2009 SKODA YETI length

Heating and air conditioning system
104
Switching cooling on and offSwitching cooling on and off–Press the button
⇒page 103, fig. 110
. The warning light lights up in the button.
– When you again press the switch , the cooling system is switched off. The
warning light in the button goes out. Only
the function of the ventilation remains
active when no lower temperature than the outside temperature can be reached.
Setting temperatureYou can separate the interior temperature for the left and right side separately. – You can set the temperature for both sides
after switching on the ignition with the
control dial .
– If you wish to set the temperature for the right side, turn the control dial . The
warning light in the button lights up,
this indicates that differing tempera-
tures for the left and right side can be set.
If the warning light in the button lights up, the temperature for both sides cannot be set with the control dial . You can
reinitiate this functi
on by pressing the
button . The warning light in the button which indicates the possibility to set differing temperatures for the left and right side, goes out. You can set the interior temperature between +18°C and +26°C. The interior temper- ature is regulated automatically within this
range. If you chose a temperature lower
than +18°C, a blue symbol lights up at the
start of the numerical
scale. If you chose a
temperature higher than +26°C, a red symbol lights up at the end of the numerical scale. In both limit positions the Climatroni
c operates at maximum cooling or heating
capacity, respectively. The temperatur
e is not controlled in this case.
Lengthy and uneven distri
bution of the air flow out of the vents (in particular at the leg
area) and large differences in temperature, for example when getting out of the vehicle, can result in chills in sensitive persons.
Recirculated air mode In recirculated air mode air is sucked out of the interior of the vehicle and then fed back into the interior. When the automatic air distribution control is switched on, an air quality sensor measures the concentration of pollutants in the drawn-in air.Recirculated air mode prevents polluted air outside the vehicle from getting into the vehicle, for example when driving through a tunn
el or when standing in a traffic jam. If
a considerable increase in concentration of
pollutants is recognized by the air quality
sensor, when the automatic air distribution co
ntrol is switched on, the air distribution
control will temporarily be switched off. If
the concentration of po
llutants decreases to
the normal level, the air distribution control
is automatically switched off so that fresh
air can be guided into
the vehicle interior.
Switching recirculated air mode on– Press the button repeatedly
until the warning light on the left side of the
button lights up.
Switch on automatic air distribution control– Press the button repeatedly
until the warning light on the right side of the
button lights up.
Switch off automatic air distribution control temporarily– If the air quality sensor does not switch on
the air distribution control automatically
when there is a nauseating smell, you can
switch it on yourself by pressing the
button *. The warning light lights up
in the button on the left side.
Switching recirculated air mode off– Press the button or press the button repetitively, until the warning
lights in the button go out.
WARNING
You should not leave recirculated air mode on over a longer period of time, as “stale” air may result in fatigue in the driver and occupants, divert your atten-
AC
AC
A7
A14
DUALDUALA7
DUAL


AUTO

sgg.6.book Page 104 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
112
•
The brake booster only operates when
the engine is running. Greater phys-
ical effort for braking is required when en
gine is switched off. Because if you do
not stop as normal, this can cause an accident and severe injuries.
Caution
you should not switch the engine off right
away at the end of your journey after the
engine has been operated for a lengthy period
at high loads but should be allowed it
to run at idling speed for
about 2 minutes. This prevents any accumulation of heat
when the engine is switched off.
Note
•
The radiator fan may continue running fo
r a further 10 minutes or so after the
engine and the ignition have been switched
off. The coolant fan may, however, also
switch on again after some time if the co
olant temperature rises because of an accu-
mulation of heat in the engine or if the engine is warm and the engine compartment is additionally heated
by strong sunlight.
•
This is why particular care is required
when carrying out any work in the engine
compartment
⇒page 204, “Working in the engine compartment”.
Shifting (manual gearbox)
Shift into reverse only when the vehicle is
stationary. Depress the clutch pedal and hold
it fully depressed. Wait a mo
ment before engaging reverse gear in order to avoid any
shift noises. The reversing lights will come on once reverse gear is engaged, provided the ignition is on.
WARNING
Never engage the reverse gear when driving - risk of accident!
