2009 RENAULT TWINGO RS gearbox

13B-18V6 MR-413-X44-13B000$040.mif
DIESEL INJECTION
Fault finding – Function13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
Cruise control - speed limiter (CC / SL) management
When activated, the cruise control function maintains the vehicle at a preselected speed, regardless of the
driving conditions encountered. Using the control buttons, the driver can increase or reduce the speed of the vehicle.
The cruise control function can be deactivated either using the control buttons, or by switching off the cruise control
function selector switch or when system events are detected such as the brake or clutch pedal being depressed,
or when system errors are detected such as an inconsistent vehicle speed or excessive vehicle deceleration.
The cruise control function can also be temporarily overridden when the driver wants to resume control of
the vehicle and exceed the selected cruising speed by pressing the accelerator pedal, which causes the controlled
fuel flow to be exceeded. The cruising speed is resumed when the driver releases the accelerator pedal.
It is possible to reactivate cruise control and to return to the last cruising speed after the function has been
deactivated for whatever reason, during the same cycle of use (computer supply voltage not cut off). The vehicle will
then attempt to return to the cruising speed using a controlled vehicle acceleration rate.
When activated (using the selection switch), the vehicle speed limiter function limits the vehicle speed to
a preselected value.
The driver controls the vehicle in the normal way using the accelerator pedal until the limit speed is reached. If an
attempt is made to exceed this speed, the system will ignore the pedal request and will limit the vehicle speed,
provided that the driver continues to depress the accelerator pedal.
As with the cruise control function, the limit speed can be altered using the control buttons by pressing briefly or by
pressing and holding (pressing and holding not active on Kangoo 2).
For safety reasons, the limit speed can be exceeded by depressing the accelerator pedal beyond the pedal position
limit value. The vehicle speed will then be totally controlled by the pedal until the speed falls back below the cruising
speed when the speed limiter function will once again be reactivated.
The driver has the following controls for the cruise control - speed limiter function:
–accelerator pedal,
–brake pedal,
–clutch pedal (not for sequential gearbox),
–function selector switch, used to select cruise control or speed limiter operating mode,
–activation switch on the steering wheel,
–required speed adjustment switch on the steering wheel.

13B-19V6 MR-413-X44-13B000$040.mif
DIESEL INJECTION
Fault finding – Function13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
Instrument panel display
The computer manages the data display on the instrument panel relating to engine operation. This covers five
functions: the OBD warning light for European On Board Diagnostics (EOBD), pre-postheating, coolant temperature,
and Level 1 (non critical fault) and Level 2 (emergency stop) engine faults. These five functions are represented by
five warning lights or messages displayed by the trip computer.
Pre-postheating warning light
This warning light indicates that preheating is active.
Engine coolant temperature warning light
This warning light is used as an engine overheating indicator.
–In the event of overheating, it is up to the driver whether to stop the vehicle or continue driving.
OBD warning light
The OBD fault warning light is used to warn the driver of the presence of injection faults producing excessive
pollution or that the EOBD system is deactivated.
The injection computer requests illumination of the OBD warning light for a present fault only after three consecutive
driving cycles.
The visual check of the warning light when the power is switched on (automatic test procedure managed by
the instrument panel) is carried out by the injection computer. It lasts 3 seconds or until the engine starts for
the New Twingo and Kangoo 2.
If a confirmed OBD fault causes the OBD warning light to come on, there should be no flashing after the warning
light illumination test. The instrument panel will also display the message: Check emission control.
The gearbox computer, if fitted, may also request the illumination of this warning light.
Level 1 warning
If there is a minor fault, the computer may request a level 1 warning to be displayed. Usually, the instrument panel
switches on the SERVICE warning light and sends out a "Check the injection" message. Refer to the operation of the
instrument panel (see 83A, instrument panel). Note:
This warning light comes on only if the vehicle is EOBD approved.
Note:
The SERVICE warning light will come on if the instrument panel is configured as cruise control - speed
limiter present, but the function has not yet been detected by the injection computer.

13B-20V6 MR-413-X44-13B000$040.mif
DIESEL INJECTION
Fault finding – Function13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
Level 2 warning
If there is a major fault, the computer requests a level 2 warning to be displayed. Usually, the instrument panel
switches on the STOP warning light and sends out an "Injection fault" message. Refer to the operation of
the instrument panel (see 83A, instrument panel).
Faults that activate the OBD warning light
* AT: Automatic transmission (automatic gearbox)Tool fault Diagnostic tool title Specification
DF026Cylinder 1 injector control circuitCO - CC
DF027Cylinder 2 injector control circuitCO - CC
DF028Cylinder 3 injector control circuitCO - CC
DF029Cylinder 4 injector control circuitCO - CC
DF648Computer1.DEF - 2.DEF
DF114EGR solenoid valve circuit
(EGR valve jammed open)4.DEF
DF209EGR valve position sensor circuit
(Minimum and maximum positions)CO - CC.1
DF099*AT* or sequential gearbox connection via the multiplex network*1.DEF
DF016EGR control circuitCO – CC.1 – CC.0

