2009 SKODA SUPERB lock

Breakdown assistance
251
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Start engineIt is important to connect the jump
-start cables in the correct order.
Connecting positive terminals – Attach one end to the positive terminal
⇒
fig. 222
of the
discharged battery .
– Attach the other end to the positive terminal of the battery
supplying the power .
Connecting negative term
inal and engine block
– Attach one end to the negative
terminal of the battery supplying
the power .
– Attach the other end to a solid metal part which is connected
firmly to the engine block, or
to the engine block itself.
Starting engine – Start the engine of the vehicle providing current and run the engine at
idling speed.
– Now start the engine of the vehicle with the discharged battery.
– Interrupt the attempt at starting an engine after 10 seconds if it does
not start right away and wait for about 30 seconds before repeating the attempt.
– Disconnect the cables on the engine in exactly the
reverse order
they
were connected up.
WARNING
•
The non-insulated parts of the terminal clamps must never make contact
with each other. Furthermore, the cable connected to the positive terminal of the battery must not come into contact with electrically conducting parts of the vehicle - risk of a short circuit!•
Do not affix the jump starting cables to the negative terminal of the
discharged battery. There is the risk
of detonating gas seeping out the
battery being ignited by the strong
spark which results from the engine
being started.•
Run the jump-start cables so that th
ey cannot be caught
by any rotating
parts in the engine compartment.•
Do not bend over the batteries - risk of caustic burns!
•
The vent screws of the battery cells must be tightened firmly.
•
Keep any sources of ignition (naked
flame, smouldering cigarettes etc.)
away from the battery - risk of an explosion!•
Never jump-start the batteries which have a too low electrolyte level -
risk of explosion and caustic burns!
Fig. 222 Jump-starting using the battery from another vehicle: A - flat vehicle battery, B - battery providing current
A1AAA2AB
A3
AB
A4
s2dk.1.book Page 251 Wednesday, April 8, 2009 12:23 PM

Breakdown assistance
252
Jump-starting on vehicles with jump-starting pointFor vehicles with the 3.6 ltr./191 kW FS
I engines, the positive terminal of
the battery supplying the power can only be connected to the jump-starting point in the engine compartment of the vehicle which must be started by means of a jump-starting cable
⇒
fig. 223
!
– Open the protective cap of the ju
mp-starting point in direction of
arrow.
– Connect the positive terminal of
the battery supplying the power with
the jump-starting point.
– Attach the negative terminal of the battery supplying the power to a
solid metal part which is connected fi
rmly to the engine block or to the
engine block itself.
–Start the engine
⇒
page 251.
– After the engine start, close the
protective cap of the jump-starting
point.
Tow-starting and towing vehicleGeneralPlease pay attention to the following in
structions if you are going to use a
tow rope: Driver of the towing vehicle – Do not drive off until the tow rope is taught. – Release the clutch particularly gent
ly when starting off or depress the
accelerator particularly gently if yo
ur vehicle is fitted with an auto-
matic gearbox.
Driver of the towed vehicle – Switch the ignition on so that th
e steering wheel is not blocked and
you can also operate the turn signal
lights, the headlight flasher, the
windscreen wipers and windscreen washer system.
– Take the vehicle out of gear or move the selector lever into position
N
if your vehicle is fitted
with an automatic gearbox.
– Note that the brake servo unit and po
wer steering only operate if the
engine is running. You will require
significantly greater physical force
to depress the brake pedal and to steer the vehicle if the engine is not running.
– Ensure that the tow rope is always kept taught.Tow rope or tow bar A tow
bar
is safest way of towing a vehicle and also minimizes any shocks. You can
use a tow
rope
only if a suitable tow bar is not available.
The tow rope must be elastic to protect
the vehicle. Thus one should only use
plastic fibre rope or a rope made
out of a similarly elastic material.
Fig. 223 Detail of the engine compartment: Jump-starting point
s2dk.1.book Page 252 Wednesday, April 8, 2009 12:23 PM

