2009 SKODA OCTAVIA Amundsen Navigation System Manual

General information
7
Operation when driving The demands of today's road traffic require full concentration from all road users at all times.
WARNING
•
Always concentrate fully on your driv
ing. Inattention by the driver can
lead to accidents and injuries.•
Do not allow yourself to be distracted by trying to use the unit, concen-
trate instead on the traffic situation.•
Use the unit only if road, weather and traffic conditions permit and you
will not be distracted.•
The various volume settings must be selected in such a way that audible
signals from the outside, su
ch as e.g. a Martins horn from police cars and fire
brigade, can be heard at all times.
Note
Depending on the country, some functions
of the radio navigation system can no
longer be selected on the screen at cert
ain speeds. This is not a malfunction, but
corresponds to the legal requirem
ents of this particular country.
Special functionsParking aid* If your vehicle is equipped wi
th “parking aid” and after it is activated, the distance
to the obstacle is shown on the screen. Climatronic* If your vehicle is equipped with climatroni
c, a feedback is received on the screen
when changing the settings.
Personalisation Your vehicle can be eq
uipped with up to four keys. Ind
ividual settings of the unit are
always assigned to the key,
which is currently inserted in the ignition lock. In prac-
tice, this means that each time you use another vehicle key, the setting of the unit which is assigned to the key is carried out.Switching the system on and off– The system is switched on or off by pressing the control button .The last active audio source before switching off is repeated. If the key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. You can then switch
the unit on again. If the ignition is
switched off, the system switches off au
tomatically after approx. half an hour
(vehicle battery protection
against discharging). This pr
ocess can be repeated as
often as necessary.General - operationThe screen of the unit is a so-calle
d touch screen (touch-screen). Fields
circled in colour on the touch-screen
are presently “active” and are oper-
A1
BAT-20H1069
Fig. 2 Menu radio
s36c.b.book Page 7 Thursday, April 9, 2009 2:50 PM

General information
8 ated by touching the screen. Active
fields, which call up a function or a
menu, are called “
function buttons
” / .
The following information is displayed in the main menu: the selected radio station (i
ts frequency or
designation);
selected waveband; activation for the rece
ption of traffic reports;
current menu. “Pop-up window” If you press the function key on the sc
reen, a so-called “pop-up window” will
open where all possible se
t-up options are displayed.
Briefly press the desired set-up option. Th
e pop-up window will disappear and the
newly selected set-up option is
displayed in the function key.
“Check box” Some functions can only
be switched on or off.
There is a so-called “check box” in front of a function which can only be switched on or off. A tick in the check box
7 indicates that the functi
on is switched on, an
empty check box
8, indicates that it
is switched off.
Briefly press the corresponding function key for switching on or off.
Input mask for free text inputIn some of the menus you can enter a free text, for example, when entering a new destination or while se
arching for the name of a point of
interest. – Press to accept a character se
quence offered by the system or
press in order to delete the characters in the entry line.
– When in the entry window, press on a character shown on the keypad
block to accept it into the entry line.
– You can also delete or change the character sequence in the entry line
as well as insert additional characters.
Further input possibilities: - changes from upper case to lower case and vice versa. - opens the input mask for digits an
d special characters. The function key
changes to . Press , to change again to the letter input mask.˜ - space key for entering spaces. or - moves the character entry cursor (the cursor) in the entry line to the left or right.
- opens a pop-up window with special characters.
AD
AF
AAABACAE
AF
BAT-20H1085
Fig. 3 Input mask for free text input
OKDelete
45
A-Z
A-Z
‚
b
ÄÜ
s36c.b.book Page 8 Thursday, April 9, 2009 2:50 PM

General information
9
- deletes characters in the entry line
starting from the position of the char-
acter entry cursor from right to left. Selecting letters based on specific characters Some letters in the input masks are al
so marked with a small triangle “
a”. This indi-
cates that specific characters base
d on this letter can be selected.
Continue to press down on
the corresponding function key with your finger until a
pop-up window with these specific characte
rs can be displayed. Press to accept the
desired character into the entry line - the po
p-up window will close. If no entries are
entered, the pop-up window will cl
ose automatically after a few seconds.
Input mask for selecting the destination addressWhen entering the destination address,
it is only possible to enter the
characters in the sequence which corresponds to the destinations stored in the navigation system. Limiting the destination an
d selecting from the list
– You can open a list of the selectable destinations any time by pressing
the function key while making
entries in the entry line. Only
destinations selectable from the navigation memory which corre-spond to the requirements and the
character sequence in the entry
line will be displayed.
– The number of selectable destinatio
ns will be displayed in the entry
line if fewer than 99 dest
inations can be selected.
–If fewer than six destinations ar
e selectable, the entry window will
close automatically and a list of possible destinations will be displayed.
Delete
BAT-20H1086
Fig. 4 Input mask for selecting the destination address
List/OK
s36c.b.book Page 9 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
10
Range selector key SETUPTo n e s e t t i n g sBy press ing the button and pres si ng on the functi on key in the
RADIO

