2009 SKODA OCTAVIA Headlight

Taking care of your vehicle and cleaning the vehicle
214
Plastic partsExternal plastic parts are cleaned by norm
al washing. Plastic
parts and synthetic
leather can also be treated with
special solvent-free plastic cleaning agents
if a
damp cloth is not sufficient. Paint care pr
oducts are not suitable for plastic parts.
Caution
Solvent-free cleaners attack th
e material and can damage it.
WindowsOnly use a plastic ice scraper for removing snow and ice from the windows and mirrors. You should not move the ice scraper forward and backward but in one direction on the window which you are clea
ning in order to avoid any damage to
the surface of the glass. You can best remove residues of rubber,
oil, grease, wax or
silicone by using a
special window cleaner or a special silicone remover. You should also clean the windows regularly from the inside.Do not use window leathers
which you have used to polish the vehicle body to dry
off the windows. Residues of preservati
ves in the window leather can dirty the
window and reduce visibility. Do not affix any stickers over the inside of the rear window to avoid damage to the heating elements of the rear window heater
.
We recommend using a preservative from
Škoda genuine accessories offered by
your Škoda dealer.
Caution
Never remove snow or ice from the glass
parts with warm or hot water - risk of
formation of cracks in the glass!
The headlight lensesPlease do not use any aggres
sive cleaning or
chemical solvent pr
oducts - risk of
damage to the plastic lenses
Please use
soap and clean warm water.
Caution
Never
wipe the headlights dry and do not
use any sharp objects for cleaning the
plastic lenses, this may result in damage
to the protective paintwork and conse-
quently in formation of cracks on the head
light lenses, e.g through effect of chem-
ical products.Door and window sealsThe rubber seals on the doors, boot lid,
bonnet and windows remain supple and
last longer if you treat them from time to
time with a rubber care product (e.g. with
a spray with silicone-free oil). You also avoid premature wear of the seals and prevent leakages in this way. It is also easier to open the doors. Rubber seals which are well cared for also do not stick together in cold winter weather.Locking cylinderWe recommend that you use the spray from Škoda original accessories with regreasing and anticorrosive effect
for de-icing lo
cking cylinders.
Note
When washing your vehicle, ensure that as
little water as possible gets into the
locks.
se0.1.book Page 214 Frida
y, April 10, 2009 3:19 PM

Inspecting and replenishing
236
A discharged battery may already
freeze
at temperatures just below 0°C
⇒
. We
recommend that you no longer use a ba
ttery which has thawed out because the
casing of the battery may be cracked thro
ugh the formation of ice and this would
allow battery electrolyte to flow out. The vent plugs of the battery should not be opened for charging.
WARNING
•
Never charge a frozen or thawed battery - risk of explosion and caustic
burns. Replace a frozen battery.•
Never charge a battery which has a to
o low electrolyte level - risk of
explosion and caustic burns.Disconnecting and reconnecting the batteryOn disconnecting and reconnecting the batte
ry the following functions are initially
deactivated or are no longer able to operate fault-free. We recommend having the vehicle checked
by a Škoda Service Partner to ensure
full functionality of all electrical systems.Replacing the batteryYou should only replace a battery with a
new battery of the same capacity, voltage
(12 V), amperage and of the same size. Škoda Service Partners have a range of suit- able batteries available.
We recommend that you only have an ol
d battery disposed of by your Škoda
Service Partner since it does require special disposal.
For the sake of the environment
Batteries contain poisonous substances such
as sulphuric acid and lead. They must
be disposed of in accordance with loca
l environmental protection regulations and
on no account as domestic waste.Windshield washer systemThe windshield washer reserv
oir contains the cl
eaning fluid for th
e windscreen or
rear window and for the headlamp cleaning system*. The reservoir is located at the front right of the engine compartment
⇒fig. 217
.
The
filling level
of the container is 3 litres, 5.5 li
tres on vehicles which also have a
headlight washing system. Clear water is not sufficient to intensively clean the windscreen and headlights. We therefore recommend using clean washing water together with the screen cleaner from Škoda genuine accessories (in winter
additionally with antifreeze) which is
capable of removing stubborn
dirt. Follow the instructio
ns for use on the packaging
when using screen cleaning products. You should always add antifreeze to the
cleaning water in winter even if your
vehicle is fitted with heated
windscreen washer nozzles*.
Operation
Operating measure
Electrical power window (operational faults)
⇒page 55
Enter radio code number
see Radio Operating Instructions
Set hours
⇒page 21
Data in the multi-functional indicator* are deleted.
⇒ page 21
Fig. 217 Engine compart- ment: Windshield washer fluid reservoir
se0.1.book Page 236 Frida
y, April 10, 2009 3:19 PM

Inspecting and replenishing
237
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
It is also possible in exceptional cases to use methylated spirits when no screen cleaner with antifreeze is available. The concentration of methylated spirits must not be more than 15 %. Please note, howeve
r, that the antifreeze protection at this
concentration is only adequate down to -5°C.
