2009 SKODA OCTAVIA TOUR ECU

Seat belts
112
Taking seat belts off– Press the red button in the belt lock
⇒
fig. 119
. The spring force causes
the tongue of the lock to jump out.
– Guide the belt back with your hand
to enable the inertia reel to wind
up the belt webbing more easily.
A plastic knob in the belt webbing holds the belt tongue in a position which is easy to get hold of.Three-point seat belt with the Interlock System*A three-point safety belt with the Interlock System is used on some vehicles instead of a pelvic belt. If the backrest of the rear seats is not secured, the retractor blocks and the seat belt cannot be reeled down.
Rear middle three-point safety belt with safety lock for a child seat*In order to attach a child seat the rear
middle three-point safety belt with
the blocking, the so-called chil
d safety locks, can be used.
Switching child safety lock on – Attach the child safety seat with the three-point seat belt (self-
retracting) as stated in the manufacturer's instructions.
– Reel up the shoulder part of the
belt completely. When the belt is
reeled up, this can be detected by a “clicking” noise.
– After fixing the child seat in place, let the belt freely reel up. Now the
belt can no longer be reeled down.
– Check if the safety lock is activated by pulling on the belt. Switching child safety lock off – By pressing the button in the lock of
the safety belt, the blocking is
unblocked and afterwards the safety belt starts to reel up.
– After fully reeling up the belt, you can freely reel it down again.
Fig. 119 Releasing lock tongue from belt lock
s2g8.b.book Page 112 Tuesday, April 7, 2009 8:53 AM

Transporting children safely
123
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Transporting children safelyWhat you should know about transporting children!An introduction to the subject Accident statistics have revealed that children are generally more safely transported on the rear seat
s than on the fron
t passenger seat.
Children younger than 12 years of age should
normally travel on the rear seat of the
vehicle (take note of any na
tional legal provisions which differ from this). They
should be secured there by means of a child restraint system or by using the existing seat belts depending on their age, body si
ze and weight. The child seat should be
mounted behind the front passen
ger seat for safety reasons.
The physical principle of an accident do
es, of course, also apply to children
⇒ page 109, “The physical principle of a fronta
l collision”. They differ from adults in
that their muscles and bone structure of ch
ildren are not yet fully developed. Thus
children are exposed to increased risk of injury. Children should be transported by using special child safety seats in order to reduce this risk of injury. Use only child safety seats which are offici
ally approved and are suitable for chil-
dren and which comply with the ECE-R 44
standard, which classifies child safety
seats into 5 groups
⇒page 126, “Classification of child seats into groups”. Child
restraint systems which have been tested for conformity to ECE-R 44 standard have a non-detachable test seal (a large E within
a circle and below this the test number)
attached to the seat. We recommend that you use ch
ild safety seats from the Škoda genuine accessories.
These child seats were developed and also
tested for use in Škoda vehicles. They
fulfil the ECE-R 44 standard.
WARNING
Always comply with legal provisions and instructions from the relevant child safety seat manufacturer when in
stalling and using the child seat
⇒
in
“Important safety information regarding the use of child safety seats”.
Note
Any varying national legal regulations take priority over the information provided in these instructions for use, or stated in this chapter.Important safety information regarding the use of child safety seats Correct use of child safety seats
considerably reduces the risk of
injury!
WARNING
•
All the occupants of the car - in particular children - must wear a seat belt
when the car is moving.•
Chi ld re n le s s tha n 1. 5 0 m i n h e ig ht
or younger than 12
years must not use
a normal seat belt withou
t a child restraint system otherwise this may result
in injuries to the stomach and neck areas. Comply with the national legal requirements.•
One should never carry children, and also not babies! - on one's lap.
•
You can transport a child safely in
a suitable child safety seat
⇒page 126,
“Child seat”!•
Only one child may be fastened with a seat belt into a child safety seat.
•
Never leave the child sitting unattended in the seat.
•
Certain outside climatic conditions can cause life-threatening tempera-
tures in the vehicle.•
Never allow your child to be transported in a vehicle without the use of a
suitable restraint system.•
Children should also never stand up in a vehicle or kneel on the seats
when the vehicle is moving. In the even
t of an accident the child will be
thrown through the vehicle and may as a
result suffer fatal injuries, and also
injure other occupants.
s2g8.b.book Page 123 Tuesday, April 7, 2009 8:53 AM

