Page 131 of 330
4119
i
!
Driving
With the engine running, press button 1 to activate the system and deploy the strip. Press and hold button 2 to deactivate the system and retract the strip. The activated/deactivated state is saved and restored on restar ting the engine.
Activation/Deactivation
With the engine running, adjust the brightness of the information displayed using buttons 3 : - the "sun" to increase the brightness, - the "moon" to decrease the brightness.
Brightness adjustment
We recommend that adjustments are made using these buttons only when the vehicle is stationary. When stationary or while driving, no
objects should be placed around the strip (or in its recess) so as to not impede deployment of the strip and its correct operation.
In cer tain extreme weather conditions (rain and/or snow, bright sunshine, ...) the head-up display may not be legible or may suffer temporary inter ference. Cer tain glasses (sunglasses, spectacles or polarised lenses) may hamper reading of the information. To clean the strip, which is made of organic glass, use a clean, soft cloth (such as a spectacles cloth or microfibre cloth). Do not use a dry or abrasive cloth or detergent or solvent products as these could scratch the strip or damage the non-reflective coating.
Height adjustment
With the engine running, adjust the display to the desired height using buttons 4 : - up to move the display up,
- down to move the display down.
Page 150 of 330
5
137
i
!
Visibility
Manual adjustment
of halogen
headlamps Automatic adjustment of xenon headlamps
To avoid causing a nuisance to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats. -. 3 people. 1. 5 people. -. Intermediate setting. 2. 5 people + maximum authorised load. -. Intermediate setting. 3. Driver + maximum authorised load.
The initial setting is position "0" .
If a fault occurs, this warning lamp is displayed in the instrument panel, accompanied by an audible signal and a message in the instrument panel screen. The system then places your headlamps in the lowest position.
In order to avoid causing a nuisance to other road users, this system corrects the height of the xenon headlamps beam automatically and when stationary, in relation to the load in the vehicle.
If a fault occurs, do not touch the xenon bulbs. Contact a PEUGEOT dealer or a qualified workshop.
Page 177 of 330
164
Safety
Front seat belt height adjustment
To adjust the anchorage point, squeeze the control A and slide it until you find a notch.
From approximately 12 mph (20 km/h), the warning lamp(s) flash for two minutes accompanied by an audible signal. Once these two minutes have elapsed, the warning lamp(s) remain on until the driver or one or more passengers fasten their seat belt.
Seat belt not fastened/unfastened warning lamps
1. Front and/or rear seat belts not fastened/unfastened warning lamp in the instrument panel. 2. Front left seat belt warning lamp. 3. Front right seat belt warning lamp. 4. Rear right seat belt warning lamp. 5. Rear centre seat belt warning lamp. 6. Rear left seat belt warning lamp.
Front seat belt warning lamps
On switching on the ignition, warning lamp 1 comes on in the instrument panel and the corresponding warning lamp 2 and/or 3 come(s) on in red in the passenger's seat belt and front airbag warning lamp display if the corresponding seat
belt is not fastened or is unfastened.
Rear seat belt unfastened warning lamps
On switching on the ignition, with the engine running or the vehicle at a speed below around 12 mph (20 km/h), the corresponding warning lamps 4 , 5 or 6 comes on in red for about 30 seconds if a seat belt is not fastened. Above 12 mph (20 km/h), the corresponding warning lamps 4 , 5 and 6 comes on in red, accompanied by an audible signal and a message in the instrument panel screen, when a rear passenger has unbuckled their seat belt.
