch B in position "O" and press button C ), according to the vehicle's tyre pressure label or the accessory's pressure label.  Remove the kit then stow it.

8195
Practical information
Engine compartment fuses
Access to the fuses
 Unclip the cover.  Change the fuse (see corresponding paragraph).
 When you have finished, close the cover carefully to ensure correct sealing of the fusebox.
Fuse N° Rating (A) Functions
F2015 Front /rear screenwash pump.
F2120 Headlamp wash pump.
F2215 Horn.
F2315 Right-hand main beam headlamp.
F2415 Left-hand main beam headlamp.
F275 Left hand lamp mask.
F285 Right hand lamp mask. The fusebox is placed in the engine compar tment near the battery.

196
i
!
!
Practical information
12 V battery
Procedure for charging your battery when it is flat or for star ting the engine using another battery.
The presence of this label indicates the use of a 12 V lead-acid battery with special technology and specification, for which the involvement of a PEUGEOT dealer or qualified workshop is required when replacing or disconnecting the battery. Failure to obser ve this recommendation may cause premature wear of the battery.
After refitting the battery, the Stop & Star t system will only be active after several hours depending on the climatic conditions and the state of charge of the battery (up to about 8 hours).
The battery is located under the bonnet. To gain access to it:  open the bonnet using the interior release lever, then the exterior safety catch,  remove the plastic cover to gain access to the two terminals,  unclip the fusebox to remove the battery, if necessary.
Access to the battery
 Raise the locking tab fully.
Disconnecting the cables
Reconnecting the cables
 Position the open clip 1 of the cable on the positive terminal (+) of the battery.  Press ver tically on the clip 1 to position it correctly against the battery.  Lock the clip by spreading the positioning
lug and then lowering the tab 2 .
Do not force the tab as locking will not
be possible if the clip is not positioned correctly; star t the procedure again.

8197
i
Practical information
 Connect the red cable to the positive terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B .
Starting using another
battery
 Disconnect the battery from the vehicle.  Follow the instructions for use provided by the manufacturer of the charger.  Reconnect star ting with the negative terminal (-).  Check that the terminals and connectors are clean. If they are covered with sulphate (whitish or greenish deposit), remove them and clean them.
Charging the battery using
a battery charger
The Stop & Star t battery does not have to be disconnected for charging.
 Connect one end of the green or black cable to the negative terminal (-) of the slave battery B .  Connect the other end of the green or black
cable to the ear th point C on your vehicle (engine mounting).  Operate the star ter, let the engine run.  Wait until the engine returns to idle and
disconnect the cables.