Towing a trailer
144
Towing a trailerTo w i n g a t r a i l e rTechnical requirements The towing device must satisfy
certain technical requirements.
Your vehicle is designed primarily for tr
ansporting persons and luggage. It can,
however, also be used for towing a traile
r - provided certain te
chnical equipment is
fitted. If your vehicle has already been supplied with a
factory-fitted
towing device then
everything that is necessary
for towing a trailer in technical terms, and in terms of
the law, has already been taken into account. Your vehicle is fitted with a 13-pin po
wer socket for the electrical connection
between the vehicle and trailer. If th
e trailer which you wish to tow has a
7-pin
connector
, you can use a suitable adapter
5) from Škoda original accessories.
This work must be carried out in accordan
ce with the manufacturer's specifications
if a towing device is retrofitted. Specialist garages are familiar with details
relating to retrofitting a towing device
and for any necessary modifications to the cooling system.
WARNING
We recommend that you have the towing device from Škoda original acces-sories installed by a specialist garage.
He is familiar with all the relevant
details relating to retrofitting such equi
pment. There is a risk of an accident
if the towing device is not properly fitted!
General Maintenance There are a number of points to
pay attention to when towing a
trailer.Trailer load The permissible trailer load must
on no account be exceeded.
You can negotiate appropriatel
y steeper inclines and desc
ents if you do not make
full use of the perm
issible trailer load.
The trailer loads specified only apply for
altitudes
up to 1 000 metres above mean
sea level. The fact that the engine power ou
tput drops with increasing height due to
a lowering of air pressure and thus the abil
ity to climb, means that the towed weight
must be reduced by 10% for every further increase of 1 000 metres in height above sea level. The towed weight is the weight of the (laden) vehicle and the (laden) trailer together. One should take this into account before driving up to higher alti- tudes. The trailer and drawbar load information on the type plate of the towing device are merely test data for the tow
ing device The data relating to your
vehicle, which is often less than this test data, can be found in your vehicle registration documents. Distribution of the load Distribute the load in the trailer in such a way that any heavy items are located as close as possible to the axle. Secure
the items to prevent them slipping.
Tyre inflation pressure Select the tyre inflation pressure on your vehicle for that of “fully laden”, ⇒ page 173. The inflation pressure of the tyres fitted to the trailer adjust in accord- ance with the manufacturer's recommendation. Exterior mirrors You have to have additional
exterior mirrors fitted if you are not able to see the
traffic behind the trailer with the standard rear-view mirrors. Both exterior mirrors
5)In some countries the adapter is
supplied with the towing device.
s2g8.b.book Page 144 Tuesday, April 7, 2009 8:53 AM

Fuel
156
Operation in winterWinter-grade diesel fuel A different grade of diesel fuel is available at
filling stations in winter than during the
summer. Using “summer-grade diesel fuel” at
temperatures below 0°C can result in
operational problems because the diesel be
comes viscous as a result of paraffin
separation. It is therefore the case that EN 590 prescribes diesel fuel class for certain periods of the year which can also be purchased at
the corresponding time during the year.
“Winter-grade diesel fuel” will still operate properly even at a temperature of -20°C. It is often the case in countries with diff
erent climatic conditions that diesel fuels
available have a different temperature characteristic. The specialist garages and the filling stations in the country concerned wi
ll be able to provide you with informa-
tion regarding the diesel fuels available. Prewarming fuel The vehicle is fitted with a fuel filter prewarming system. This secures operation of a vehicle using diesel fuel down to an environmental temperature of -25°C.
Caution
It is not permitted to add the various fuel
additives on the market, including petrol,
to diesel fuel in order to
improve its flow properties.
RefuellingThe filler tube of the fuel reservoir is
located in the rear right side part of
the vehicle. Opening the fuel filler cap – Open the fuel filler flap with the hand. – On vehicles without remote unlocking
of the fuel filler flap from the
driver's seat, unlock the fuel filler cap on the fuel filler tube by turning the vehicle key to the left.
Fig. 145 Switch for opening the fuel filler flap from the driver seatFig. 146 Fuel filler flap with cap unscrewed
s2g8.b.book Page 156 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
159
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Inspecting and replenishingEngine compartmentBonnet remote releaseBonnet remote release – Pull the unlocking lever below the
dash panel on the driver's side
⇒
fig. 148
.
The bonnet jumps out of its lock as a result of the spring force.
Note
Ensure that the windscreen wiper arms
are not folded out before opening the
bonnet otherwise damage coul
d occur to the paintwork.
Opening and closing the bonnet.Opening the bonnet – Unlock the bonnet
⇒
fig. 148
.
– Grip with the hand under the radiat
or grille and lift up the bonnet.
– Press the locking lever in direction of arrow
⇒
fig. 149
and lift up the
bonnet.
Fig. 148 Bonnet release lever
Fig. 149 Radiator grille: Locking leverFig. 150 Securing the bonnet with the bonnet support
s2g8.b.book Page 159 Tuesday, April 7, 2009 8:53 AM

