2009 SKODA OCTAVIA TOUR ECU

The brief instruction
15
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Opening the bonnet– Grip with the hand under
the radiator grille and lift up the bonnet.
– Press the locking lever in direction of arrow
⇒
fig. 15
and lift up the
bonnet.
– Take the bonnet support out of its holder and set it in the opening
designed for it
⇒
fig. 16
.
Further information
⇒page 159, “Opening and closing the bonnet.”.
Inspecting the engine oil level Engine oil
must not
be refilled.
Engine oil
can
be refilled.
Engine oil
must
be refilled.
Further information
⇒page 163, “Check engine oil level”.
Fig. 15 Radiator grille: Locking leverFig. 16 Securing the bonnet with the bonnet support
Fig. 17 Dipstick
AaAbAc
s2g8.b.book Page 15 Tuesday, April 7, 2009 8:53 AM

Unlocking and locking
37
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
It is only possible to start the engine of your car with a Genuine Škoda key with the matching code
⇒page 29.
LockingValid for vehicles without a central locking system: Locking from outside The securing knob will move upwards or downwards in the door when
unlocking

or locking. Locking from inside All closed vehicle doors are
locked by pressing in the securing knobs from the
inside. The doors cannot be opened from the outside when the securing knobs have been pressed in. The vehicle doors ca
n be opened from the inside as follows:
•
the door is unlocked by actu
ating the door-opening lever;
•
The door opens upon actuating the door-opening lever again.Note
•
The opened door cannot be
locked with the securing
knob. This prevents the
possibility of forgetting th
e key in the locked vehicle.
•
The opened side doors at the rear and the front passenger door are locked by
pressing in the securing knob
and slamming the door closed.
•
Please refer to the safety guidelines
⇒page 38.
Child safety lockThe child safety lock prevents the
rear door from being opened from
the inside.The rear doors are equipped with a child safety lock. You can switch the child safety lock on and off using the vehicle key. Switching child safety lock on – Use the vehicle key to turn the slit
in the rear door to the left in the
direction of the arrow
⇒
fig. 36
.
Switching child safety lock off – Use the vehicle key to turn the slit to the right against the direction of
the arrow.
So long as the child safety lock is switched
on it is not possible to open the door
from the inside with the door opening leve
r. In this case the door can be opened
only from the outside.
Fig. 36 Child safety locks on the rear doors
s2g8.b.book Page 37 Tuesday, April 7, 2009 8:53 AM

Unlocking and locking
38
Central locking system*DescriptionUnlocking or locking the vehicle causes
all doors to be unlocked or locked at the
same time by the central locking system. The boot lid is unlocked when opening. It can be opened by pressing the hand grip above the licence plate
⇒page 41, fig. 39
.
Operation of the central locking system is possible:•
from the outside using the vehicle key
⇒page 39,
•
using the button for the central locking system
⇒page 40,
•
by using the remote control
⇒page 42.
•
with the securing knobs in the doors
⇒page 40, fig. 38
- only for vehicles which
are not fitted with electrically operated power windows (only for locking). Warning light and securing knobs in the doors All the securing knob
s move upwards when
unlocking
.
The driver door must be closed when
locking
. Other doors can also be closed after
locking. All the securing knobs move downwards when
locking
. If this is not the case, the
relevant door must be opened
once again and properly closed.
The
warning light
flashes in the driver door, next to the securing knob, to confirm
that the vehicle has been correctly locked.
The warning light will not flash if the safe
securing system is deactivated
⇒page 38.
This is not the case, however, for vehicles
with an anti-theft alarm system* since the
indicator light is showing that the system is active. Convenience operation of windows One can open and close the electrically
powered windows when unlocking and
locking the vehicle
⇒page 45, “Window convenience operation”.
Opening a single door* This function makes it possible to only unlock the driver's door. The other doors remain locked and are only unlock
ed when the command is repeated.
If you wish, you can have a specialist garage
activate the function of the single door
opening mode.
WARNING
Locking the doors prevents involuntary
opening in an exceptional situation
(an accident). Locked doors prevent unwanted entry into the vehicle from outside, for example at road crossings. Locked doors do, however, make it m ore difficult for rescuers to get into
the vehicle in an emergency - danger to
life!
Note
•
In the event of an accident in which the airbags are deployed, the locked doors
are automatically unlocked in order to enable
rescuers to gain access to the vehicle.
•
Only the front doors can be unlocked and locked using the key if the central
locking system fails. You can lock or unlo
ck manually the other doors and the boot
lid.•
Emergency locking of the door
⇒page 40.
•
After locking the vehicle via the central locking system, optically check if all the
doors have been locked - posi
tion of the securing knobs.
Safe securingThe central locking system is equipped with a
safe securing
system. Locking the
vehicle from the outside causes the door lock
s to be automatically
blocked. It is not
possible to open the doors with the door ha
ndle either from the inside or from the
outside. This acts as an effective deterrent for attempts to break into your vehicle. If you lock the vehicle with a key or a remo
te control key, you can deactivate the safe
securing system by locking
two times within 2 seconds.
The warning light in the driver door will not
flash if the safe securing system is deac-
tivated. This is not the case, however,
for vehicles with an anti-theft alarm system* since the
indicator light is showing that the system is active.
s2g8.b.book Page 38 Tuesday, April 7, 2009 8:53 AM