Breakdown assistance
253
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Only attach the tow rope to the
towing eyes
provided for this purpose
⇒page 253
and
⇒page 254.
Driving style Towing another vehicle requires a certain
amount of practice. Both drivers should
be familiar with the particular points
about towing a vehicle. Unskilled drivers
should not attempt to tow in another vehicle or to be towed in. One should be constantly vigilant not to
allow impermissibly high towing forces or
jerky loadings. There is always a risk of excessive stresses and damage resulting at the points to which you attach the tow rope or tow bar when you attempt to tow a vehicle which is not standing on a paved road.
Caution
If the gearbox of your vehicle no longer
contains any oil because of a defect, your
vehicle must only be towed in with the driv
en wheels raised clear of the ground, or
on a special vehicle transporter or trailer.
Note
•
Please comply with any legal requirements particularly regarding the switched
on signal systems, when towing in
or tow-starting
another vehicle.
•
The tow rope must not be twisted as it may in certain circumstances result in the
front towing eye being unscr
ewed out of your vehicle.
Front towing eye The towing eye is stored in th
e box for the vehicle tool kit.
– Take the cover out of the front bumper
⇒
fig. 224
.
– Screw in the towing eye anticlockwise down to the stop
⇒
fig. 225
and
tighten up using the wheel wrench (push the wheel wrench through eye).
– Put the cover in place after screwing out the towing eye again and
press into place. The cover must engage firmly.
Fig. 224 Front bumper: Removing the coverFig. 225 Front bumper: Installing the towing eye
s2dk.1.book Page 253 Wednesday, April 8, 2009 12:23 PM

Breakdown assistance
254
Rear towing eye– Press onto the bottom part of the cover in the rear bumper
⇒
fig. 226

and take it out.
– Screw in the towing eye anti
clockwise down to the stop
⇒
fig. 227
and
tighten up using the wheel wrench (push the wheel wrench through eye).
– Put the cover in place after screwing out the towing eye again and
press into place. The co
ver must engage firmly.
Tow-starting a vehicleIf the engine does not start, we generally do
not
recommend
to tow-start
your vehicle. One should attempt to start the engine using jump start cables
⇒
page 250 or call on the services of the SERVICE mobile.
If your vehicle has to be towed – Engage 2nd or 3rd gear wi
th the vehicle stationary.
– Depress the clutch pedal fully and keep it depressed. – Switch on the ignition.– Wait until both vehicles are movi
ng then release the clutch pedal
slowly.
– Depress the clutch pedal fully when the engine fires and take the
vehicle out of gear.
For technical reasons it is not possib
le to tow-start a car fitted with an
automatic
gearbox
.WARNING
There is high risk of having an accident when tow-starting a vehicle, when for example the towed vehicle runs into the towing vehicle.
Caution
Vehicles which are fitted with a catalytic
converter should not be tow-started over
a d i s t a n c e o f m o re t h a n 5 0 m e t re s . U n b u r n
t fuel may get into the catalytic converter
and damage it.Towing in a vehicle fitted with a manual gearboxPlease refer to the notes
⇒page 252.
Fig. 226 Rear bumper: Removing coverFig. 227 Rear bumper: Installing the towing eye
s2dk.1.book Page 254 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
257
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Fuse cover in engine compartment The fuse box in the engine comp
artment exists in two different
versions. You can determine which version your vehicle is fitted with after removing the fuse cover at the location of the fuses.On some vehicles, the battery cover
must be removed before removing
the fuse cover
⇒
page 229.
Removing fuse cover – Move the circlips
⇒
fig. 229
as far as the stop, the symbol

