Page 81 of 222
i
i
73
VISIBILITY
The lighting time varies according
to the circumstances:
- when the ignition is off, approxi- mately ten minutes,
- in energy economy mode, ap- proximately thirty seconds,
- when the engine is running, no limit.
This comes on automatically when the
boot is opened and switches off auto-
matically when the boot is closed. Torch
This is a removable lamp, incorporated
in the boot wall, which can be used to
illuminate the boot or as a torch.
BOOT LAMP Use
Extract the torch from its location by
pulling it from the front.
Press the switch, located on the
back, to switch the torch on or off.
Unfold the support, located on the
back, to set down and raise the
torch; for example, when changing
a wheel.
Storing
Put the torch back in place in its lo-
cation starting with the rear.
If you have forgotten to switch off the torch, this switches it off auto-
matically.
It the torch is not engaged correctly, it
may not charge and may not come on
when the boot is opened.
Operation
This torch operates with NiMH type
power packs.
It has a battery life of approximately
45 minutes and charges while you are
driving.
O b s e r v e t h e p o l a r i t i e s w h e n fi t t i n g
the power packs.
Never replace the power packs
with batteries.
Page 90 of 222
80
FITTINGS Opening
Lower the storage shelf.
P r e s s t h e fl a p o p e n i n g c o n t r o l .
L o w e r t h e fl a p .
C h e c k t h a t t h e a d j u s t a b l e b o o t fl o o r
is in the high position.
L o w e r t h e fl a p i n t h e b e n c h s e a t b y
pulling at the top.
Load the objects from inside the
boot.
Ski flap
Device for storing and transporting long
objects.
When unfolded, this provides a storage
area split into 2 sections, completing
the storage spaces available at the rear
of the vehicle.
Storage tray
Page 92 of 222
80
FITTINGS Opening
Lower the storage shelf.
P r e s s t h e fl a p o p e n i n g c o n t r o l .
L o w e r t h e fl a p .
C h e c k t h a t t h e a d j u s t a b l e b o o t fl o o r
is in the high position.
L o w e r t h e fl a p i n t h e b e n c h s e a t b y
pulling at the top.
Load the objects from inside the
boot.
Ski flap
Device for storing and transporting long
objects.
When unfolded, this provides a storage
area split into 2 sections, completing
the storage spaces available at the rear
of the vehicle.
Storage tray
Page 93 of 222
81
FITTINGS
Boot fittings
1. Storage net on right-hand boot trim.
2. Open storage compartments.
3. Torch.
4. A d j u s t a b l e b o o t fl o o r .
5. Carrier bag hook.
6. Securing rings.
7. Storage area under boot carpet
8. Rear parcel shelf.
Page 94 of 222
i
82
FITTINGS
2-position adjustable boot
T h e t w o - p o s i t i o n a d j u s t a b l e b o o t fl o o r
allows you to:
- maximise the volume of the boot,
- partition the boot (stowing the rear shelf...),
- o b t a i n a fl a t fl o o r f r o m t h e b o o t o p e n - ing to the front seats, when the rear
bench seat is in the folded and fully
back position. P l a c i n g t h e a d j u s t a b l e b o o t fl o o r i n
the low position
L i f t t h e a d j u s t a b l e b o o t fl o o r b y p u l l -
ing on the strap.
M o v e t h e a d j u s t a b l e b o o t fl o o r r e a r -
wards and then down, following the
guides on the sides. P l a c i n g t h e a d j u s t a b l e b o o t fl o o r i n
the high position
L i f t t h e a d j u s t a b l e b o o t fl o o r b y p u l l -
ing the strap.
M o v e t h e a d j u s t a b l e b o o t fl o o r r e a r -
wards then up to its high position.
In the high position, the adjustable boot
fl o o r a l l o w s s t o w i n g o f t h e r e a r p a r c e l
shelf and fragile objects.
T h e a d j u s t a b l e b o o t fl o o r i s fi t t e d w i t h
four stowing rings to secure your loads
using the net available as an accessory.
Ensure that your boot is empty be-
fore handling the adjustable boot
fl o o r .
Page 95 of 222
83
FITTINGS
Hooks Rear parcel shelf
This consists of three sections.
T h e f r o n t s e c t i o n i s fl e x i b l e , a n d t h e
central and rear sections are rigid.
The rear section is secured to the tail-
gate by two cords.
To remove it from the boot:
unhook the two cords,
gently lift up the cover to remove it
f r o m i t s fi x i n g s ,
remove the cover.
It can be stored under the adjustable
b o o t fl o o r , i f t h i s i s i n i t s h i g h p o s i t i o n .
The hooks can be used to hold shop-
ping bags.
Page 138 of 222
i
123
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed under the boot
fl o o r .
For access to them:
open the boot,
r e m o v e t h e b o o t fl o o r ,
lift up the boot carpet,
r e m o v e t h e b o x c o n t a i n i n g t h e t o o l s ,
r e m o v e t h e p o l y s t y r e n e s t o r a g e b o x . A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
vehicle. Do not use them for other
purposes.
List of tools
Other accessories
6. Removable towing eye.
Refer to the paragraph "Towing the vehicle".
Access to the tools
Wheel with trim
When removing the wheel , fi r s t
detach the trim using the wheel-
brace 1 pulling at the valve passage
hole.
W h e n r e fi t t i n g t h e w h e e l , r e fi t t h e
trim starting by placing its notch fac-
ing the valve and press around its
edge with the palm of your hand.
1. Wheelbrace.
For removing the wheel trim and r e m o v i n g t h e w h e e l fi x i n g b o l t s .
2. Jack with integral handle.
For raising the vehicle.
3. "Bolt cover" tool.
For removing the bolt protectors ( c o v e r s ) o n a l l o y w h e e l s .
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
4. Centring guide.
F o r r e fi t t i n g a n a l l o y w h e e l t o t h e hub.
5. Socket for the security bolts
( l o c a t e d i n t h e g l o v e b o x ) .
For adapting the wheelbrace to the special "security" bolts (if
y o u r v e h i c l e h a s t h e m ) .
Page 139 of 222
i
124
PRACTICAL INFORMATION
Fitting the steel or "space-
saver" type spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y
wheels, it is normal to notice, when
t i g h t e n i n g t h e b o l t s o n fi t t i n g , t h a t
the washers do not come into con-
tact with the steel or "space-saver"
type spare wheel. The wheel is
secured by the conical contact of
each bolt.
Access to the spare wheel
The spare wheel is installed in the boot
u n d e r t h e fl o o r .
According to country, the spare wheel
may be steel or of the "space-saver"
type.
For access to it, refer to the paragraph
"Access to tools" on the previous page.
Taking out the wheel
Unscrew the yellow central bolt, and
remove it.
Raise the spare wheel towards you
from the rear.
Take the wheel out of the boot.
Putting the wheel back in place
Put the wheel back in its housing.
R e fi t t h e y e l l o w c e n t r a l b o l t i n t h e
centre of the wheel.
Tighten fully until the central bolt
clicks to retain the wheel correctly.
P u t t h e p o l y s t y r e n e s t o r a g e b o x
back in place.
P u t t h e b o x b a c k i n p l a c e a n d c l i p i t .