Note
•
One should not lay the hand on the shift lever while driving the vehicle. The pres-
sure of the hand will be transferred to the gearshift forks in the gearbox. This can, over a period of time, lead to earl
y wear of the gearshift forks.
•
Depress the clutch pedal fully when changi
ng gears, in order to avoid unnecessary
wear and damage.HandbrakeApplying the handbrake– Pull the handbrake lever up fully.
WARNING (continued)
Fig. 115 The shift pattern: 5-speed or 6- speed manual gearbox
Fig. 116 Centre console: Handbrake
sgg.6.book Page 112 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
115
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
set so that the play function volume decr
eases when activating the parking aid, see
Owner's Manual radio* or na
vigation system*. This impr
oves the audibility of the
parking aid. Activating The parking aid is activated when the
reverse gear
is engaged and the ignition is
turned on or by pressing the button
⇒page 114, fig. 118
- the symbol lights up in
the button. The activation is confirme
d by a brief acknowledgement signal.
Deactivating The parking aid is deactivated after pressing the button°
⇒page 114, fig. 118
or at
a speed of more than 10 km/h - the symbol
 in the button is no longer illuminated.
WARNING
•
The parking aid is not a substitute for the driver paying proper attention and
it is always the driver's responsibility to
take care when reversing the vehicle or
carrying out similar manoeuvres.•
You should therefore satisfy yourself, befo
re reversing, that there is no small
obstacle, such as a rock, thin post, trailer drawbar etc., in front or behind your vehicle. Such an obstacle might not be
within the range dete
cted by the sensors.
•
Under certain circumstances, surfaces
of certain objects and types of
clothing cannot reflect the signal of th
e parking aid. Thus, these objects or
people who wear such clothing are not re
cognised by the sensors of the parking
aid.
Note
•
Only the front parking aid operates if yo
u are towing a trailer (applies only to
models which feature a factory-fitted towing device*).•
If a warning signal sounds for about 3 seco
nds after activating the system and there
is no obstacle close to your
vehicle, this indicates a system fault. The fault is confirmed
additionally when the symbol flashes in the button
⇒page 114, fig. 118
. Have the
fault rectified by a specialist workshop.•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.
•
If the parking aid is activated and the sele
ctor lever of the automatic gearbox is in
the position , warning signal indicates inte
rruption (vehicle can no longer move).
Park Assist*Description and important informationThe park assist assists you when parking in a suitable parallel parking space between two vehicles or
behind a vehicle.
The park assist automatically searches for
suitable parking spaces
after switching on
the ignition and when driving up to 30 km/h. During the parking procedure the park assist only takes over the steering movements, the pedals continue to be operated by the driver. Function of the system is based on:•
Length and depth measurement of the parking spaces when driving
•
Evaluation of the size of the parking space
•
Definition of the correct position of the vehicle for parking
•
Calculating the line on which the vehicle drives backwards into the parking space
•
Actuation of the steering force assistance, automatic spinning of the wheels of the
front axle when parking.
WARNING
The park assist does not take away the responsability from the driver when parking.•
Pay particular attention to small children and animals as they would not be
recognised by the sensors of the parking aid.•
Under certain circumstances, surfaces of certain objects and types of
clothing cannot reflect the signal of the park assist or the parking aid. Thus, these objects or people who wear such clothing are not recognised by the sensors of the parking aid.



AP
sgg.6.book Page 115 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
175
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The technical requirements for low fuel usage and economic efficiency of the vehicle have already been built into the vehicle at
the works. Special atte
ntion has been given
to minimising nega
tive effects on the environment. It
is necessary to take note of the
guidelines given in this chapter in order to
make best use of these characteristics and
to maintain their effectiveness. The optimal engine speed should be obtained
when accelerating, in order to avoid a
high fuel consumption and
resonance of the vehicle.
Looking ahead when driving A vehicle's highest fuel consumption occurs it accelerates.Avoid accelerating and braking unnecessarily.
