2010.5 Peugeot 206 P Dag buttons
[x] Cancel search: buttonsPage 43 of 119
i
!
44
KEYS
Central locking and unlocking
From the front doors, the keys allow you
to lock and unlock the doors and boot.
If one of the doors is open, the central
locking does not work.
If the boot is open, the central locking
works.
Remote control
This carries out the same functions as
the key, from a distance. Locking
Press button
A to lock the vehicle.
T h i s i s c o n fi r m e d b y fi x e d l i g h t i n g o f t h e
d i r e c t i o n i n d i c a t o r s f o r a p p r o x i m a t e l y
two seconds.
Unlocking
Press button B to unlock the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators. Starting the vehicle
There are four possible positions of the
key in the ignition switch:
1. STOP position:
the ignition is off.
2. 1 st notch, Accessories position:
the ignition is off but the accessories can operate.
3. 2nd notch, On position:
the ignition is on.
4. Starting position:
the starter is operated.
Avoid pressing the buttons of your
remote control out of range of your
vehicle as this could stop it from
working. The remote control would
then have to be reinitialised (refer
to the corresponding section).
A heavy object (key ring, etc.), at-
tached to the key and weighing
down on its shaft in the switch,
may cause a malfunction.
Page 44 of 119
!
46
Keys
Make a careful note of the number of each key. This number is coded on the
label attached to the key.
Remote control
The high frequency remote control is a sensitive system; do not o perate
it while it is in your pocket as there is a possibility that i t may unlock the
vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and
out of sight of your vehicle. You run the risk of stopping it from working and
the remote control would have to be reprogrammed.
The remote control does not operate when the key is in the ignition, even
w h e n t h e i g n i t i o n i s s w i t c h e d o f f , e x c e p t f o r r e i n i t i a l i s a t i o n . Do not throw the remote control bat-
teries away, they contain metals which
are harmful to the environment.
Take them to an approved collection
point.
Locking the vehicle
Driving with the doors locked may make access to t he passenger compartment
b y t h e e m e r g e n c y s e r v i c e s m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children on board), remove the key fro m the
ignition when you leave the vehicle, even for a short time.
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a t i o n s t o t h e e l e c t r o n i c e n g i n e i m m o b i l i s e r s y s t e m ,
this could cause malfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a PEUGEOT dealer, to ensure that the
keys in your possession are the only ones which can start the vehicle .
Lost keys
V i s i t a P E U G E O T d e a l e r w i t h t h e v e h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u m e n t s .
The PEUGEOT network will be able to retrieve the key code and the
transponder code to order a replacement key.
Page 45 of 119
i
!
44
KEYS
Central locking and unlocking
From the front doors, the keys allow you
to lock and unlock the doors and boot.
If one of the doors is open, the central
locking does not work.
If the boot is open, the central locking
works.
Remote control
This carries out the same functions as
the key, from a distance. Locking
Press button
A to lock the vehicle.
T h i s i s c o n fi r m e d b y fi x e d l i g h t i n g o f t h e
d i r e c t i o n i n d i c a t o r s f o r a p p r o x i m a t e l y
two seconds.
Unlocking
Press button B to unlock the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators. Starting the vehicle
There are four possible positions of the
key in the ignition switch:
1. STOP position:
the ignition is off.
2. 1 st notch, Accessories position:
the ignition is off but the accessories can operate.
3. 2nd notch, On position:
the ignition is on.
4. Starting position:
the starter is operated.
Avoid pressing the buttons of your
remote control out of range of your
vehicle as this could stop it from
working. The remote control would
then have to be reinitialised (refer
to the corresponding section).
A heavy object (key ring, etc.), at-
tached to the key and weighing
down on its shaft in the switch,
may cause a malfunction.
Page 47 of 119
!
46
Keys
Make a careful note of the number of each key. This number is coded on the
label attached to the key.