WARNING
Read and observe the warning notes
⇒page 225, “Working in the engine
compartment” before working in the engine compartment.
Caution
•
On no account should you add radiator
antifreeze or other additives to the
windscreen washer fluid.•
If the vehicle is fitted with headligh
t cleaning system, you should only add
cleaning products which do
not attack the poly
carbonate coating of the headlights
to the windscreen washer fluid. Please co
ntact your Škoda Service Partner, who will
tell you which cleaning agent you can use.
se0.1.book Page 237 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
254
Driver of the towing vehicle – Do not drive off until the tow rope is taught. – Release the clutch particularly gent
ly when starting off or depress the
accelerator particularly gently if yo
ur vehicle is fitted with an auto-
matic gearbox.
Driver of the towed vehicle – Switch the ignition on so that the steering wheel is not blocked and
you can also operate the turn signal
lights, the headlight flasher, the
windscreen wipers and wi
ndscreen washer system.
– Take the vehicle out of gear or move
the selector lever into position
N
if your vehicle is fitted with an automatic gearbox.
– Note that the brake servo unit and power steering only operate if the
engine is running. You will require si
gnificantly greater physical force
to depress the brake pedal and to steer the vehicle if the engine is not running.
– Ensure that the tow rope is always kept taught.Tow rope or tow bar A tow
bar
is safest way of towing a vehicle and also minimizes any shocks. You can
use a tow
rope
only if a suitable tow bar is not available.
The tow rope must be elastic to protect
the vehicle. Thus one should only use
plastic fibre rope or a rope made
out of a similarly elastic material.
Only attach the tow rope to the
towing eyes
provided for this purpose
⇒page 254
and
⇒page 256.
Driving style Towing another vehicle requires a certain
amount of practice. Both drivers should
be familiar with the particular points
about towing a vehicle. Unskilled drivers
should not attempt to tow in another vehicle or to be towed in. One should be constantly vigilant not to allow impermissibly high towing forces or jerky loadings. There is always a risk of excessive stresses and damage resulting at
the points to which you attach the tow ro
pe or tow bar when you attempt to tow a
vehicle which is not standing on a paved road.
Caution
If the gearbox of your vehicle no longer
contains any oil because of a defect, your
vehicle must only be towed in with the driven wheels raised clear of the ground, or on a special vehicle transporter or trailer.
Note
•
Please comply with any legal requirements particularly regarding the switched
on signal systems, when towing in
or tow-starting another vehicle.
•
The tow rope must not be twisted as it may in certain circumstances result in the
front towing eye being unscrewed out of your vehicle.Front towing eye The towing eye is stored in the box for the vehicle tool kit.
Fig. 231 Front bumper: Protective grille
se0.1.book Page 254 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
260
Fuse assignment in the dash panelCertain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
F13
Engine control unit
15/30
F14
Ignition
20
F15
Lambda probe NO
x sensor, fuel pump relay
Glow plug system relay
10 15 5
F16
Central control unit, right main headlight, right rear light unit
30
F17
Horn
15
F18
Amplifier for digital sound processor
30
F19
Front window wiper
30
F20
Water pumpvalve for fuel dosing
1020
F21
Lambda probe
10/15
F22
Clutch pedal switch, brake pedal switch
5
F23
Secondary air pump Air mass meter Fuel high pressure pump
5 10 15
F24
Activated charcoal filter, ex
haust gas recirculation valve
10
F25
Pump for ABS
30/40
F26
Central control unit, left main headlight, left rear light unit
30
F27
Secondary air pump Glow plug system
4050
F28
Not assigned
F29
Power supply terminal 30
50
F30
Te r m i n a l X
a)
50
a)In order not to drain the battery unnecessarily
when starting the engine, the electrical com-
ponents of this terminal are automatically switched off.No.
Power consumer
Amperes
No.
Power consumer
Amperes
1
Diagnostic socket, Engine co
ntrol unit, Electrical fuel
pump
10
2
Control unit for ABS, ESP
5
3
Airbag
5
4
Heating, Air conditioning system, Reversing lights
5
5
Control unit for headla
mp beam adjustment
5
6
Instrument cluster, Control unit for automatic gearbox, Control unit for electromec
hanical power steering,
Parking aid; Haldex clutch
5
7
Not assigned
8
Not assigned
9
Not assigned
10
Not assigned
11
Not assigned
Fig. 240 Schematic repre- sentation of the fuse carrier in the dash panel
se0.1.book Page 260 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
261
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Electrically adjustable
seats are protected by
automatic circuit breakers
, which
switch on again automatically after a fe
w seconds after the overload has been
eliminated.BulbsChanging bulbsThe relevant lamp must always be switch
ed off before a light bulb is replaced.