Unlocking and locking
39
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The safe securing system is again activated
the next time the vehicle is unlocked and
locked again. The doors can be opened from the inside
if the vehicle is lo
cked and the safe
securing system is deactivated:•
the door is unlocked by actu
ating the door-opening lever;
•
The door opens upon actuating the door-opening lever again.
WARNING
If the vehicle is locked from the outside and the safe securing system is acti- vated, there must not be any person and
animals in the vehicle as it is then
not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into the vehicle in an emer- gency - hazard!
Note
The anti-theft alarm system* is also activated with the deactivated safe securing system when locking the vehicle. The interior monitor* is however not activated.Unlocking the vehicle using the key
– Turn the key in the locking cylinder of
the driver's door to the left in the
unlock position
⇒
fig. 37
.
– Pull on the door handle and open the door.•
All the doors are unlocked.
•
The boot lid is then unlocked.
•
The switched on interior lights
come on over the door contact.
•
The safe securing system is deactivated.
•
The windows open provided the key
is held
in the unlock position*. On vehicles
fitted with anti-theft alarm system the window operation is only possible 45 seconds after deactivation of the warning system.•
The indicator light in the driver's door stops flashing if the vehicle is not fitted
with an anti-theft alarm system*
⇒page 43.
Note
If the vehicle is equipped with an anti-theft alarm system*, you must unlock the vehicle by inserting the key into the driver door you then have to insert the key into the ignition lock and switch the ignition
on within 15 seconds after unlocking the
door. The
alarm will be triggered
if you do
not switch on
the ignition within 15
seconds.Locking the vehicle with the key– Turn the key in the locking cylinder of
the driver's door to the right in
the lock position
⇒
fig. 37
.
•
All the doors and the boot lid are locked.
•
The switched on interior lights will
switch off over the door contact.
•
The windows and the electric sliding/tilting roof* close provided the key is
held

in the lock position.•
The safe securing system is activated immediately.
•
The indicator light in the driver door begins flashing.
Fig. 37 Turning the key for unlocking and locking the vehicle
AAAB
s2g8.b.book Page 39 Tuesday, April 7, 2009 8:53 AM