If you drive with forsight you will not
need to brake so often and will also then
not have to accelerate so much. Let your
vehicle coast to a stop, for example, if this is possible, when you see that the next set of traffic lights is at red.Shifting gears and saving energy Shifting up early saves on fuel.Fig. 159 Fuel consumption in litres/100 km. and speed in km/h.Manual gearbox– Drive no more than about one length of your vehicle in first gear. – Shift up into the next higher gear at approx. 2 000 to 2 500 revs.
Automatic gearbox– Depress the accelerator pedal
slowly
. Do not depress it beyond the kickdown
position, however.
An effective way of achieving good fuel economy is to shift up
early
. You will consume
more fuel if you drive at unnecessaril
y high revolutions in any given gear.
The
⇒fig. 159
shows the ratio of fuel consumption
to the speed of your vehicle in the
relevant gear. Fuel consumption in 1st gear
is the highest. The consumption is the
lowest in the highest gear. You will achieve good fuel economy by shif
ting up early and shifting down late.
Shift recommendation
for changing gears*
An information for the engaged gear
⇒fig. 159
is shown in the display of the
instrument cluster. In order to minimise the fuel consumptio
n, a recommendation for shifting into
another gear is indicated in the display. If the control unit recognises
that it is appropriate to change the gear, an arrow is
shown in the display. The arrow points up or down, depending on whether it is recom- mended to shift into a higher or lower gear. At the same time, the recommended gear is indicated instead of the currently engaged gear .
Note
Also use the information supplied by the multi-functional indicator*
⇒page 20.
AA
AB
AA
sgg.6.book Page 175 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
176
Avoiding full throttle Driving more slowly means saving fuel.Sensitive use of the accelerator will not only
significantly reduce fuel consumption but
also positively influence environmenta
l pollution and wear of your vehicle.
You should avoid exploiting the top speed
of your vehicle wherever possible. Fuel
consumption, pollutant emissions and vehicle noises increase disproportionally at high speeds. The
⇒fig. 160
shows the ratio between the fuel
consumption and the speed of your
vehicle. You will cut your fuel consumption by
half if you only make use three-quarters
of the possible top speed of your vehicle.Reducing idling Idling also costs fuel.It is worthwhile switching off the engine in
a traffic jam or when waiting at a level
crossing or at traffic lights with a lengthy red phase. Even after just 30 - 40 seconds you will have saved more fuel th
an that is needed when you start the engine up again.
If an engine is only idling it takes much
longer for it to reach its normal operating
temperature. Wear-and-tear and pollutant emis
sions, though, are particularly high in
the warming-up phase. This is why you should drive off right after starting the engine. Do avoid high engine revolu
tions at this time, however.
Regular servicing A poorly tuned engine consumes an unnecessarily high amount of fuel.Having your vehicle serviced regularly at a specialist garge enables you to satisfy
one

of the requirements for economical motoring
even before you set off on your journey.
Keeping your vehicle properly serviced not on
ly has a positive effect on the safety of
your vehicle and maintaining its value, but also saves on
fuel
.
A poorly tuned engine can result in a fuel consumption which is 10% higher than normal. The foreseen maintenance work should be undertaken exactly according to the Service schedule by a specialist garage. Also check the
oil level
after refueling.
Oil consumption
is dependent to a consider-
able extent on the load and speed of the en
gine. Oil consumption could be as high as
0.5 litres/1 000 km depending on your style of driving. It is quite normal that a ne
w engine has a higher oil cons
umption at first, and reaches
its lowest level only after a certain running
in time. It is therefore not possible to
correctly assess the oil consumption of a ne
w vehicle until after you have driven about
5 000 km.
For the sake of the environment
•
You can achieve additional
improvements in your fuel economy by using high-
lubricity oils.•
Check the ground below your vehicle at regular intervals to detect any leakages in
good time. Please have your vehicle inspec
ted by a specialist garge if you find any
stains caused by oil or other fluids on the floor.
Fig. 160 Fuel consumption in litres/100 km. and speed in km/h.
sgg.6.book Page 176 Thursday, September 24, 2009 2:32 PM

Towing a trailer
191
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Headlights Before starting off with a hitched trailer, also check the setting of the headlights. Alter the setting as necessary with the ai
d of the headlight beam adjuster
⇒page 58.
