2009 Seat Leon 5D COMMUNICATION SYSTEM

Communication
24Speech commands for operating the internal telephone book:Control commands
The control commands are used to carry out functions that
have already been chosen.The control commands are used during or at the end of a dialogue to carry out
certain functions.
Possible commands
Dial number
A telephone number can be vocally specified to the system
and then dialled.– Press the talk button ⇒page 21, fig. 12 . Activation of the
system is confirmed with by a tone.
– After the tone, say the command DIAL NUMBER.After this command the system will then request you to specify a telephone
number. A connection will then be established to the specified number. The
telephone number can be specified all at once, in blocks of digits (separated
by a brief pause), or as single digits. You can specify the digits from zero to
nine . After each block of digits you specify (separated by a brief pause) the
system will repeat the digits. The system can only recognise single digits
(two, three, etc.), and not combinations of digits (e.g. twenty-three).
Speech command
Action
SELECT NAME
After this command, you can call a number that
has been recorded in the phone book under a
name.
STORE NAME
After this command you can store a name with a
telephone number in the phone book
DELETE NAME
After this command you can delete a name from
the phone book.
PLAY PHONE BOOK
After this command you can listen to the names
stored in the phone book
DELETE PHONE BOOK
After this command you can choose to delete the
entire phone book or just a single name
Speech command
Action
DIAL
Telephone number already entered is dialled.
STORE
A name is saved in the phonebook with its phone
number
CANCEL
Cancels a running dialogue.
REPEAT
The specified name or all of the digits specified
up to this point will be repeated. The system will
then give the cue so that you
can specify additional digits or commands.
CORRECTION
The specified name or the last entered block of
digits will be deleted. The system will then give
the cue so that you can specify
additional digits or commands.
ERASE
All specified digits will be deleted. The system
will then give the cue Please, proceed> so that you can specify new dig-
its or commands.AC
Sist Comunicacion_EN.book Seite 24 Mittwoch, 15. Juli 2009 6:45 18

Communication25
Controls and equipmentNotes on specifying telephone numbers:
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.
Example for entering a telephone number:
A running dialogue can be cancelled at any time by pressing the talk button ⇒ page 19, fig. 9 .
Redial– Press the talk button .
– After the tone, say the command REDIAL.After giving the command the last number dialled via the hands-free system
will be dialled again.
Example for the REDIAL command:
A running dialogue can be cancelled at any time by pressing the talk button
⇒ page 20, fig. 10 .To record names in the phone book
You can store names along with a telephone number in the
internal telephone book.– Press the talk button . The beep tone indicates that the system
is ready.
– After the tone, say the command STORE NAME.After giving the command the system will request you to specify a name and
telephone number to store in the internal telephone book. The telephone
Speech command
Condition
Message
Action
DIAL NUMBER
Phone switched
on
please?>
Dialogue
for example,
ZERO, SEVEN,
THREE, ONE
three, one>
Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.No command
mands are: Dial,
repeat, back, or
you can specify
additional digits>
Dialogue
THREE, NINE,
TWO
two>
Dialogue
DIAL
being dialled.>
Dialogue -The tel-
ephone number
0731492 will be
dialledEnd of dialogue
AC
Speech command
Condition
Message
Action
REDIAL
Phone switched
on
being dialled.>
DialogueEnd of dialogue
AC
AC
AC
Sist Comunicacion_EN.book Seite 25 Mittwoch, 15. Juli 2009 6:45 18

Communication
26book has enough memory for 50 names and numbers. You can specify the
digits from zero to nine .
The telephone number can be specified all at once, in blocks of digits (sepa-
rated by a brief pause), or as single digits. After each block of digits you
specify (separated by a brief pause) the system will repeat the digits. The
system can only recognise single digits (two, three, etc.), and not combina-
tions of digits (e.g. twenty-three).
Say STORE to store the entry into the telephone book.
A running dialogue can be cancelled at any time by pressing the talk button ⇒ page 20, fig. 10.
Note
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.•Say the command delete or back to delete or correct the corresponding
block of digits.•Say repeat to have all the digits that have been recognised up to that
point repeated.•If two or more names sound alike, it is better to save the names including
the first name or some other distinguishing entry.•A running dialogue can be cancelled at any time by pressing the talk
button .•The telephone book works only in conjunction with the hands-free speech
control system; the entries are not stored on the phone's SIM card.
Speech command
Condition
Message
Action
STORE NAME
Telephone book
is not full
please?>
Dialogue
COMPANY XYZ
the name>
Dialogue
COMPANY XYZ
please?>
Dialogue
ZERO, ONE, TWO,
THREE
three>
Dialogue
FOUR, FIVE, SIX