Unlocking and locking
40
Note
The opened driver door cannot be locked. It
must be locked sepa
rately after closing
it.Button for the central locking systemIf the vehicle is not locked from outside, you can unlock and lock the vehicle with the button in the driver door. Locking all doors and the boot lid – Press button
⇒
fig. 38
. The symbol
 in the button comes on.
Unlocking all doors and the boot lid – Press button
⇒
fig. 38
. The symbol
 goes out in the button.
The following applies if you have lo
cked your vehicle using the button :
•
It is not possible to open the doors or the boot lid from the outside (safety
feature, e.g. when stopping at traffic lights etc.).•
You can unlock the doors individually from the inside and open them by pulling
the door opening lever.
•
If the driver door is opened, it cannot
be locked; in order to avoid inadvertently
locking the vehicle. You then have to lock
the door separately
after closing them.
•
In the event of an accident in which the airbags are deployed, the locked doors
are automatically unlocked from the inside in order to enable rescuers to gain access to the vehicle.
WARNING
The central locking system al
so operates if the ignition is switched off. All the
doors and the boot lid are locked. Children should never be left unattended in the vehicle since it is difficult to
provide assistance from the outside when
the doors are locked. Locked doors make it difficult for rescuers to get into the vehicle in an emergency - hazard!
Note
The door opening lever and the buttons for the central locking system do not operate if the safe securing system is activated.Emergency locking of the doorsUse the securing knobs in the doors for an emergency locking of the doors
⇒
fig. 38
.
After closing the door, you can no longer open it from outside. If the child safety lock is not switched on, it is possible to
open the door from the inside by pulling
twice on the door handle. If the child safety lock is switched on, it is necesary to also open the door from outside besides pu
lling twice on the inner door handle.
Fig. 38 Button for the central locking system
A1A2
A1
s2g8.b.book Page 40 Tuesday, April 7, 2009 8:53 AM

Unlocking and locking
42
Unlocking and locking carUnlocking the vehicle

– Press button for about 1 second. Locking the vehicle

– Press button for about 1 second.Deactivating safe securing system – Press button twice in 2 seconds. Further information
⇒
page 38.
Folding out of the key – Press button . Folding up of the key – Press button and collapse the key bit in the housing.The turn signal lights flash twice as
confirmation that the vehicle has been
unlocked. The vehicle will lock again auto
matically if you unlock the vehicle using
button but do not open a door or the
boot lid within the next 30 seconds. This
function is intended to prevent the car being unlocked unintentionally.
The safe securing system along with the anti-theft alarm system are, however, deactivated during these 30 seconds. In addition, when the car is unlocked, the el
ectrically adjustable seats and exterior
mirrors* move into the position assigned to this key. The stored setting of driver seat and exterior mirrors is retrieved. The turn signal lights flash once to co
nfirm that the vehicle has been correctly
locked. If the turn signal lights do not fl
ash, check the doors, bonnet and boot lid
again to ensure that they are closed. If th
e doors, the bonnet or the boot lid remain
open when the anti-theft alarm system is activated, the turn signal lights do not flash until after they have been closed. When the vehicle is unlocked or locked, the
interior lights in the door contact are
automatically switched on or off.
WARNING
If the vehicle is locked from the outsid
e and the safe securing system is acti-
vated, there must not be any person in the vehicle as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into
the vehicle in an emergency - hazard!
Note
•
Operate the radio remote control only when the doors and boot lid are closed
and you have visual co
ntact with the vehicle.
•
Once in the car, you must
not press the lock button
 of the radio remote
control before inserting the key into the ignition lock in order to avoid the car being inadvertently locked and the alarm syst
em* being switched on. Should this
happen, press the unlock button
 of the radio remote control.
Synchonisation of the remote controlIf the vehicle cannot be unlocked by actuatin
g the remote control system then it is
possible that the code in the key and the
control unit in the vehicle are no longer
synchronised. This can occur when the buttons on the radio-operated key are actu-
Fig. 40 Folding key with radio remote control
A1A2A2A3A3
A1
s2g8.b.book Page 42 Tuesday, April 7, 2009 8:53 AM