Detachable ball head The ball rod is detachable on vehicles which
feature a factory-fitted
towing device. It is
stowed together with separate fitting instru
ctions in the spare wheel well in the luggage
compartment of the vehicle. Further information on the towing device
⇒page 192.
Note
•
We recommend that you also have your
vehicle inspected between service inter-
vals if you tow a trailer frequently.•
The handbrake on the towing vehicle must be put on when coupling and decou-
pling the trailer.Driving Tips Particular caution is required when towing a trailer.– Do not, as far as possible, drive with
your vehicle unladen and the trailer laden.
– Do not make full use of the legal maximum speeds. This applies in particular to
downhill sections.
– Apply the brakes in good time. – Keep a check on the coolant temperature gauge if the outside temperature is high. Distribution of weight The distribution of the weight
is very poor if your vehicle
is unladen and the trailer is
laden. Maintain a particularly low speed if you cannot avoid driving with this combina-tion. Driving speed Do not drive faster than 80 km/hour for safety reasons. This also applies for countries in which higher speeds are allowed.
The fact that the driving stability of the vehicle + trailer combination reduces with increasing speed means that the legally allowed speed should not be used when there are unfavourable road, weather or wind cond
itions, particularly near accident black
spots. You must always reduce your speed immediat
ely as soon as you detect even just the
slightest swaying
of the trailer. On no account attempt to stop the trailer from
“swaying” by accelerating. Apply the brakes in good time! If
the trailer is fitted with a
trailer brake
, apply the
brakes gently at first and then brake firmly. This will avoid brake jolts resulting from the trailer wheels locking. Shift down gears in good time before negotiating a downhill section to allow the engine to also act as a brake. Engine overheating Please keep a check on the coolant temperature gauge if you have to negotiate a lengthy slope in a low gear at a high engi
ne speed when the outside temperature is
very high
⇒page 17, “Coolant temperature gauge”.
If the needle of the coolant temperature gauge moves into the right-hand area or even the red area of the scale, reduce your speed immediately. Stop and switch off the engine if the warning light
 in the instrument cluster begins flashing. Wait a few
minutes and check the level of coolant in the coolant expansion bottle
⇒page 207,
“Inspecting the coolant level”. Please refer to the following guidelines
⇒page 34, “Coolant temperature/ Coolant
quantity
”.
The coolant temperature can be reduced by switching on the heating.Any increase in the cooling effect of the coolant fan through shifting down a gear and increasing the engine speed is not possible
since the fan speed is independent of the
engine speed. One should also not drop a gear
for this reason when towing a trailer as
long as the engine can manage th
e slope without any drop in speed.
sgg.6.book Page 191 Thursday, September 24, 2009 2:32 PM

Taking care of your vehicle and cleaning the vehicle
198
Upholstery cloth and cloth trim on the d
oors, luggage compartment cover, headliner
etc. are best treated with special cleaning products, using if necessary a
dry foam
and
a soft sponge or brush. We recommend using a cleaning product from Škoda genuine accessories offered by your Škoda dealer.
Caution
Solvent-free cleaners attack th
e material and can damage it.
Fabric covers of elec
trically heated seats
Do
not clean
the seat covers moist as this may re
sult in damage to the seat heating
system. Clean such covers using specia
l agents, for example dry foam.
Natural leather Natural leather requires quite particular care and attention.Leather should be treated from time to time according the following guidelines depending on how much it is used.Normal cleaning– Clean soiled areas of the leather with
slightly moistened co
tton or woollen cloth.
Severe soiling– Clean severely soiled areas with a cloth
dipped in a mild soap
y solution (2 spoon-
fuls of natural soap to 1 litre of water).
– Ensure that the leather is not soaked through at any point and that no water gets
into the stitching of the seams.
– Dry off the leather with a soft, dry cloth.
Removing stains– Remove fresh stains which are
water-based
(e.g. coffee, tea, juices, blood etc.)
with an absorbent cloth or household pape
r or use the cleaner from the care set
for a stain which has already dried in.
– Remove fresh stains on a
fat base
(e.g. butter, mayonnaise, chocolate etc.) with an
absorbent cloth or household
cleaning paper or with the
cleaner from the care set
if the stain has not yet pe
netrated into the surface.
