2009 TOYOTA SIENNA lock

487
4-3. Do-it-yourself maintenance
4
Maintenance and care
Replacing light bulbs
■ Headlight (halogen bulbs)
Turn the bulb base counterclock-
wise.
Headlight (high beam)
Headlight (low beam)
Pull out the light bulb while
depressing the lock release.
■ Rear bulb locations
Back-up lights
Rear turn signal lights
Stop/tail and rear
side
marker
lights
License plate lights
Ta i l lights
STEP1
STEP2

488 4-3. Do-it-yourself maintenance
■Front side marker light
Turn the bulb base counterclock-
wise.
Remove the light bulb.
STEP1
STEP2

489
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
Parking and front turn signal lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.
STEP1
STEP2

490 4-3. Do-it-yourself maintenance
■Rear turn signal, stop/tail a nd rear side marker lights
Remove the securing bolts and
remove the unit.
To protect the cover, place a rag
between the flathead screwdriver
and cover as shown in the illus-
tration.
Turn the bulb bases counter-
clockwise.
Remove the light bulbs.
Rear turn signal light
Stop/tail and rear side marker
light
STEP1
STEP2
STEP3

491
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
Tail and back-up lights
Open the back door and remove
the strap.
Remove the back door trim
board.
Turn the bulb bases counter-
clockwise.
Remove the light bulbs.
Tail light
Back-up light
STEP1
STEP2
STEP3
STEP4

492 4-3. Do-it-yourself maintenance
■License plate lights
Open the back door and remove
the strap.
Remove the back door trim
board.
Turn the bulb bases counter-
clockwise.
Remove the light bulb.
STEP1
STEP2
STEP3
STEP4

494 4-3. Do-it-yourself maintenance
CAUTION
■Replacing light bulbs
●Turn off the headlights. Do not attempt to replace the bulb immediately
after turning off the headlights.
The bulbs become very hot and may cause burns.
● Do not touch the glass portion of the light bulb with bare hands. Hold the
bulb by the plastic or metal portion.
If the bulb is scratched or dropped it may blow out or crack.
● Fully install light bulbs and any parts used to secure them. Failing to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
● Do not attempt to take apart or repair the low beam headlight bulbs, con-
nectors, power supply circuits, or related components.
Doing so could result in electric shock and serious injury or death.
■ Discharge headlights
●Contact your Toyota dealer before replacing discharge headlights (includ-
ing light bulbs).
● Do not touch the high-intensity discharge headlight’s high voltage socket
when the headlights are turned on.
An extremely high voltage of 20000 V will be discharged and could result
in serious injury or death by electric shock.
■ To prevent damage or fire
Make sure bulbs are fully seated and locked.
NOTICE
■When installing the back door trim
To prevent damage, be careful not to pinch any of the wire harnesses or
connectors with the back door trim.

5
When trouble arises
501
5-1. Essential information
Fuel pump shut off system
Follow the procedure below to restart the engine after the system is
activated.
Turn the engine switch to the “ACC” or “LOCK” position.
Restart the engine.
NOTICE
■Before starting the engine
Inspect the ground under the vehicle.
If you find that fuel has leaked on to the ground, the fuel system has been
damaged and is in need of repair. Do not restart the engine.
To minimize the risk of fuel leakage when the engine stalls or an air-
bag inflates upon collision, the fu el pump shut off system stops sup-
plying fuel to the engine.
STEP1
STEP2