appears behind the circlip and remove the cover.
Installing fuse cover – Position the fuse cover on the fuse box and push the circlips as far
as the stop - the symbol
 is visible behind the circlip.
Caution
•
When unlocking and locking the fuse cover,
it must be pressed on the sides to
the box, otherwise damage can
occur to the locking mechanism.
•
Carefully position the fuse cover in th
e engine compartment. If the cover was
not correctly positioned, water can get into
the fuses and this results in a damage
to the vehicle!
Fuse assignment in engine compartment - version 1Certain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
Fig. 229 Fuse cover in engine compartment
AA
AA
No.
Power consumer
Amperes
F1
Front right main headlight, right rear light unit
30
F2
Valves for ABS
20
F3
Not assigned
F4
Not assigned
F5
Horn
15
F6
Not assigned
F7
Not assigned
F8
Not assigned
F9
Valves
10
F10
Not assigned
F11
Lambda probe
10
Fig. 230 Schematic repre-sentation of fuse box in engine compartment - version 1
s2dk.1.book Page 257 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
260
Fuse assignment in the dash panelCertain electrical components are only st
andard on certain vehicle model versions
or only suppliable as optional
equipment for certain models.
No.
Power consumer
Amperes
1
Diagnostic socket, engine control unit, fuel pump relay, fuel pump control unit
7,5
2
Control unit for ABS, ESP, switch for tyre air pressure control, brake sensor
5
3
Switch and control unit for airbag
5
4
WIV, parking light, dimming mirrors, pressure sensor, telephone preinstallation
5
5
Control unit for headlamp beam adjustment and head- light swivel, control unit for parking aid, control unit for park assist
5
6
Instrument cluster, control
unit for electromechanical
power steering, Haldex, selector lever lock, power sup- ply for data bus
5
Fig. 232 Schematic repre- sentation of the fuse carrier in the dash panel
7
Valve heating, air mass meter
10
8
Control unit for trailer detection
5
9
Relay for auxiliary heating
5
10
Adaptive left main headlight
10
11
Adaptive right main headlight
10
12
Central locking of the front doors
10
13
Diagnostic socket, light switch, rain sensor, clock
7,5
14
Central locking system and bonnet lid
15
15
Central control unit - interior lights
7,5
16
Air conditioning system
7,5
17
Central locking system of the rear doors
10
18
Not assigned
19
Not assigned
20
Not assigned
21
Not assigned
22
Air blower for Climatronic
40
23
Front power window
30
24
Selector lever lock
5
25
Rear wind
ow heater
relay for auxiliary heating and ventilation
2530
26
Power socket in the luggage compartment
25
27
Fuel pump relay, Fuel pump relay, control unit for fuel pump, injection valves
1520
28
Not assigned
29
Preparation for the aftermarket radio
5
No.
Power consumer
Amperes
s2dk.1.book Page 260 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
264
– Replace the lamp, insert the connector with the new lamp and turn to
the right up to the stop.
– Insert the protective cap.
Note
We recommend that you have the headli
ght setting checked by a Skoda Service
Partner after replacing the light bulb.Fog lights– Switch the ignition and all lights off.
– Grasp the grille at the point marked with the arrow and take it out
⇒
fig. 236
.
– Guide your hand into the opening
in which the grille was located and
press the spring bolt
⇒
fig. 237
.
– Take out the fog light.– Turn the connector with the light bulb
up to the stop towards the left
and remove.
– Replace the lamp, insert the connector with the new lamp and turn to
the right up to the stop.
– For the installation, first of all insert the fog light with the interlock to
the side far away from the marking of the vehicle.
– Press into place the headlight onto the side facing the marking. – First of all put the grille with the latch in place on the side opposite the
marking.
– Press into place the protective grille onto the side facing the
marking.
Rear light unit
Fig. 236 Front bumper: Protective grilleFig. 237 Removing the front fog light
Fig. 238 Remove the outer part of the rear light unit
s2dk.1.book Page 264 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
265
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Remove and install the outer part of the rear light unit – Switch the ignition and all lights off. – Open the boot lid/luggage compartment door. – Take out the plug
⇒
page 264, fig. 238
and unscrew the rear light unit
using a torx wrench
19).
– Carefully take out the light. Do not pull the grommet with the cables
out of the body.
– To re-insert the rear light unit, firs
t of all guide it with the support
⇒
fig. 240
towards the front onto a bolt on the bodywork.
– Carefully press the rear light unit into the bodywork.– Screw the rear light unit tight and press in the plugs
⇒
page 264,
fig. 238
.
Remove and install the inner part of the rear light unit – Switch the ignition and all lights off. – Open the boot lid/luggage compartment door.
– Take off the cover of the rear light unit on the inner side of the bonnet
lid
⇒
fig. 239
.
– Press the spring bolt
⇒
fig. 239
and take the lamp holder out of the
housing of the rear light unit.
– To re-insert the lamp holder, guide it into the housing of the rear light
unit.
–Press onto the spring bolt
until it is heard to lock.
– Guide the cover of the rear light uni
t into the inner side of the bonnet
lid. Caution
When removing and installing the rear
light unit make sure not to damage the
paintwork of the vehicle and the rear light unit.Changing light bulbs in the rear light unit
19)The torx wrench is located in a ve
hicle toolkit box on the spare wheel.
Fig. 239 Remove the inner part of the rear light unit
AA
Fig. 240 Outer part of the rear light unit: Lamps
s2dk.1.book Page 265 Wednesday, April 8, 2009 12:23 PM