mode, you can select the following para
meters using the menu control button :
•
- , ,
and - Volume when switching
on, volume of incoming traffic announce
ments, volume of navigation announce-
ments and speed dependent volume adjustment;•
- Treble setting;
•
- Midtone setting;
•
- Bass setting;
•
- Setting of the volume ratio between the left and right side;
•
- Setting of the volume ratio between the front and the rear;
•
* - Setting the equalizer (linear,
language, rock, cl
assical, dance);
•
* - setting of the surround tone.
GALA function Your radio increases automatically its volu
me with the increasing vehicle speed. A
higher setting value results in a stronger volume increase.
Note
You can set the tone parameters using th
e menu control button or the function
keys or .System settingsPress the button and select the function key .You can select between the following parameters:•
- Menu language for the displa
ys and the language messages;
•
- Keypad display for text entry;
•
* - if your vehicle
is equipped with clim
atronic, the setting
change is displayed when it is activated;•
- Setting the brightness of the screen;
•
- Factory settings;
•
- the information regarding the complete memory capacity of
the SD card and the size of the memory assi
gned to the navigation data is displayed
on the screen;•
- Removing the SD card.
Radio set-upsPress the button in the
RADIO
mode.
Switching the traffic announcements on or off – If you wish to switch the reception of traffic reports on or off, press the
function key .
Determining the station selection via the – By pressing on or , you can select the source
from which the stations are to be selected while in the
RADIO
mode
using the arrow keys. If the is selected, only stored stations from the memory list are called up. The symbol “
ƒ @ „” is
displayed on the screen.
Switching the RDS function on or off (RDS regional) – Press on the function key (regional station) and select a
set-up in the opening pop-up window.
SETUP
To n e
A10
Vo lume
Maximum switch on volume
Traffic announcements (TP)
Navigation volume
Speed dependent vol Adjustment
Tre b l eMidtoneBassBalanceFa d e rEQ SettingsSurround
A10
+
-
SETUP
System
Language
Keypad displayA/C display timeScreenFactory settingsSD card statusRemove SD card
SETUPTraffic information (TP)
Arrow keys
Station list
Memory listMemory listRDS regional
s36c.b.book Page 10 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
11
– Press on the button , doing so always chooses the
frequency for the heard radio statio
n which offers the best reception
at the present time.
– When pressing on the button , the unit attempts to hold a radio
station emitting regionally long en
ough until the reception quality is
so bad, that there is a risk of a program loss.
Delete stored stations – Press the function key and confirm the following safety interroga-
tion in order to delete all radio stations stored in the memory list.
Tra f f i c s t a t i o n s e t - u p sPress the range selector key and then the range selector key
.
Switching the traffic announcements on or off A tick in the check box
7 indicates that the traffic radio function is already switched
on. Dynamic route Opens a pop-up window where it is considered if the TMC traffic reports, received during the route calculat
ion, are to be entered.
Screen set-upsPress the button in the
RADIO
mode and then the function keys
and .
Brightness – Press the function key and select the desired setting for
brightness (5°stages) in a pop-up window.
– A light sensor, which is located in the top right corner of the front
panel, is used for the automati
c correction of the brightness
depending on the light conditions in the vehicle.
Day/Night – Press on the func tion key and s el ec t a setting in the pop-up
window.
– Press the function key if switching the headlights on and off
should also change the map display from night to day design.
– Press on the function key
or to manually determine the
night and day design of the map display.
Confirmation tone – Press on the function key and select a setting in the
pop-up window.
– Press or to switch the tone for confirmation of a function key
operation on the screen on or off.
Media set-upsPress the button in the
MEDIA
mode.
Function keys in the menu°-°Media•
- a tick in the check box
7 means that the function of the
traffic information is switched on.•
- Check box for setting the play function mode Scan,
Mix and Repeat incl. sub-folder (“switched
on”) or without sub-folder (“switched
off”).•
- Setting the volume of the exte
rnal audio source (audio source
AUX is located on the unit).
Automatic
Fix
Delete memoryAllTRAFFIC
SETUP
Traffic information (TP)
˜ Dynamic routeSETUP
System
Screen
Brightness
Day/Night
Automatic
Day
Night
Confirmation tone
On
OffSETUP
Traffic information (TP)Scan/Mix/Repeat incl.

