2009 YAMAHA T105 clock

INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
EAU12941
Brake pedal The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.
EAU37471
Fuel tank cap To remove the fuel tank cap
1. Open the seat. (See page 3-8.)
2. Turn the fuel tank cap counter-
clockwise and pull it off.
To install the fuel tank cap
1. Insert the fuel tank cap into the
tank opening and turn it clockwise
until the“” marks on the cap
and tank are aligned.
2. Close the seat.
WARNING
EWA11091
Make sure that the fuel tank cap is
properly closed after filling fuel.Leaking fuel is a fire hazard.
1. Brake pedal
1
1. Fuel tank cap
2.“” mark
1
2
2
U40BE0E0.book Page 5 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
6
EAU47760
Replacing a headlight bulb If a headlight bulb burns out, replace it
as follows.NOTICE
ECA10650
Take care not to damage the follow-
ing parts:

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.


Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of awattage higher than specified.
1. Remove cowling A. (See page
6-6.)
2. Remove the headlight bulb cover.3. Remove the headlight bulb holder
(together with the bulb) by turning
it counterclockwise.
4. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.5. Place a new bulb into the holder,
push it in, and then turn it clock-
wise until it stops.
6. Install the bulb holder (together
with the bulb) by turning it clock-
wise.
7. Install the headlight bulb cover.
8. Install the cowling.
9. Have a Yamaha dealer adjust the
headlight beam if necessary.
1. Headlight bulb cover
1. Headlight bulb holder
2. Headlight bulb
1
1
2
1. Do not touch the glass part of the bulb.
1
U40BE0E0.book Page 27 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-28
6
EAU47660
Replacing the tail/brake light
bulb 1. Remove the tail/brake light outer
lens by removing the screws.
2. Remove the inner lens by pulling it
out.3. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Place the inner lens in the original
position, and then install the outer
lens by installing the screws.
NOTICE: Do not overtighten the
screws, otherwise the lens may
break.
[ECA10681]EAU47740
Replacing a front turn signal
light bulb 1. Remove cowling A. (See page
6-6.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
3. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
1. Outer lens
2. Screw
1. Inner lens
21
1
1. Tail/brake light bulb
1
1. Turn signal light bulb socket
1
U40BE0E0.book Page 28 Wednesday, January 7, 2009 10:05 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6 4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the socket (together with the
bulb) by turning it clockwise.
6. Install the cowling.
EAUS1610
Replacing a rear turn signal
light bulb 1. Remove the turn signal lens by re-
moving the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11191]
1. Turn signal light bulb
1
1. Screw
1
1. Turn signal light bulb
1
U40BE0E0.book Page 29 Wednesday, January 7, 2009 10:05 AM