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.
No command
mands are: Store,
repeat, back,
delete, or you can
specify addi-
tional digits>
Dialogue
STORE
saved.>
Dialogue - The
name COMPANY
XYZ with the tele-
phone number
0123456 will be
storedEnd of dialogue
AC
AC
Sist Comunicacion_EN.book Seite 26 Mittwoch, 15. Juli 2009 6:45 18

Communication27
Controls and equipment
Calling a name in the phone book– Press the talk button .
– After the tone, say the command SELECT NAMEAfter the system has recognised this command, you may select a stored entry
from the telephone book to call the required number. The system best recog-
nises names spoken by the person who stored the name.
Example for selecting a name from the internal telephone book
A running dialogue can be cancelled at any time by pressing the talk button
⇒ page 20, fig. 10 .
Listening to the phone book
You can have the entries stored in the internal telephone book
read out to you.– Press the talk button ⇒page 20, fig. 10 . The beep tone indi-
cates that the system is ready.
–Say the command PLAY PHONE BOOK.After giving the command the system will read out the entries stored in the
phone book. If you press the talk button as an entry is being read, the
system will call the telephone number for that entry. Once the dialogue is
complete and the system is reactivated, you can also select an entry to call by
specifying the stored name.
Example for the PLAY PHONE BOOK command:
Speech command
Condition
Message
Action
SELECT NAME
Phone is
switched on, tele-
phone book con-
tains entries.
please?>
Dialogue
COMPANY XYZ

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.No command
mands are: dial,
repeat, back>
Dialogue
DIAL
being dialled.>
Dialogue - The
telephone
number for Com-
pany XYZ is being
dialledEnd of dialogue
AC
AC
Speech command
Condition
Message
Action
PLAY PHONE
BOOK
The telephone
book contains
entries.
The telephone
book will then be
read out.End of dialogue
AC
AC
Sist Comunicacion_EN.book Seite 27 Mittwoch, 15. Juli 2009 6:45 18

Communication
28Example for selecting an entry:To erase names from the phone book
You can delete entries from the internal telephone book.– Press the talk button ⇒page 19, fig. 9 . The beep tone indi-
cates that the system is ready.
– After the tone, say the command DELETE NAME.After giving this command you can delete a stored entry from the internal tele-
phone book. Example for deleting single names from the internal telephone book:
A running dialogue can be cancelled at any time by pressing the talk button
⇒ page 19, fig. 9 .
Note
•Say the command Repeat, if you would like to have the specified name
repeated by the system.•If you then say No, the system will answer with and the dialogue
will be ended.
Speech command
Condition
Message
Action
PLAY PHONE
BOOK
The telephone
book contains
entries; the talk
button is
pressed as the
entry is being
read out.
being dialled.>
The selected
name will be
repeated. The tel-
ephone number
will be dialled.End of dialogue
ACAC
Speech command
Condition
Message
Action
DELETE NAME
The telephone
book contains
entries.

Dialogue
COMPANY XYZ
the entry Company
XYZ?>
Dialogue
If no command is specified, the system responds after about 5
seconds with the next cue.
Dialogue
No command
are: yes, no, repeat,
back>
Dialogue
YES

DialogueEnd of dia-
logue
AC
Sist Comunicacion_EN.book Seite 28 Mittwoch, 15. Juli 2009 6:45 18

Communication29
Controls and equipment
To erase the phone book
You can delete the entire phone book or single entries.– Press the talk button ⇒page 19, fig. 9 .
– After the tone, say the command DELETE PHONE BOOK.After giving this command you can delete the entire internal phone book or
single entries as desired.
Example for deleting the entire internal telephone book: Example for deleting single names from the internal telephone book:Speech command
Condition
Message
Action
DELETE PHONE
BOOK
The telephone
book contains
entries.
to delete the
whole phone
book?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no>
Dialogue
YES

Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
AC
No command
mands are: Yes,
no>
Dialogue
YES
is deleted.>
All entries in the
phone book will
be deleted.End of dialogue
Speech command
Condition
Message
Action
DELETE PHONE
BOOK
The telephone
book contains
entries.
to delete the
whole phone
book?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no, repeat>
Dialogue
NO
The telephone
book will then be
read out.
No command
Talk button
pressed as the
entry to be
deleted is read
out.
delete the entry
(name)?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
AC
Sist Comunicacion_EN.book Seite 29 Mittwoch, 15. Juli 2009 6:45 18

Communication
30Notes on the phone book
Take note of these tips and suggestions when using the
phone book.•It is important that names stored in the phone book have a noticeable
acoustic difference between them so the system can recognise the entries.•In the event that an telephone book entry is not recognised (e.g. if
someone else tries to call-up a name), the phone book entries can be read out
by giving the command PLAY PHONE BOOK.•The numbers zero to nine are recognised by the system. Say the numbers
clearly so that the system can recognise them easily.
Should the system say , check the status of the
hands-free system as follows.•Is the phone switched on?•Has the PIN code been entered?
WARNING
The speech system must not be used in cases of emergency, since the voice
changes in stressful situations. This could result in a failed or delayed tele-
phone connection. For this reason, always enter emergency numbers
manually.International calls
Country and area codes can be entered as follows.Notes on entering telephone numbers for calls abroad:•When making a call abroad, you can say plus (+) before specifying the
digits.•After the plus (+) the country code must be specified. The country code
follows the conventional format (e.g. 49 for Germany or 44 for Great Britain.•After the country code, the zero (0) should be left out before the area
code.
Example for making a call to Great Britain:
No command
mands are: Yes,
no>
Dialogue
YES
deleted.>
The entry will be
deleted and the
remaining entries
will be read out.
All entries are
read out.
End of dialogue
Speech command
Condition
Message
Action
DIAL NUMBER
Phone is
switched on.

Dialogue
PLUS, FOUR,
FOUR

Dialogue
SEVEN, THREE,
ONE

Dialogue
Sist Comunicacion_EN.book Seite 30 Mittwoch, 15. Juli 2009 6:45 18

Communication31
Controls and equipment
Bluetooth
®
Bluetooth technology enables wireless connections between
mobile and fixed devices without needing cables.Mobile communication and information is gaining ever greater importance
for personal use as well as in today's modern business world.
Information transfer between mobile devices up until recently was only
possible through wired and infrared connections.
These non-standardised connections greatly limited the range of use and
were very complicated to operate.
For this reason, the introduction of the Bluetooth® technology represents a
great change, allowing the establishment of a standardised remote connec-
tion between mobile devices from different manufacturers.
WARNING
The Bluetooth function must be switched off during air travel (please refer
to the phone manual).
Note
Certain software version of some mobile telephones contain errors or limited
functions (for example “Download phone book”). These errors may give rise
to faulty operation of the vehicle hands-free system. In this case, consult the
Authorised Service Centre for your mobile telephone.Bluetooth
®
Before using the functionality of the Bluetooth connection
between the mobile telephone and the hands-free system for
the first time configuration of the connection is required.It will be necessary that the hands-free system and the mobile telephone
recognise each other. To proceed, first the Bluetooth function on the mobile
telephone must be activated. Then, after switching on the ignition, select the
option on your mobile telephone to search for other Bluetooth communica-
tion devices within range, which will include the hands-free system of the
vehicle (SEAT_BT). The next step is to select this hands-free system. The
complete instructions for completing this operation should be found in the
instruction manual for the telephone.
The final step for establishing the connection is to enter the PIN code for the
hands-free device (initially 1234) . Where the PIN code for the SEAT_BT
system is to be changed, contact any official SEAT dealer. Once the PIN code
is input then the connection is established and the system can be used with
the Bluetooth system. The moment that the connection is established, the
hands-free kit will emit an acute sound.
Once this initial configuration procedure is complete, whenever your mobile
phone and the hands-free device are within range of establishing a Blue-
tooth connection , this is established as long as the ignition is switched on ,
without the need for further configuration.
THREE, NINE,
TWO

Dialogue
DIAL
dialled.>
DialogueEnd of
dialogue
Sist Comunicacion_EN.book Seite 31 Mittwoch, 15. Juli 2009 6:45 18