2009 RENAULT TWINGO RS engine oil

13B-240V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP3 The engine starts with difficulty, or starts then stalls
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct: run TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit: run test 5 Air inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR 364
(Mégane II), MR 370 (Scénic II), MR 385
(Modus), MR 392 (Clio III), MR 411
(New Twingo), MR 417 (Kangoo 2),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less
than 2 Ω).
Is the timing set correctly? Carry out the necessary repairs.
Is the compression in order? Carry out the necessary repairs.
Visually check the condition of the engine wiring harness.
YES
NO
NO
YES
NO
YES
A
DCM1.2_V48_ALP3/DCM1.2_V4C_ALP3/DCM1.2_V50_ALP3/DCM1.2_V54_ALP3/DCM1.2_V58_ALP3/DCM1.2_V5C_ALP3

13B-246V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP7 Unexpected acceleration/deceleration and engine racing
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit: run TEST 5 Air inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes.
Visually check the condition of the engine wiring harness.
Check the injectors: run TEST 3 Injector check.
Check the computer:
Check that the computer connectors are properly locked.
Check the condition of the computer connections (bent pin, signs of corrosion, silicone, etc.).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Contact the Techline if the customer complaint is still present.
DCM1.2_V48_ALP7/DCM1.2_V4C_ALP7/DCM1.2_V50_ALP7/DCM1.2_V54_ALP7/DCM1.2_V58_ALP7/DCM1.2_V5C_ALP7

13B-249V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP9 Engine cut-out (stalling)
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct: run TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit: run TEST 5 Air inlet circuit check.
Is the catalytic converter clogged or
damaged?Replace the catalytic converter (see MR 364
(Mégane II), MR 370 (Scénic II), MR 385 (Modus),
MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Visually check the condition of the engine wiring harness.
Check the electrical circuit: run TEST 2 Electrical circuit check.
Check the low pressure circuit: run TEST 1 Low pressure circuit check.
Visually check that there are no leaks on the high pressure circuit: run TEST 7 High pressure circuit
sealing check.
YES
NO
A
DCM1.2_V48_ALP9/DCM1.2_V4C_ALP9/DCM1.2_V50_ALP9/DCM1.2_V54_ALP9/DCM1.2_V58_ALP9/DCM1.2_V5C_ALP9

13B-254V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
* OCR: opening cyclic ratio
ALP11
CONTINUED 1
Is the engine oil level correct? Top up the oil level.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III),
MR 411 (New Twingo), MR 417
(Kangoo 2), 19B, Exhaust, Catalytic
converter: Removal - Refitting).
A
NO
YES
YES
NO
B

13B-256V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
In this case, the control solenoid valve is jammed: the vacuum can increase, but it cannot then be
decreased.
ALP12 Too much power
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes.
Check the air inlet circuit: run TEST 5 Air inlet circuit check.
Check that the engine has not sucked up its oil (engine racing).
Check that the electrical and pneumatic connections of the turbocharger control solenoid valve are correct.
See TEST 10 Turbocharger control solenoid valve check.
Are all the electrical and pneumatic connections of
the turbocharger control solenoid valve correct?Reconnect the hoses and electrical
cables correctly, if necessary.
Are the solenoid valve pipes connected the wrong way
round?Reconnect the pipes correctly.
NO
YES
YES
NO
A
DCM1.2_V48_ALP12/DCM1.2_V4C_ALP12/DCM1.2_V50_ALP12/DCM1.2_V54_ALP12/DCM1.2_V58_ALP12/DCM1.2_V5C_ALP12

13B-258V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
In this case, it may be the solenoid valve dynamic specification which is at fault (atmospheric pressure
resetting time). Final fault finding is carried out by measuring this specification on a special bench.
ALP12
CONTINUED 2
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check that solenoid valve casing does not have any splashes of fluid on it which may impede the breather (water,
engine oil, gearbox oil, brake fluid, coolant, mud, dust, or any other substance).
Instructions:
–The solenoid valve must be set up 450 mm above the ground, in an area free from water, mud, or any other fluid.
–Cleaning with a high pressure jet is forbidden.
Is there coolant present? Follow the recommendations below.
Is the solenoid valve subjected to significant fluctuations
or impacts?
Instructions:
–The solenoid valve must be correctly secured to its
mounting.
Contact with the engine environment is forbidden.Follow the recommendations below.
Check the turbocharger regulation control (no partial jamming, etc.).
Does the turbocharger control work? Carry out the necessary repairs.
Replace the solenoid valve.
If the fault is still present, contact the Techline.
YES
NO
YES
NO
NO
YES

13B-259V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP13 Excessive consumption
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct: run TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Is the fuel temperature sensor leaking? Replace the fuel temperature
sensor, (see MR 364 (Mégane II),
MR 370 (Scénic II), MR 385
(Modus), MR 392 (Clio III), MR 411
(New Twingo), MR 417 (Kangoo 2),
Mechanical, 13B, Diesel injection,
Rail pressure sensor: Removal -
Refitting).
Check the low pressure circuit: run TEST 1 Low pressure circuit check.
Visually check that there are no leaks on the high pressure circuit: run TEST 7 High pressure circuit
sealing check.
Check the air inlet circuit: run TEST 5 Air inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes.
YES
NO
A
DCM1.2_V48_ALP13/DCM1.2_V4C_ALP13/DCM1.2_V50_ALP13/DCM1.2_V54_ALP13/DCM1.2_V58_ALP13/DCM1.2_V5C_ALP13

13B-261V6 MR-413-X44-13B000$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP14Engine races when accelerator is released or when
changing gear
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check that there are no obstacles that might impede the accelerator pedal travel (carpet, point of resistance, etc.).
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes.
Visually check the condition of the engine wiring harness.
Is the clutch clearance set correctly? Carry out the necessary repairs.
Check that the engine has not sucked up its oil (engine racing).
Is the compression in order? Carry out the necessary repairs.
Check that the turbocharger is working properly.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger control solenoid valve
check.
Run TEST 12 Turbocharger.
Is the turbocharger in order?Carry out the necessary repairs.
NO
YES
NO
YES
NO
YES
A
DCM1.2_V48_ALP14/DCM1.2_V4C_ALP14/DCM1.2_V50_ALP14/DCM1.2_V54_ALP14/DCM1.2_V58_ALP14/DCM1.2_V5C_ALP14