– Use a grease dissolver for
grease stains which have dried in
.
–Eliminate
special stains
(e.g. ball-point pens, felt pe
n, nail varnish, dispersion
paint, shoe cream etc.) with a special stain remover suitable for leather.
Leather care– Treat the leather every six months with th
e leather care product available from an
authorised Škoda Service Partner.
– Apply only a small amount of the care product.– Dry the leather off with a soft cloth. It is best to consult an authorised Škod
a Service Partner if you have any questions
regarding cleaning and care of the
leather interior in your vehicle.
Caution
•
You must on no account treat the leather wi
th solvents (e.g. gasoline, turpentine),
floor wax, shoe cream or such like.•
Avoid leaving your vehicle for lengthy period
s in bright sunlight in order to avoid
bleaching the leather. If you
leave your vehicle parked in the open for lengthy periods,
protect the leather from the direct ra
ys of the sun by covering it over.
•
Sharp-edged objects on items of clothing su
ch as zip fasteners, rivets, sharp-edged
belts may leave permanent scratches or signs of rubbing on the surface.
Note
•
Use a care cream with ligh
t blocker and impregnation
effect regularly and each
time after cleaning the leathe
r. The cream nourishes the leather, allows it to breathe
and keeps it supple and also provides mois
ture. It also creates surface protection.
sgg.6.book Page 198 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
206
Oil level within range –You
must
top up the oil
⇒page 206. It is sufficient, once this is done, to keep the
oil level within range .
It is normal for the engine to consume oil.
The oil consumption may be as much as 0.5
l/1 000 km depending on your style of driving and the conditions under which you operate your vehicle. The oil
consumption may be slightly hi
gher than this during the
first 5 000 kilometres. One should therefore check the oil level at regular intervals, preferably every time after the fuel tank is filled or after driving for long stretches. We recommend maintaining the oil level within the range -
but not above this
, if
the engine has been operating at high load
s, for example during a lengthy motorway
trip during the summer months, towing a tr
ailer or negotiating
a high mountain pass.
The warning light in the instrument cluster* will indicate
⇒page 33, “Engine oil pres-
sure

” whether the oil level is too low. In this case, check the oil level as soon as
possible. Top up with an appropriate quantity of oil.
Caution
•
The oil level must on no account extend
beyond the range . Danger of damaging
the catalytic converter.•
Do not continue your journey
if for some reason it is not possible under the
conditions prevailing to top up with oil.
Switch the engine off
and obtain professional
assistance from a specialist garage, otherwise it could lead to severe engine damage.
Note
Engine oil specifications
⇒page 243, “Technical Data”.
Replenishing engine oil– Inspecting the engine oil level
⇒page 205.
– Unscrew the cap of the engine oil filler opening. – Pour in a suitable grade of oil in portions of 0.5 litres
⇒page 246, “Engine oil spec-
ifications”.
– Inspect the oil level
⇒page 205.
– Carefully screw on the cap of the filler opening and push the dipstick in fully.
WARNING
•
Avoid dripping oil onto hot parts of the engine when topping up will oil - a
risk of fire!•
Read and observe the warning notes
⇒page 204, “Working in the engine
compartment” before working in the engine compartment.
For the sake of the environment
The oil level must on no acco
unt extend beyond the range
⇒page 205. Oil will
otherwise be drawn in through the crankc
ase ventilation and may pass through the
exhaust system to atmosphere. The oil ma
y combust in the cata
lytic converter and
damage it.Changing engine oilThe engine oil must be changed at the intervals stated in the Service schedule or according to the service interval indicator
⇒page 18, “Service Interval Display”.
WARNING
•
Only carry out the engine oil change, if you have the required professional
knowledge!•
Read and observe the warning notes
⇒page 204, “Working in the engine
compartment” before working in the engine compartment.•
First of all, let the engine cool down, we
ar an eye protection and gloves - risk
of caustic burns due to hot oil.
Caution
You must not pour any
additives into the engine oil - risk of engine damage! Damage,
which results from such product, are excluded from the warranty.
ACAB
AAAA
AA
sgg.6.book Page 206 Thursday, September 24, 2009 2:32 PM