Unlocking and locking
43
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
ated a number of times outside of the operative range of the equipment or the battery on the remote control was replaced. This means it is necessary to synchronise the code as follows:•
Press any button on the remote control.
•
pressing of the button means that the door will unlock with the key within 1
minute.Anti-theft alarm system*DescriptionThe anti-theft alarm system increases the le
vel of protection against people seeking
to break into the vehicle. The system tri
ggers audible and visual warning signals if
an attempt is made to break into the vehicle. Optical and acoustic signals alert if an al
arm has been triggered (the turn signal
lights flash and the signal horn honks). How is the alarm system activated? The anti-theft alarm system is activated
automatically when th
e vehicle is locked
with the key on the closed driver's door or
by using the radio remote control. It is
activated 30 seconds after locking the door. How is the alarm system deactivated? The anti-theft alarm system is deactivated
if the vehicle is unlocked by only using
the radio remote control. The vehicle is au
tomatically locked agai
n if the vehicle is
not opened within 30 seconds after reac
tivating the anti-theft alarm system.
Once you unlock the vehicle by inserting the key into the driver door you then have to insert the key into the ignition lock an
d switch the ignition on within 15 seconds
after unlocking the door in order to deac
tivate the anti-theft alarm system. The
alarm will be triggered
if you do
not switch on
the ignition within 15 seconds.
When is the alarm triggered? The following security areas of the locked vehicle are monitored:•
Bonnet,
•
Boot lid,
•
Doors,
•
Ignition lock,
•
Vehicle interior
4),
•
A drop in voltage of the on-board power supply.
An alarm is immediately triggered if either of the two battery terminals is discon- nected while the anti-theft
alarm system is activated.
Deactivation of interior monitor The process of switching off and switching on the interior monitoring system is the same as for switching off and switching on the safe securing system
⇒page 38.
This function makes it possible for example to leave animals in the vehicle. How is the alarm switched off? You switch the alarm off if you unlock the
vehicle with the radio remote control or
if you switch the ignition on.
Note
•
The working life of the alarm siren is 5 years. More detailed information is avail-
able by a specialist garage.•
Before leaving the car, check that all the doors, windows and the electric
sliding/tilting roof* are properly closed in order to ensure that the anti-theft alarm system is fully operational.•
Coding of the radio remote control and
the receiver unit precludes the use of
the radio remote control from other vehicles.4)The alarm will be triggered through movement of
occupants within the interior of the vehicle
or an attempt to steal the radio. The rear part of the interior of the vehicle is not fully moni-tored under certain circumstances.
s2g8.b.book Page 43 Tuesday, April 7, 2009 8:53 AM

Lights and Visibility
57
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Switching windscreen wipers off – Move the lever back into its home position .The windscreen wipers and the windscreen washer system only operate if the igni- tion is switched on. The rain sensor* automatically regulates
the break between the individual wiper
strokes depending on the intensity of the rain. The windscreen washer nozzles are heated* when the ignition is switched on.Top up with wash liquid
⇒page 172.
WARNING
•
Properly maintained windscreen wiper
blades are essential for clear visi-
bility and safe driving
⇒page 57, “Replacing wiper blades for the wind-
screen wipers”.•
Do not use the windscreen washer sy
stem at low temperatures, without
heating the windscreen beforehand. Otherwise the window cleaner could freeze on the windscreen and re
strict the view to the front.
•
The rain sensor only operates as a
support. The driver is not released
from the responsibility to set the function of the windscreen wipers manu- ally depending on the visibility conditions.
Caution
In frosty weather, please first of all check whether the windscreen wiper blades are not frozen to the windscreen before swit
ching them on. Switching on windscreen
wipers when the blades are frozen to the windscreen may result in damage both to the blades and the motor of the windscreen wipers!
Replacing wiper blades for the windscreen wipersTaking off the wiper blade – Fold windscreen wiper arm out from
the windscreen and position the
wiper blade at right angles to the wiper arm
⇒
.
– Press the securing spring in the direction of arrow and press the
wiper blade at the same time to th
e windscreen - Warning, danger
of breaking the windscreen.
⇒
fig. 56
⇒
.
Attaching a wiper blade – Clip the securing spring until it is
heard to lock in the windscreen wiper
arm.
– Check whether the wiper blade is correctly attached.Wiper blades in proper condition are esse
ntial to obtain good visibility. Wiper
blades should not be allowed to become
dirtied by dust, insect remains and
preserving wax. Juddering or smearing of the wiper blades
could then be due to wax residues left
on the windscreen by vehicle washing in
automatic vehicle wash systems. It is
therefore important to
degrease
the lips of the wiper blades after every pass
through an
automatic vehicle wash system
.
A0
Fig. 56 Wiper blade for the windscreen wiper
AA
AB
s2g8.b.book Page 57 Tuesday, April 7, 2009 8:53 AM