Remote control
The high frequency remote control is a sensitive system; do not o perate
it while it is in your pocket as there is a possibility that i t may unlock the
vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and
out of sight of your vehicle. You run the risk of stopping it from working and
the remote control would have to be reprogrammed.
The remote control does not operate when the key is in the ignition, even
w h e n t h e i g n i t i o n i s s w i t c h e d o f f , e x c e p t f o r r e i n i t i a l i s a t i o n . Do not throw the remote control bat-
teries away, they contain metals which
are harmful to the environment.
Take them to an approved collection
point.
Locking the vehicle
Driving with the doors locked may make access to t he passenger compartment
b y t h e e m e r g e n c y s e r v i c e s m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children on board), remove the key fro m the
ignition when you leave the vehicle, even for a short time.
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a t i o n s t o t h e e l e c t r o n i c e n g i n e i m m o b i l i s e r s y s t e m ,
this could cause malfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a PEUGEOT dealer, to ensure that the
keys in your possession are the only ones which can start the vehicle .
Lost keys
V i s i t a P E U G E O T d e a l e r w i t h t h e v e h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u m e n t s .
The PEUGEOT network will be able to retrieve the key code and the
transponder code to order a replacement key.
Page 78 of 119
!
73
Programming
Turn dial 1 to the "CRUISE" po-
sition: the cruise control mode is
selected but is not switched on
(OFF).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed
s p e e d r e s u l t s i n fl a s h i n g o f t h i s s p e e d o n t h e d i s p l a y .
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically ca n-
c e l s t h e fl a s h i n g o f t h e s p e e d .
Return to normal driving
Turn dial 1 to the "0" position: the cruise control mode is
deselected. The display returns to the distance rec order.
Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
Switch off the cruise control by pressing button 4 : the
d i s p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( O F F ) .
Switch the cruise control back on by pressing button 4
again.
You can then change the programmed speed using but
tons 2
and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press. Operating fault
In the event of a cruise control malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have it checked by a PEUGEOT dealer.
When the cruise control is switched
on, be careful if you maintain the
pressure on one of the programmed
speed changing buttons: this may
result in a very rapid change in the
speed of your vehicle.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f fi c .
On a steep descent, the cruise
control will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi-tioned correctly,
-
n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Page 113 of 119
10
107
Button
Function
A
Radio On/Off.
B - Decrease volume.
C + Increase volume.
D
C D e j e c t .
E RDS * RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
F TA * T r a f fi c i n f o r m a t i o n p r i o r i t y o n / o f f .
Press for more than 2 seconds: PTY function on/off.
G
Setting of the bass, treble, loudness, sound distribution a
nd automatic volume correction.
H
Increase the setting of the functions associated with butto
n G .
I
Decrease the setting of the functions associated with butto
n G .
J
M a n u a l a n d a u t o m a t i c s e a r c h o f h i g h e r f r e q u e n c i e s .
S e l e c t i o n o f t h e n e x t t r a c k o n t h e C D a n d o f t h e P T Y ( r a d i o ) .
K MAN Manual/automatic operation of buttons J and L .
L
M a n u a l a n d a u t o m a t i c s e a r c h o f l o w e r f r e q u e n c i e s .
S e l e c t i o n o f t h e p r e v i o u s t r a c k o n t h e C D a n d o f t h e P T Y ( r a d i
o ) .
M CH. CD S e l e c t i o n o f t h e C D c h a n g e r s o u r c e .
Press for more than 2 seconds: random play.
N CD S e l e c t i o n o f t h e C D s o u r c e .
Press for more than 2 seconds: random play.
O Radio Selection of the radio source. Selection of the FM1, FM2, FMAST
, AM wavebands.
Press for more than 2 seconds: automatic storing of stations (autosto re).
1 to 6 1 2 3 4 5 6 Selection of the stored station.
Press for more than 2 seconds: storing of a station.
* According to destination country.
Page 114 of 119
10
108
GENERAL FUNCTIONS
On/off
W i t h t h e i g n i t i o n k e y i n
the accessories position
or with the ignition on,
press button A to switch
t h e a u d i o e q u i p m e n t o n
or off.