Inspecting and replenishing
160
– Take the bonnet support out of its holder and set it in the opening
designed for it
⇒
page 159, fig. 150
.
Closing the bonnet – Lift the bonnet slightly and unhook the bonnet support. Press the
bonnet support into the hold
er designed to hold it.
– Allow the bonnet to drop from a height of about 30 cm into the lock -
bonnet
do not press down on it
!
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of
the engine compartment - risk of scaldi
ng! Wait long enough until the steam
or coolant has stopped escaping.•
For safety reasons, the bonnet must always be properly closed when
driving. One should therefore check that
the lock has in fact engaged prop-
erly after closing the bonnet.•
Stop your vehicle i
mmediately while driving if yo
u notice that the lock is
not properly engaged and close the bonn
et properly - risk of an accident!
Working in the engine compartment Particular care is required when ca
rrying out any work in the engine
compartment!There is a risk of injuries, scalding,
accidents and fire wh
en working in the
engine compartment, e.g. inspecting an
d replenishing oil and other fluids. For
this reason, it is essential to comply with the warning instructions stated below and with the general applicable
rules of safety. The engine compart-
ment of your car is a hazardous area
⇒
.
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of
the engine compartment - risk of scaldi
ng! Wait long enough until the steam
or coolant has stopped escaping.•
Switch off the engine and pull out the ignition key.
•
Apply the handbrake firmly.
•
On vehicles fitted with a manual gearbox, move the gearshift lever into
Neutral.•
Allow the engine to cool down.
•
Keep children clear of the engine compartment.
•
Never spill oil and other fluids over the hot engine. Such fluids (e.g. the
antifreeze contained in the coolant) may ignite!•
Avoid short circuits in the electrical system - particularly on the battery.
•
Never place your hand into the radiator
fan as long as the engine is still
warm. The fan might suddenly start running!•
Never open the cap of the coolant expa
nsion bottle as long as the engine
is still warm. The cooling system is pressurized!•
Cover over the cap of the coolant expansion reservoir with a large cloth
when opening it as protection for your face, hands and arms from hot steam or hot coolant.•
Do not let objects, such as e.g cleaning cloth or tools lie in the engine
compartment.•
If you wish to work under the vehicl
e, you must secure the vehicle from
rolling away and support it
with suitable supporting blocks; the lifting jack*
is not sufficient for this - risk of injury!•
In cases where it be necessary to carry out inspection work when the
engine is running there is an additional risk from rotating parts (e.g. the V- ribbed belt, alternator, radiator fan) and from the high-voltage ignition system. Please observe in addition the following:
− Never touch the electrical cabl
es of the ignition system.
− Absolutely avoid any jewellery, loose items of clothing or long hair from getting into the rotating part
s of the engine - Hazard! Therefore
s2g8.b.book Page 160 Tuesday, April 7, 2009 8:53 AM

