2009 RENAULT TWINGO RS fuse diagram

13B-67
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$100.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 50, 58
DF032
PRESENT
OR
STOREDTHERMOPLUNGER 1 RELAY CONTROL CIRCUIT
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is present when the ignition is switched on.
See the Technical Note Wiring Diagrams for the vehicle.
For New Twingo
Check the connection and condition of the additional heater 1 relay connector, component code 1067 and the 80 A
maxi fuse in the engine fuse and relay box.
Check the connection and condition of the injection computer connector, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run command AC250 Heating resistor 1 relay.
If the command does not run, check, with the ignition on, for earth on connection 3JA of component 1067.
Check for + 12 V on connection 3FB of component 1067.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
–3JA between components 1067 and 120,
–3FB between components 1067 and 238,
–38LL between components 1067 and 1113,
–BP9 between components 1067 and 597.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, check the relay and replace it if necessary.
If the fault is still present, contact the Techline.
DCM1.2_V50_DF032/DCM1.2_V58_DF032

13B-69
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$100.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 50, 58
DF033
PRESENT
OR
STOREDTHERMOPLUNGER 2 RELAY CONTROL CIRCUIT
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is present when the ignition is switched on.
See the Technical Note Wiring Diagrams for the vehicle.
Check the connection and condition of the additional heater 2 relay connector, component code 1068
and the 80 A maxi fuse in the engine fuse and relay box.
Check the connection and condition of the injection computer connector, component code 120.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run command AC251 Heating resistor 2 relay.
If the command does not run, check, with the ignition on, for earth on connection 3JAA of component 1068.
Check for + 12 V on connection 3FB of component 1068.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
–3JAA between components 1068 and 120,
–3FB between components 1068 and 238,
–38LM between components 1068 and 1113,
–BP9 between components 1068 and 597.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, check the relay and replace it if necessary.
If the fault is still present, contact the Techline.
DCM1.2_V50_DF033/DCM1.2_V58_DF033

13B-70
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$100.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 50, 58
DF034
PRESENT
OR
STOREDTHERMOPLUNGER 3 RELAY CONTROL CIRCUIT
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is present when the ignition is switched on.
See the Technical Note Wiring Diagrams for the vehicle.
Check the connection and condition of the additional heater 2 relay connector, component code 1068
and the 80 A maxi fuse in the engine fuse and relay box.
Check the connection and condition of the injection computer connector, component code 120.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run command AC251 Heating resistor 2 relay.
If the command does not run, check, with the ignition on, for earth on connection 3JAA of component 1068.
Check for + 12 V on connection 3FB of component 1068.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
–3JAA between components 1068 and 120,
–3FB between components 1068 and 238,
–38LM between components 1068 and 1113,
–BP9 between components 1068 and 597.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, check the relay and replace it if necessary.
If the fault is still present, contact the Techline.
DCM1.2_V50_DF034/DCM1.2_V58_DF034