2009 SKODA ROOMSTER change time

Radio4
If you have switched off the radio by withdrawing the ignition key, the radio switches on again once the ignition is on.
Audio settings
Setting the bass
– Press the button , BASS appears in the display.
– Set the desired value by turning the button .
Setting treble
– Press the button , TRE appears in the display.
– Set the desired value by turning the button .
By pressing again the button or 5 seconds after the setting, the set values are stored and the radio returns to the normal mode.
Adjusting volume ratio
Balance
– By pressing the button repetitively, BAL appears in the display.
– You can set with the button the desired value of the volume ratio
between the left and right side.
Fa d er
– Press the button once again, FA D appears in the display.
– You can set with the button the desired value of the volume ratio
between the front and the rear.
By pressing again the button or 5 seconds after the setting, the set values are stored and the radio returns to the normal mode.
Setting the special functions
– Press the button for some considerable time, in order to activate
the menu Setup.
– Select the individual functions of the menu by pressing the button
briefly.
– Confirm the changed setting by turning the button .
– By pressing the button for some considerable time or 30 seconds
after the setting, the set values are automatically stored and the unit
returns to the normal mode.
GALA
Your radio increases automatically its volume with the increasing vehicle speed. A higher setting value results in a stronger volume increase.
ON VOL
Your radio stores the last volume set before switching off. If the value is higher, the volume is reduced to the value of the parameter ON VOL after switching on the radio again.
PHONE
If your vehicle is equipped with a handsfree system, you can switch on or off the monophone play function of the mobile phone calls via the loudspeakers of the vehicle.
AUX
Switching on or off the function s of the external audio source.
You can set the desired value in the range of LEV1 to LEV3. If you set the value OFF, the tone is not replayed from the external audio source.
BEEP
Switching on or off the tone signal when storing the radio stations.

A2

A2


A2

A2

A2
A2
A2
A2
s2e0.5.book Page 4 Wednesday, May 2, 2007 9:14 AM

Radio5
CD
Play function of the CD tack (tracks) in continuous or random order. If you select PLAY , the tracks are replayed in normal order. If you select SCHFFL (Schuffle), the tracks are replayed in random order.
LO U D
In case of low volume level, the function reinforces the range of bass and treble frequencies.
Note
Each setting change is stored by changing to another menu point.
Radio mode
Waveband switch-over
Your radio is fitted with the wavebands FM and AM, in order to change, press the button for a considerable time.
In the ranges FM1/AM1 and FM2/AM2 there are each 6 memory spaces available, in order to change, press the button briefly.
The process of searching for and storing the radio stations
Manual search
– Search the frequency of the desire d radio station by pressing the
button .
Automatic station finding SEEK
– The radio searches for the next radio station in the selected waveband
by pressing the button or .
Function SCAN
– The radio station of the current waveband is briefly played (10
seconds) by pressing the button briefly.
– This function is ended by pressing the button once again and the
current station is replayed.
Store station
– After selecting the radio station, hold the station key , on which it
should be stored until it briefly switches to mute and a brief signal
sounds.
Automatic station finding with storing the radio stations
– Press the button . An automatic station finding is started during
which the 6 stations with the strongest signal in the memory level FM2
and/or AM2 are stored. STORE is displayed on the display. This applies
only to the wavebands FM2 and AM2.
When storing the radio stations on the station keys is finished, you can call up the desired radio station by pressing a station key .
Note
The stored radio stations are updated and stored once again by repetitively pressing the button .
Radio text
Certain radio stations transmit additi onal text information - called radio
text.
Note
•The text information must not be available to all radio stations.
AM/FM
AM/FM
A2

A2
A2
A3
AS
A3A3
AS
s2e0.5.book Page 5 Wednesday, May 2, 2007 9:14 AM

Radio6
•Depending upon the quality of the received signal, the radio needs a specific time, in order to correctly read all the illustrated characters.
Tra f f i c re p o r t s
Activating and deactivating the traffic information
Press the button , TP appears in the display. If a set radio station does not transmit a traffic report, the radio searches for a station which transmits the traffic report. TP SEEK is displayed on the display.
If no radio station which transmits the traffic reports is found, NO TP is shown on the display.
An incoming traffic report au tomatically interrupts the CD play function or listening to a radio station, which at that moment is not transmitting a traffic report. INFO and the name of the current radio station is displayed on the display. At the end of the traffic report, the radio automatically returns to the original play function.
If you wish to deactivate the traffic in formation, press once again the button , TP goes out on the display.
External CD changer
Mode of the external CD changer
Your radio can be equipped with an original CD changer which can be
installed in your vehicle.
Selecting CD mode
– Start the play function of the ex ternal CD changer by pressing the
button .
– Select a CD with a station key .
Select track
– During the CD play function turn th e button to the left or to the
right, in order to select the previous or the next track.
– Press the button or for fast replay of the track (reverse or
forward). The play function is co ntinued after releasing the button.
Function SCAN
– Press the button , in order to scroll through the CD. The first 10
seconds of each title are played.
– In order to return to the normal mode, press once again the button
.
End the play function of the CD
– In order to end the play function of the CD and to activate the radio,
press the button . The CD remains in the unit.
Information on how to use a CD
CD to jump
Uneven road surfaces and strong vi brations may cause the CD to jump.
Formation of condensation
When it is cold and after rain showers, moisture can deposit in the CD drive (condensation). This can effect the CD jump or impair the play function. In such cases wait until the moisture has dissipated.
Notes for the care of the CDs
If a CD is soiled, please never clean the CD in the direction of a circle but rather with a soft fluffly cloth from inside to outside. In case of severe layers of dirt we recom- mend to clean the CD with a commercially av ailable CD cleaner. Also in this case do not clean the CD in the direction of a circ le but rather from inside to outside and then let it dry off.
TP
TP
CD
A3
A2

A2
A2
AM/FM
s2e0.5.book Page 6 Wednesday, May 2, 2007 9:14 AM