2009 RENAULT TWINGO RS display

86D-16V1 MR-413-X44-86D000$070.mif
86D
BIC
Vdiag No.: 14
For information on removing and refitting the multimedia connection unit of the multimedia network, refer to the
repair manual for the vehicle concerned:
If the vehicle is equipped with a Navigation computer (Only on Clio III):
See MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting.
If the vehicle is not equipped with a Navigation computer:
Clio III: See MR 392, Mechanical, 86A, Radio, Display: Removal - Refitting.
New Twingo: See MR 411, Mechanical, 86A, Radio, Display: Removal - Refitting.
Operations to be carried out before replacing the multimedia network interface unit:
1- Before replacing the multimedia connection unit (with Techline approval), read the faults and carry out a
conformity check to check that it is actually defective.
2-After obtaining Techline approval, remove the multimedia connection unit, with the ignition off (wait 1 minute for
the system to shut down completely).
The multimedia network interface units available from the Parts Department are supplied unconfigured.
Operations to be carried out after replacing the multimedia connection unit:
–Connect the diagnostic tool and switch on the system, then establish dialogue with the computer.
–Configure the multimedia connection unit (see Configurations and Programming).
–Configure the computer using command CF007 Vehicle configuration, then perform CF012 Lighting. Only carry
out these configurations on vehicles not equipped with a Navigation system. (see Configurations).
–If a radio is present, configure the computer using command CF008 Radio (see Configurations).
–If a Navigation system is present, configure the computer using command CF009 Navigation (see
Configurations).
–Enter the VIN code using command VP001 Write VIN (see Programming).
–Check that there are no faults and that the multimedia system is operating correctly. Note:
If the radio and the multimedia connection unit (BIC) are replaced simultaneously, the multimedia
connection unit must be configured first (see Configurations and Programming).
MULTIMEDIA CONNECTION UNIT
Fault finding – Replacement of components

86D-19
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF002
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact your Techline.
BIC_V14_DF002

86D-20
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF003
PRESENT
OR
STOREDSCREEN
DEF: No communication with display
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
If the fault is present, the display does not operate.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault persists, contact your Techline.
BIC_V14_DF003

86D-21
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF005
PRESENT
OR
STOREDSUPPLY
1.DEF: Excess voltage
2.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
Special notes:
The undervoltage fault appears if the computer feed voltage is less than or equal to
7.5 V for at least 1 second.
The overvoltage fault appears if the computer feed voltage is greater than or equal to
18.5 V for at least 1 second.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
1.DEF
NOTESNone.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
BIC_V14_DF005

86D-22
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF005
CONTINUED
2.DEFNOTESNone.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the condition of fuse F48 (15 A) for New Twingo or fuses F14 (5 A), F2 (20 A), and unit fuse 710 (15 A) for
Clio III.
Check the connection and condition of the connectors of the display computer, component code 653 or of the
multimedia connection unit computer, component code 1714, depending on the vehicle equipment.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the computer connector and check the conformity of the following connections:
–BCP4 between components 260 and 653 or 1714,
–BPT between components 645 and 653 or 1714,
–BPT3 between components 260 and 653 or 1714,
–NAM between component 653 or 1714 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.

86D-23
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF006
PRESENT
OR
STOREDACTIVATION SIGNAL
CO : Open circuit
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
NOTESFault finding procedure application conditions:
The fault is declared present after:
The + after ignition feed is activated, then the multimedia system was switched on using
the on/off button.
The fault is declared stored after the vehicle is completely shut off (1 minute after
locking).
If the fault is present, the multimedia functions do not operate.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation system:
Check the connectors of the multimedia connection unit, component code 1714, of the radio, component
code 261, of the mobile connectivity computer, component code 1959 (depending on equipment), and of the
navigation computer, component code 662.
For a vehicle not equipped with a Navigation system:
Check the connectors of the display, component code 653, of the radio, component code 261, and of the mobile
connectivity computer, component code 1959 (depending on equipment).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
BIC_V14_DF006

86D-25
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF007
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESIf the fault is present, the multimedia function is locked and no computer (radio, radio
control satellite, etc.) operates.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact your Techline.
BIC_V14_DF007

86D-26
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF008
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESIf the fault is present, the multimedia function is locked and no computer (radio, radio
control satellite, etc.) operates.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault persists, contact your Techline.
BIC_V14_DF008