Defect light bulbs should only be replaced
with light bulbs of the same type. The
designation is located on the light socket or the glass bulb. Changing certain bulbs is not something wh
ich you can do yourself, but requires to
be done by a specialist. Other parts of the vehicle must be removed in order to
12
Central locking control unit
10
13
Diagnostic socket, Light switch
10
14
Control unit for automatic gearbox, Selector lever lock
5
15
Central control unit - interior lights
5
16
Climatronic
10
17
Not assigned
18
Not assigned
19
Control unit for trailer detection
5
20
Not assigned
21
Cornering lights for the left and right side
10
22
Air blower for Climatronic
40
23
Front power window
30
24
Cigarette lighter
25
25
Rear window heaterRear window heater, Auxiliar
y heating (auxiliary heating
and ventilation)
2530
26
Power socket in the luggage compartment
20
27
Fuel pump relay, Injection valves (diesel engine)
15
28
Not assigned
29
Engine control unit, Crankcase ventilation heater
10
30
Control unit for automatic gearbox
20
31
Vacuum pump
20
32
Rear power window
30
33
Electric sliding/tilting roof
25
34
Control unit for convenience functions
20
35
Anti-theft alarm system
5
No.
Power consumer
Amperes
36
Headlight cleaning system
20
37
Front seat heating
30
38
Heated rear seats
30
39
Not assigned
40
Air blower for heating and air conditioning
40
41
Rear window wiper
15
42
Not assigned
43
Towing device
15
44
Towing device
20
45
Towing device
15
46
Heated windscreen washer nozzles
5
47
Relay for auxiliary heating
5
48
Not assigned
49
Light switch
5
No.
Power consumer
Amperes
se0.1.book Page 261 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
262
change the light bulbs. This applies, in
particular, to bulbs which can only be
reached from the engine compartment. We therefore recommend that you have any bulbs changed by an authorised Škoda Service Partner or, in exceptional cases, by
calling on other professional assistance.
Please note that the engine compartment is a hazardous area
⇒page 225,
“Working in the engine compartment”. We recommend that you always have a small box of replacement bulbs in your vehicle. You can obtain replacement bulbs from Škoda original accessories or from a specialist garage
23).
The set of light bulbs can be stowed in the locable box in the spare wheel.Fitted with a xenon headlightChange of light bulbs on Xenon lights (low beam lights, parking lights and main beam lights) should be undertaken by a specialist garage. Overview of bulbs23)The small box with replacement bulbs is part of
the basic equipping of the vehicle in some
countries.Front headlight
Halogen headlight
Xenon headlight
Low beam light
H7
D1S
Main beam light
H1
Parking lights
W5W/W5W BL
Daylight driving lights*
PY21W SLL/LED
a)
a)Octavia RS, Octavia ScoutTurn signals
PY21W
Fog lights
H8/HB4
a)
Light unit (Octavia)
Bulb
Reversing light
P21W
Tu r n s i g n a l s
PY21W
Twin filament light bulb for the brake lights and tail lights
P21/4W
Twin filament light bulb for the rear fog lights and tail lights
P21/4W
Parking lights
W3W
Rear light unit (Combi)
Bulb
Reversing lights, brake lights, tail lights and rear fog light
P21W
Tu r n s i g n a l s
PY21W
Parking lights
W3W
Others
Bulb
Side turn signal lights
LED
Licence plate light
C5W
3. Brake light
LED
Entry lighting
W5W
front interior lighting
C10W
Reading lights
W5W
Rear interior lighting
C10W
Luggage compartment light
W5W
Door warning light
C5W
Lighting in storage compartment
C3W
se0.1.book Page 262 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
263
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
Bulbs H7 and H1 are pressurised and
may burst when changing the bulb
- risk of injury!•
It is recommended to wear gloves
and eye protection
when changing a
light bulb.•
Gas discharge bulbs* (xenon bulbs) operate with a high voltage, profes-
sional knowledge is required - danger to life!
Caution
Do not take hold of the glass bulb with
naked fingers (even the smallest amount of
dirt reduces the working life of the light bu
lb). Use a clean cloth, serviette or some-
thing similar.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed that no major complications wi
ll arise. Other light bulbs should be replaced by your
specialist garage.Front headlight
Positions of the light bulbs in the front headlight
⇒fig. 241
.
- Front turn signal light - parking lights and low beam - main beam lightRemoving the headlightThe headlight must be removed in order to change the light bulb of the parking lights, low beam lights and main beam lights as well as the turn signal lights. Removing the headlight – Switch the ignition and all lights off. – Open the bonnet
⇒
page 224.
– Unscrew the plastic nut
⇒
fig. 242
.
– Pull the fuse in upward direction. – Pull the locking lever of the headlight as far as the stop in the direction
of arrow .
Fig. 241 Front headlight: Installing the light bulbs
AAABAC
Fig. 242 Front headlight: Installing the light bulbs
AA
AB
A1
se0.1.book Page 263 Frida
y, April 10, 2009 3:19 PM