2009 YAMAHA T105 lock

PERIODIC MAINTENANCE AND ADJUSTMENT
6-19
6 6. Install the check hole cap.
7. If the drive chain slack is incorrect,
adjust it as follows.
EAU37693
To adjust the drive chain slack
1. Loosen the brake pedal free play
adjusting nut and the brake torque
rod nut.2. Loosen the axle nut, then loosen
the locknut at each end of the
swingarm.
3. To tighten the drive chain, turn the
drive chain slack adjusting nut at
each end of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting nut at each end
of the swingarm in direction (b),
and then push the rear wheel for-
ward. NOTICE: Improper drive
chain slack will overload the en-
gine as well as other vital parts
of the motorcycle and can leadto chain slippage or breakage.
To prevent this from occurring,
keep the drive chain slack with-
in the specified limits.
[ECA10571]
TIPUsing the alignment marks on each
side of the swingarm, make sure that
both chain pullers are in the same posi-tion for proper wheel alignment.
4. Tighten both locknuts, and then
tighten the axle nut and brake
torque rod nut to their specified
torques.
1. Drive chain slackDrive chain slack:
25.0–35.0 mm (0.98–1.38 in)
1
1. Brake pedal free play adjusting nut
2. Locknut
3. Drive chain slack adjusting nut
4. Axle nut
5. Brake torque rod nut
1
2
3
4
5
1. Alignment marks
2. Drive chain slack adjusting nut
3. Locknut
4. Chain puller
14
2
3
(a)
(b)
U40BE0E0.book Page 19 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
6
EAU47760
Replacing a headlight bulb If a headlight bulb burns out, replace it
as follows.NOTICE
ECA10650
Take care not to damage the follow-
ing parts:

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.


Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of awattage higher than specified.
1. Remove cowling A. (See page
6-6.)
2. Remove the headlight bulb cover.3. Remove the headlight bulb holder
(together with the bulb) by turning
it counterclockwise.
4. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.5. Place a new bulb into the holder,
push it in, and then turn it clock-
wise until it stops.
6. Install the bulb holder (together
with the bulb) by turning it clock-
wise.
7. Install the headlight bulb cover.
8. Install the cowling.
9. Have a Yamaha dealer adjust the
headlight beam if necessary.
1. Headlight bulb cover
1. Headlight bulb holder
2. Headlight bulb
1
1
2
1. Do not touch the glass part of the bulb.
1
U40BE0E0.book Page 27 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-28
6
EAU47660
Replacing the tail/brake light
bulb 1. Remove the tail/brake light outer
lens by removing the screws.
2. Remove the inner lens by pulling it
out.3. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Place the inner lens in the original
position, and then install the outer
lens by installing the screws.
NOTICE: Do not overtighten the
screws, otherwise the lens may
break.
[ECA10681]EAU47740
Replacing a front turn signal
light bulb 1. Remove cowling A. (See page
6-6.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
3. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
1. Outer lens
2. Screw
1. Inner lens
21
1
1. Tail/brake light bulb
1
1. Turn signal light bulb socket
1
U40BE0E0.book Page 28 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6 4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the socket (together with the
bulb) by turning it clockwise.
6. Install the cowling.
EAUS1610
Replacing a rear turn signal
light bulb 1. Remove the turn signal lens by re-
moving the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11191]
1. Turn signal light bulb
1
1. Screw
1
1. Turn signal light bulb
1
U40BE0E0.book Page 29 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
6 6. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
7. Install the rubber cap.
8. Connect the speedometer cable.
EAU25080
Rear wheel
EAU47710
To remove the rear wheel
WARNING
EWA10821
To avoid injury, securely support the
vehicle so there is no danger of itfalling over.
1. Place the motorcycle on the cen-
terstand.
2. Remove the drive chain case by
removing the screws.
3. Loosen the axle nut.4. Loosen the locknut and the drive
chain slack adjusting nut on both
ends of the swingarm.
5. Loosen the brake torque rod nut at
the brake shoe plate.
6. Disconnect the brake torque rod
from the brake shoe plate by re-
moving the cotter pin, the nut, the
washer and the bolt.1. Drive chain case
2. Screw
1
2
2
1. Locknut
2. Drive chain slack adjusting nut
3. Washer
4. Axle nut
12
3
4
U40BE0E0.book Page 33 Wednesday, January 7, 2009 10:05 AM

INDEXAAir filter element, cleaning..................... 6-10
Auxiliary light bulb, replacing ................ 6-30BBattery................................................... 6-24
Brake fluid, changing ............................ 6-18
Brake fluid level, checking .................... 6-17
Brake lever .............................................. 3-4
Brake lever, checking and lubricating ... 6-21
Brake pads and shoes, checking .......... 6-16
Brake pedal ............................................. 3-5
Brake pedal, checking and
lubricating ........................................... 6-22
Brake pedal free play, adjusting............ 6-15CCables, checking and lubricating .......... 6-21
Carburetor, adjusting ............................ 6-11
Care ........................................................ 7-1
Carrier ................................................... 3-10
Catalytic converter .................................. 3-7
Centerstand, checking and
lubricating ........................................... 6-22
Cowling and panel, removing and
installing................................................ 6-6DDimmer switch ........................................ 3-4
Drive chain, cleaning and lubricating .... 6-20
Drive chain slack ................................... 6-18EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-11
Engine oil ................................................ 6-8
Engine serial number .............................. 9-2
Engine, starting a warm .......................... 5-2
FFront fork, checking .............................. 6-23
Fuel......................................................... 3-6
Fuel consumption, tips for reducing........ 5-3
Fuel gauge.............................................. 3-3
Fuel tank cap .......................................... 3-5
Fuse, replacing ..................................... 6-26GGear position indicator lights .................. 3-2HHandlebar switches ................................ 3-3
Headlight bulb, replacing ...................... 6-27
Helmet holders ....................................... 3-9
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-4IIdentification numbers ............................ 9-1
Indicator lights ........................................ 3-2KKey identification number ....................... 9-1
Kickstarter............................................... 3-8LLicense plate light bulb, replacing ........ 6-30MMain switch/steering lock........................ 3-1
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Matte color, caution ................................ 7-1NNeutral indicator light .............................. 3-2PParking ................................................... 5-4
Part locations .......................................... 2-1
RRear brake light switch, adjusting ......... 6-16SSafety information ................................... 1-1
Seat ......................................................... 3-8
Shifting .................................................... 5-2
Shift pedal ............................................... 3-4
Shift pedal, checking ............................. 6-16
Spark plug, checking ............................... 6-7
Specifications .......................................... 8-1
Speedometer unit .................................... 3-3
Starter (choke) lever................................ 3-8
Starting and warming up a cold engine ... 5-1
Start switch.............................................. 3-4
Steering, checking................................. 6-23
Storage.................................................... 7-3
Storage compartment.............................. 3-9
Swingarm pivots, lubricating ................. 6-22TTail/brake light bulb, replacing .............. 6-28
Throttle cable free play, checking ......... 6-12
Throttle grip and cable, checking and
lubricating ........................................... 6-21
Tires ...................................................... 6-13
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-35
Troubleshooting chart ........................... 6-36
Turn signal indicator light ........................ 3-2
Turn signal light bulb (front),
replacing ............................................. 6-28
Turn signal light bulb (rear), replacing... 6-29
Turn signal switch ................................... 3-4VValve clearance..................................... 6-12
U40BE0E0.book Page 1 Wednesday, January 7, 2009 10:05 AM