13B-28V6 MR-413-X44-13B000$080.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
*supply: supplyDF0530089 Rail pressure regulation function
DF0560100 Air flow sensor circuit
DF0572264 Water in diesel fuel detector circuit
DF0590263 Misfires in cylinder 1
DF0600266 Misfires in cylinder 2
DF0610269 Misfires in cylinder 3
DF0620272 Misfires in cylinder 4
DF0890235 Inlet manifold pressure sensor circuit
DF0980180 Fuel temperature sensor circuit
DF099C101Automatic or sequential gearbox connection via the multiplex
network
DF1070604 Computer memory
DF1120340 Cylinder reference sensor circuit
DF1130641 Sensor feed voltage
DF1140400 EGR solenoid valve circuit
DF1210325 Accelerometer circuit
DF1220651 Pedal potentiometer gang 2 supply voltage
DF1300087 Flow capacity function
DF1950016 Camshaft sensor / engine speed consistency
DF2090487 EGR valve position sensor circuit
DF2210830 Clutch switch signal
DF2420654 Engine speed signal output
DF2610045 Turbocharger actuator circuit
DF4272263 Turbocharger actuator control
DF4890645 Air conditioning compressor control
DF6310703 Brake light switch signal
DF648062F Computer
DF8590170 Injector programming cycle not done
DF8862269 Presence of water in the diesel fuel
DF10700534 Cold loop
Tool faultDTC codeDiagnostic tool title

13B-37
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF008
PRESENT
OR STOREDPEDAL POTENTIOMETER CIRCUIT GANGED CIRCUIT 1CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 volts
1.DEF: Inconsistency between pedal gangs 1 and 2
2.DEF: No signal
3.DEF: Jammed component
NOTESPriority for dealing with a combination of faults:
–DF113 Sensor supply voltage.
Special note:
If fault DF008 is present: the idle speed is fast (1000 rpm), the engine performance is
reduced to 75%, and the level 1 warning light illuminates with the message Check
injection displayed on the instrument panel.
If DF008 and DF009 Pedal potentiometer circuit gang 2 are present: the engine
speed increases to 1300 rpm or 1700 rpm if the vehicle is fitted with a sequential
gearbox (fault on gangs 1 and 2), and the level 1 warning light illuminates with
the message Check injection displayed on the instrument panel.
Note: possible risk of the engine speed racing with no load for 1 second.
See the Technical Note Wiring Diagrams for the vehicle.
1.DEF
3.DEF
NOTESNone.
Disconnect connector A (black) of the injection computer, component code 120 and the connector of the pedal
potentiometer, component code 921.
Check the insulation between connections 3LS and 3LW of component 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the accelerator pedal potentiometer, component code 921 (see MR 364
(Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2),
Mechanical, 13B, Diesel injection, Accelerator pedal potentiometer: Removal - Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF008/DCM1.2_V4C_DF008/DCM1.2_V50_DF008/DCM1.2_V54_DF008/DCM1.2_V58_DF008/DCM1.2_V5C_DF008

13B-40
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF009
PRESENT
OR STOREDPEDAL POTENTIOMETER TRACK 2 CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 volts
NOTESPriority for dealing with a combination of faults:
–DF122 Pedal potentiometer gang 2 supply voltage.
Special note:
If fault DF009 is present: the idle speed is fast (1000 rpm), the engine performance is
reduced to 75%, and the level 1 warning light illuminates with the message Check
injector displayed on the instrument panel.
If DF009 and DF008 Pedal potentiometer circuit gang 1 are present: the engine
speed increases to 1300 rpm or 1700 rpm if the vehicle is fitted with a sequential
gearbox (fault on gangs 1 and 2), and the level 1 warning light illuminates with
the message Check injection displayed on the instrument panel.
Note: possible risk of the engine speed racing with no load for 1 second.
See the Technical Note Wiring Diagrams for the vehicle.
CO.0
NOTESSpecial note:
None.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of connector A (black 32-track) of the computer, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + 5 V on connection 3LU of component 921.
Check for earth on connection 3LV of component 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Disconnect connector A of the computer, component code 120 and the connector of the pedal potentiometer,
component code 921.
Check the insulation against earth of connection 3LW on component 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
DCM1.2_V48_DF009/DCM1.2_V4C_DF009/DCM1.2_V50_DF009/DCM1.2_V54_DF009/DCM1.2_V58_DF009/DCM1.2_V5C_DF009

13B-97
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50
DF099
PRESENT
OR
STOREDAUTOMATIC TRANSMISSION OR SEQUENTIAL GEARBOX
CONNECTION VIA THE MULTIPLEX NETWORK
1.DEF: No signal
NOTESSpecial notes:
–Gearbox does not change gear in automatic mode.
–OBD warning light illuminated.
See Technical Note Wiring Diagrams of the vehicle concerned.
Run a multiplex network test (see 88B, Multiplex).
Check the connection and condition of connector A (black 52-track) of the sequential gearbox computer,
component code 119.
Check the connection and condition of connector C (brown 48-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, the continuity and the absence of interference resistance on the following connections:
–3MT between components 119 and 120,
–3MS between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
DCM1.2_V48_DF099/DCM1.2_V4C_DF099/DCM1.2_V50_DF099

13B-114
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50
DF242
PRESENT OR
STOREDENGINE SPEED SIGNAL OUTPUTCC.1: Short circuit to + 12 volts
CO.0: Open circuit or short circuit to earth
NOTESSpecial note:
The operation of the power-assisted steering is not correct.
See Technical Note Wiring Diagrams of the vehicle concerned
Check the connection and condition of the variable power-assisted steering connector, component code 502.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connection:
–H7 between components 120 and 502.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, run fault finding on the power-assisted steering and the sequential gearbox (see 36B,
Power-assisted steering) and (see 21B, Sequential gearbox).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF242/DCM1.2_V4C_DF242/DCM1.2_V50_DF242