2009 RENAULT TWINGO RS steering

84A-2
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Set the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .aRemove the lower cover bolts (1) .
aUnclip the upper cover at (2) .
aRemove the upper cover (3) . Equipment required
Diagnostic tool
WARNING
To prevent damaging the rotar y switch, do not turn
the mobile section of the rotary switch.
WARNING
Incorrect wheel alignment could ruin the rotary
switch.
ENGINE REV COUNTER
127437
127438

84A-3
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
aRemove the lower cover (4) .
aRemove:
-the driver's side front airbag (see 88C, Air bag and
Pretensioners, Driver's frontal airbag: Removal
- Refitting, page 88C-6) ,
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering),II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLock the driver's front airbag (5) connector in the
housing of the radio satellite connector to immobilise
the rotary switch throughout the removal operation.
127439
127766

84A-4
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
aDisconnect the steering column switch assembly
connectors.
aRemove the bolt (6) from the steering column switch
assembly.
aUse a flat-blade screwdriver at (7) to release the
steering column switch assembly.
aRemove the steering column switch assembly from
the steering column.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a
Ensure that the wheels are set straight ahead.a
aRefit the steering column switch assembly to the
steering column.
aConnect the various steering column switch assem-
bly connectors.
127769
WARNING
Incorrect wheel alignment could ruin the rotary
switch.
127767
Note:
Always keep the rotary switch immobilised in (8)
throughout the refitting operation.

84A-5
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
aCheck that the rotary switch is positioned correctly:
the outlet for the driver's front airbag (9) wiring
always must be facing upwards.
aAt the last moment, remove the immobilised (10)
connector.
II - FINAL OPERATION.
aRefit:
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering),
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6) .
-the cowlings under the steering wheel.
aRefit the rev counter (see 83A, Instrument panel,
Rev counter: Removal - Refitting, page 83A-3) .
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners).
aSwitch on the ignition.
aCheck the operation of the rotary switch:
-turn the steering wheel to the left until it stops,-turn the steering wheel to the right until it stops,
-check that there are no faults on the instrument pa-
nel.
127766
ENGINE REV COUNTER

84A-7
CONTROL - SIGNALS
Screen wiper switch: Removal - Refitting
84A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (5) .
aRemove the windscreen wiper switch by pressing
down on the clips (6) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the wiper switch connector.
aClip the windscreen wiper switch onto the rotary
switch.
II - FINAL OPERATION.
aRefit:
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) ,
-the cowlings under the steering wheel.
aRefit the rev counter (see 83A, Instrument panel,
Rev counter: Removal - Refitting, page 83A-3) .
127765
ENGINE REV COUNTER

84A-9
CONTROL - SIGNALS
Signals and lighting switch: Removal - Refitting
84A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (5) .
aRemove the signal lighting switch by pressing on the
clips (6) .
REMOVAL
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the signalling light switch connector.
aClip the indicator light switch onto the rotary switch.
II - FINAL OPERATION.
aRefit the covers under the steering wheel.
aRefit the rev counter (see 83A, Instrument panel,
Rev counter: Removal - Refitting, page 83A-3) .
121133
ENGINE REV COUNTER

84A-12
CONTROL - SIGNALS
Lighting dimmer: Removal - Refitting
C44 or G44
84A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aUnclip the storage compartment (1) under the stee-
ring wheel.
aUnclip the trim under the steering wheel (2) .
aDisconnect the various connectors from the plate.
aRemove the trim under the steering wheel.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the lighting dimmer by pressing on the clips
(3) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip the lighting dimmer onto the trim under the stee-
ring wheel.
II - FINAL OPERATION.
aConnect the various connectors.
aRefit:
-the trim under the steering wheel,
-the storage compartment.
119506
120279
119495

86A-12
RADIO
Radio control satellite: Removal - Refitting
WITH 4 SPEAKERS, WITHOUT RADIO or RADIO NO. 01 or RADIO NO. 03
86A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (5) from the radio control
satellite.
aRemove:
-the bolt (6) from the radio control satellite,
-the radio control satellite (7) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the radio control satellite on the steering colu-
mn switches.
aConnect the radio control satellite connector.
II - FINAL OPERATION.
aRefit:
-the lower cover,
-the upper cover.
aRefit the rev counter (see 83A, Instrument panel,
Rev counter: Removal - Refitting, page 83A-3) .
121134
ENGINE REV COUNTER