2010.5 Peugeot 508 lock

121
!
Instruments and controls
Indicator and warning lamps
Visual indicators informing the driver that a system is in operation, switched off or has a fault.
When the ignition is switched on
Cer tain warning lamps come on for a few
seconds in the instrument panel and/or instrument panel screen when the vehicle's ignition is switched on. When the engine is star ted, these same warning lamps should switch off. If they remain on, before moving off, refer to the information on the warning lamp concerned.
Associated warnings
The switching on of cer tain warning lamps may be accompanied by an audible signal and a message in the instrument panel screen. The warning lamps may come on continuously (fixed) or flash.
Cer tain warning lamps may come on in one of two modes. Only by relating the type of lighting to the operating status of the vehicle can it be ascer tained whether the situation is normal or whether a fault has occurred.
1
2
2
2
3
3
3
2
3
3
With the vehicle stationar y , use the left hand ar ythumb wheel to move through the menus, so as to configure the vehicle settings (driving and comfor t systems, ...). - Rotation (other than menu): scroll through the list of active functions available, - Press: main menu, confirm the selection, - Rotation (in a menu): move up or down in the menu.
Main menu
Vehicle settings
Screen settings
Preheating/Preventilation
Driving position setting
Unlocking boot only
Driving assistance
Speeds memorised
Rear wipe in reverse gear
Automatic parking brake
Lighting
Welcome lighting
Guide-me-home headlamps
Directional headlamps
Settings
Language
Units
Fuel consumption
Temperature
Colours
3
1
2
2
3
2
3
1
2

28
Instruments and controls
is onCauseAction/Obser vations
Dynamic stability control (ESP/ASR)
flashing. The ESP/ASR regulation is active. The system optimises traction and improves the directional stability of the vehicle.
fixed. Unless it has been deactivated with the indicator lamp in the button on, the ESP/ASR system has a fault.
Have it checked by a PEUGEOT or a qualified workshop.
Engine autodiagnosis system
fixed. The emission control system has a fault. The warning lamp should go off when the engine is started. If it does not go off, contact a PEUGEOT dealer or qualified workshop urgently.
flashing. The engine management system has a fault. Risk of destruction of the catalytic conver ter. Have it checked by a PEUGEOT dealer or a qualified workshop.
Low fuel level fixed with the needle in the red zone. When it first comes on there remains approximately 7 litres of fuel in the tank.
At this point, you begin to use the fuel reser ve.
Refuel as soon as possible to avoid running out of fuel. This warning lamp will come on every time the ignitio n
is switched on, until a sufficient addition of fuel is made. Never continue to drive until you run out of fuel, as this could damage the emission control and injection systems.
Anti-lock Braking System (ABS)
fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking. Drive carefully at reduced speed and contact a PEUGEOT dealer or a qualified workshop without delay.

34
i
i
Instruments and controls
For 5 seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 186 miles (300 km). For 5 seconds after the ignition is switched on, the screen indicates:
The distance remaining may be weighted by the time factor, depending on the driving conditions. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account.
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows:  switch off the ignition,  press and hold the trip distance recorder zero reset button,
 switch on the ignition; the distance recorder display begins a countdown,
 when the display indicates "=0" , release the button; the spanner disappears.
Retrieving the service information
You can access the ser vice information at any time.  Press the trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, then disappears.

239
i
Access
System which permits central unlocking or locking of the vehicle using the lock or from a distance. It is also used to locate and star t the vehicle, as well as providing protection against theft.
Remote control key
Unfolding the key
 First press this button to unfold the key.
"Keyless Entry and
Starting" system
System that allows the opening, closing and star ting of the vehicle while keeping the electronic key on your person. It can also be used as a remote control.
Unlocking the vehicle
Complete unlocking
Using the key
 Turn the key to the front of the vehicle to unlock the vehicle.
Using the remote control
 Press the open padlock to unlock the vehicle. Holding this button down opens the windows automatically.
Using the electronic key
 With the electronic key on your person and in the defined zone, pass your hand behind the door handle to unlock the vehicle, then pull on the handle to open the door. Your passengers can also open their doors, as soon as the electronic key is in the defined zone around the vehicle.
Unlocking is confirmed by rapid flashing of the direction indicators for approximately two seconds.
According to version, the door mirrors unfold at the same time.

40
i
Access
Selective unlocking
 To unlock the driver's door only press the open padlock once.
Using the remote control
This is set via the instrument panel screen configuration menu. Complete unlocking is activated by default.
Using the electronic key
 To unlock only the driver's door with the electronic key on your person, pass your hand behind the driver's door handle then pull the handle to open the door.  To unlock the vehicle completely, pass your hand behind one of the passenger door
handles, on the side of the vehicle where the electronic key is located, then pull the door handle.
Each unlocking is confirmed by rapid flashing of the direction indicators for approximately two seconds. According to version, the door mirrors unfold at the same time as the first unlocking action.
Unlocking the boot
Using the remote control
 Press this button to unlock the vehicle and open the boot.
Using the electronic key
 With the electronic key in the defined zone,
press button 1 (Saloon) or lift lever 2 (SW) to unlock the vehicle and open the boot.
 To unlock the other doors and the boot, press the open padlock again

241
!
Access
Boot only function activated
This is set in the instrument panel configuration menu.
This function is deactivated by default.  use of the remote control or the electronic key then unlocks and/or opens only the boot.
Don't forget to lock your boot after wards.
Locking the vehicle
Normal locking
Using the key
 Turn the key towards the rear of the vehicle to lock the vehicle completely.
Using the remote control
 Press the closed padlock to lock the vehicle completely.
Using the electronic key
 With the electronic key in the defined zone, press with a finger on the door handle (at the markings) to lock the vehicle.  From the boot (SW only), with the electronic key in the defined zone, press a button to lock the vehicle.

42
i
!
i!
Access
As a safety measure (children on board), never leave the vehicle without taking your key, even for a shor t period.
Guard against theft when the electronic key is in the defined zone with the vehicle unlocked.
Maintaining any locking action automatically closes the windows and sunroof. Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds. According to version, the door mirrors fold at the same time.
If one of the doors or the boot is still open or if an electronic key has been left inside the vehicle, the central locking does not take place. When the vehicle is locked, if it is unlocked inadver tently, it will relock automatically after about thir ty seconds unless a door is opened.
It is not possible to lock the vehicle if an electronic key is left inside the vehicle. After a long period of parking, the automatic detection functions of the electronic key are inhibited so as to not discharge the vehicle's battery. You should then use the remote control function of the electronic key to unlock the vehicle.
The folding and unfolding of the door mirrors by the remote control can be deactivated by a PEUGEOT dealer.
Deadlocking
Deadlocking renders the exterior and interior door controls inoperative. It also deactivates the manual central control button. Therefore, never leave anyone inside the vehicle when it is deadlocked.
Using the key
 Turn the key to the rear in the driver's door lock to lock the vehicle completely.  Turn the key to the rear again within five seconds to deadlock the vehicle.

243i
Access
lighting of the direction indicators for approximately two seconds.
Using the remote control
 Press the closed padlock to lock the vehicle completely or press the closed padlock for more than two seconds to close the windows automatically in addition to locking.
Using the electronic key
By the doors:  With the electronic key in the defined zone, press a finger on the door handle (at the markings) to lock the vehicle.  Within five seconds, press the door handle again to deadlock the vehicle.
By the tailgate (SW only):  With the electronic key in the defined zone, press the button to lock the vehicle.  Within five seconds, press the button to deadlock the vehicle.
 Press the closed padlock again within five seconds to deadlock the vehicle.