Anti-theft system
T h e a u d i o e q u i p m e n t i s c o d e d i n s u c h
a way that it can only operate in your
v e h i c l e . I t w o u l d n o t w o r k i f fi t t e d i n a n -
other vehicle.
The anti-theft system is automatic
and requires no action on your part.
Press button C to increase the audio
e q u i p m e n t v o l u m e o r b u t t o n B to de-
crease it.
A continuous press of buttons B and C
adjusts the volume gradually.
AUDIO SETTINGS
Press button G several
times in succession to
access the bass (BASS) ,
treble (TREB) , loudness
(LOUD) , fader (FAD) ,
balance (BAL) and auto-
matic volume correction
settings.
E x i t f r o m a u d i o m o d e
is automatic after a few
seconds without any action or by press-
ing button G f o l l o w i n g c o n fi g u r a t i o n o f
the automatic volume correction. Adjusting the bass
When "BASS" is dis-
played, press button H
or I to change the setting.
- "BASS -9" for a mini-
mum bass setting,
- "BASS 0" for a stan-
dard setting,
- "BASS +9" f o r a m a x i m u m b a s s
setting.
Adjusting the treble
When "TREB" is displayed, press but-
ton H or I to change the setting.
- "TREB -9" for a minimum treble
setting,
- "TREB 0" for a standard setting,
- "TREB +9" f o r a m a x i m u m t r e b l e
setting.
Adjusting the loudness (LOUD)
This function automatically emphasises
bass and treble tones.
Press button H or I to switch the func-
tion on or off.
Note: bass, treble and loudness set-
t i n g s a r e s p e c i fi c t o e a c h s o u r c e . T h e y
can be set differently for the radio
o r C D .
The audio equipment can operate for
30 minutes without the ignition being
switched on.
Page 117 of 119
10
110
Automatic station search
Press button J or L b r i e fl y t o l i s t e n t o
the station immediately above or below.
By continuing to press the button in the
direction selected, you will obtain con-
t i n u o u s s c r o l l i n g o f t h e f r e q u e n c i e s .
T h e s c r o l l i n g s t o p s a t t h e fi r s t s t a t i o n
found when the button is released.
If the TA t r a f fi c i n f o r m a t i o n p r o g r a m m e
is selected, only stations broadcasting
this type of programme are selected.
S e a r c h i n g f o r a s t a t i o n t a k e s p l a c e fi r s t
in "LO" sensitivity (selection of the most
powerful transmitters) during scanning
of the waveband, then in "DX" sensitiv-
i t y ( s e l e c t i o n o f t h e w e a k e s t a n d m o s t
distant transmitters).
To carry out a "DX" sensitivity search
directly, press button J or L twice. Manual station search
Press the
"MAN" button.
Press button J or L b r i e fl y t o i n c r e a s e o r
d e c r e a s e t h e f r e q u e n c y d i s p l a y e d .
By continuing to press the button in the
direction selected, you will obtain con-
t i n u o u s s c r o l l i n g o f t h e f r e q u e n c y .
The scrolling stops as soon as the but-
ton is released.
Pressing the "MAN" button again re-
turns you to the automatic station
search.
Manual storing of stations
S e l e c t t h e s t a t i o n r e q u i r e d .
Press one of the buttons "1" to "6" for
more than two seconds.
The sound stops then becomes audible
a g a i n , c o n fi r m i n g t h a t t h e s t a t i o n h a s
been stored. Automatic storing of FM stations
(autostore)
Press button O for more
than two seconds.
Recalling stored stations
On each waveband, press one of the
buttons "1" to "6" b r i e fl y t o r e c a l l t h e
corresponding stored station.
Your radio automatically stores the
6 stations with the strongest signal on
FM . These stations are stored on the
FMast waveband.
I f i t i s n o t p o s s i b l e t o fi n d s i x s t a t i o n s , t h e
unused memories remain unchanged.