AUX Volume
s36c.b.book Page 11 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
12
•
* - Setting the volume of the external audio source (the audio
source MDI is located under the armrest of the front seats or in a storage compart- ment on the front passenger side).•
* - enables a wireless transfer of MP3 data to the tele-
phone preinstallation. Only operates in
combination with the telephone preinstal-
lation GSM°l - enables the audio play func
tion by means of Bluetooth interface of
portable units (mobile phones) which support the protocol A2DP. Navigation settingsPress the button in the
Navigation
mode.
Function keys in the menu°-°Navigation•
- route options are determined according to the route being
calculated and along which roads the route should lead ,
, and - Route criteria, dynamic
route guidance, route without motorways and route without toll roads/ferries.•
- Setting the volume of th
e navigation announcements.
•
- changes between day and night display, as well as automatic, if the
map display changes automatically accordin
g to the setting of the light switch.
•
- displays a point of interest on the map.
•
- changes the map scale automati
cally depending on the speed and
the driven route (Motorway trip: small map scale - City center: large map scale).•
- during a route guidance, either the arrival or the driving time is
shown in the map display.•
- Enter home address.
•
- you can start a virtual (appare
nt) route guidance in the demo
mode. Virtual route guidance will be repe
ated when reaching the fictive travel
destination. Stop virtual route guidance
normally and deactivate the demo mode
to restart “real” route guidance. As in this case the unit must first reorient itself it can take some time, depending on the number of the currently receiving satellites, until the unit has again found the real location. Drive a short distance.•
- Entering a fictive (inven
ted) starting point in the
demo mode.
•
- Deleting the destination
memory or the list of the
last destinations.•
- Display of information via the data base on CD or SD
card, delete the data base of
the SD card or copy the data.
Route criteria Fa s t
: It calculates the fastest route to your de
stination, even if a detour is necessary.
Short
: Longer driving time in favour of a sh
orter route is acceptable. Please note
that the setting “Short route” during ro
ute guidance can sometimes lead to unex-
pected results. Economical
: The aim of the calculation is a ba
lance between mini
mal driving time
and driving distance. Dynamic route guidance with TMC use If the dynamic navigation is
switched off, traffic reports are nevertheless received in
the background and updated. The navigation displays traffic problems on the map and draws attention to them verbally, ho
wever does not consider them for calcu-
lating the route (the route can le
ad through the traffic problems).
MDI VolumeActivate Bluetooth audio
SETUP
Route options
Route criteria
Dynamic route
Avoid motorways
To l l r o a d / a v o i d
Announcement volumeDay/NightPOIs on mapAutozoomTime displayEnter home addressDemo modeDemo mode starting point
Delete destinations memoryData base navigation
Route criteria
Dynamic route
s36c.b.book Page 12 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
13
Range selector key RADIORadio modeRetrieve radio stationCall up main menu RADIO and choose frequency range – Press the range selector key . The currently heard radio station
is displayed in the middle of the screen
⇒
page 7, fig. 2
.
– Press the range selector key
to change the frequency range.
Alternatively, press on the function key in the main menu RADIO
and select or in the pop-up window.
Changing radio station – By briefly pressing the function ke
ys or , you can change to the
previous or following radio station of the selected frequency band.
– If the symbol “
TP” is displayed on the screen, you can only change
over to the radio stations
with traffic announcements.
– If the symbol “
ƒ @ „” is displayed on the screen, you can only
change over to the stored radio stations.
Selecting a radio station from the station list – If you wish that all the presently receivable radio stations are
displayed, press on the function key and then on the func-tion key . The list “skips” directly to the display of the currently heard radio station.
– Select the desired radio station using the menu control button . Change radio station in the memory list – Press the function key and then the function key and
select the desired radio station using the function keys - .
Manual station finding – If you wish to set the radio statio
n manually using its frequency, press
the function key and then the function key .
– Set the radio station using the menu control button or using the
arrows and on the unit.
BAT-20H1064
Fig. 5 Menu radio: Function key band
BAT-20H1064
Fig. 6 FM station list
RADIO
AA
RADIO
Band
FM
AM
ƒ
„
Freq. Band
FM/List
A10
Extras
Memory1
24
Extras
ManualA10
ƒ
„
s36c.b.book Page 13 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
14
– Briefly press the set button to te
rminate the manual frequency selec-
tion and to display once again the function keys.
Scan function – In order to start the
automatic play
in the current frequency range,
press the function key and then the function key . All radio stations with strong reception are automatically played for approxi-mately five seconds according to the sequence in the station list.
– Press on the function key to end the automatic play of the
currently heard radio station.
Storing a radio stationStoring a radio station – Press the function key and then the function key in
order to open the memory list.
– If you wish to store the displayed radio station in a memory space,
press one of the displayed station keys to and hold it pressed for so long until a signal
sounds. The currently heard radio
station is then stored on this station key.
Deleting a radio station from the memory list – Press the button in the
RADIO
mode and then the function key
.
– Select the radio station you wish to
delete and confirm by pressing the
menu control button .
– If you wish to delete all the stored
radio stations, press on the function
key .
Note
It is alternatively possible to store ra
dio stations by pres
sing the menu control
button .Calling up a radio stationCalling up a station via the station keys – Press the button and then the button and the function
key .
Extras
Scan
Scan
Extras
Memory
1 ...
24 ...
SETUP
Delete memory
A10
All
A10
BAT-20H1063
Fig. 7 Memory list
BAT-20H1075
Fig. 8 Setting the source for selecting the station
RADIO
Extras
Memory
s36c.b.book Page 14 Thursday, April 9, 2009 2:50 PM