Breakdown assistance
182
Vehicle tool kitThe vehicle tool kit and the lifting jack* are stowed in a box in the spare wheel* ⇒ fig. 163
; there is also space here for the de
tachable ball head of the towing
device*. The box is attached with a strap on the spare wheel*. The vehicle tool kit contains the following parts (depending on equipment fitted):•
Wire clamps for removing
the full wheel trims,
•
Screwdriver,
•
Plastic clip for a wheel bolt cover,
•
Wheel wrench*,
•
Towing eye,
•
Adapter for the safety wheel bolts*.
Before placing the lifting jack* back in its
storage area, screw in the arm of the lifting
jack fully.
WARNING
•
The factory-supplied lifting jack* is
only intended for your model of
vehicle. On no account attempt to lift
a heavier vehicle or other loads - risk
of injury!•
Ensure that the vehicle tool kit is safely attached in the luggage compart-
ment.
Note
Ensure that the box is alwa
ys secured with the strap.
Spray for repairing a tyre*The spray for repairing a tyre is intended fo
r rapid repair of small defects in a tyre
consisting of a damage up to a si
ze of up to 5 mm. The spray is
not at all intended
to replace a permanent repair on the tyre
; this repair serves to reach the work-
shop. The repair can be undertaken on the vehicl
e immediately. Please read the attached
instructions carefully before the repair. The spray for repairing a tyre is located in
the right front well of the plastic part
behind the spare wheel.Tyre repair kitThe tyre repair kit is intended for the repair of minor tyre defects. The tyre repair kit contains a compressor, inflation bottle, operating instructions and accessories. The repair with the
tyre repair kit is
not at all intended to replace
a permanent
repair on the tyre, this repair only serves
to reach the next specialist garage. The
Fig. 163 Luggage compart- ment: storage compartment for vehicle tool kit
Fig. 164 Vehicle tool kit: Spray for repairing a tyre
s2g8.b.book Page 182 Tuesday, April 7, 2009 8:53 AM

Breakdown assistance
184
prescribed distance from your vehicl
e while observing all national legal
provisions. In this way you are protecting not only yourself but also other road users.•
Never start the engine with the vehicle
sitting on the raised jack - danger
of suffering injury.
Caution
If you have to change a wheel on a slope
first block the opposite wheel with a stone
or similar object in order to secure th
e vehicle from unexpectedly rolling away.
Note
Comply with the national legal regulations.Changing a wheelAlways change a wheel on a level surface as far as possible. – Take off the full wheel trim*
⇒
page 185 or the caps
⇒
page 185.
– In the case of light alloy wheels remove the wheel trim cap
⇒
page 186.
– Slacken the wheel bolts
⇒
page 186.
– Jack up the vehicle until the wheel to
be changed is clear of the ground
⇒
page 187.
– Unscrew the wheel bolts and place them on a clean surface (cloth,
paper etc.).
– Take off the wheel.– Fit on the new spare wheel* and tighten the wheel bolts slightly. –Lower the car.
– Tighten the wheel bolts firmly, al
ternately and diagonally using the
wrench* (crosswise)
⇒
page 186.
– Mount the full wheel trim/w
heel trim cap or the caps.
Note
•
All bolts must be clean
and must turn easily.
•
You must never grease or oil the wheel bolts!
•
When fitting on unidirectional tyres, ensure that the tyres rotate in the correct
direction
⇒page 173.
Subsequent stepsAfter changing the wheel, you must perform the following steps. – Stow and attach the replaced wheel in the spare wheel well. – Stow the vehicle tool kit in the space provided.–
Check
the
tyre pressure
on the spare wheel* just mounted as soon
as possible.
– Have the
tightening torque
of the wheel bolts
checked
with a torque
wrench as soon as possible. Steel and light alloy wheels must be tight-ened to a tightening torque of
120 Nm
.
– Have the defective tyre repaired as soon as possible.
WARNING
It is necessary to observe the guidelines given on
⇒page 175, “New tyres
and wheels” if the vehicle is subseq
uently fitted with tyres which are
different to those it was fitted with at the works.
WARNING (continued)
s2g8.b.book Page 184 Tuesday, April 7, 2009 8:53 AM