2009 RENAULT TWINGO RS fuel

17B-327V7 MR-413-X44-17B000$180.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
CLEAR:
ACTIVATION:Tool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used for clearing the stored faults from the
computer.
RZ005 programmingThis command enables you to reinitialise the entire vehicle
configuration.
Tool
commandDiagnostic tool title Comments
AC015 Fuel pump relayThis commands enables the fuel pump to be listened to.
AC017Canister bleed solenoid
valveThis command enables the canister bleed solenoid valve to be
opened.
AC027 Motorised throttleThis command enables the motorised throttle to be opened.
AC038Low speed fan assembly
relayThis command enables the fan unit relay to be controlled.
AC039High speed fan assembly
relayThis command enables the fan unit relay to be controlled.
AC079 Actuator static testThis activation enables several actuators to be controlled.
AC117Upstream O2 sensor
heatingThis command enables the upstream sensor heating to be
controlled.
AC118Downstream O2 sensor
heatingThis command enables the downstream sensor heating to be
controlled.
AC156Camshaft dephaser 1
(only for CLIO III or MODUS)This activation enables the camshaft dephaser to be controlled.
AC180Air conditioning
compressor relay controlThis command enables the air conditioning compressor relay to
be controlled.
AC199Controlled coolant
thermostat
(only for Vdiag 4C)The activation of this command enables the controlled coolant
thermostat to be opened.
AC253Camshaft dephaser:
Normal controlThis activation enables the camshaft dephaser solenoid valve to
be fully controlled in a repetitive manner with the ignition on.
AC254Camshaft dephaser:
On/off controlThis activation enables the camshaft to be completely shifted in
relation to the pulley with the engine idling.
PETROL INJECTION
Fault finding – Command summary table

17B-329V7 MR-413-X44-17B000$190.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC015FUEL PUMP RELAY
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
IF THE RELAY DOES NOT CLICK 10 TIMES
Check the condition of the fuel pump relay connector (see NEW TWINGO or E33, component code 236).
Check the condition of the engine management computer connector (component code 120).
Check the condition of the Protection and Switching Unit connector (CLIO III or MODUS, component code 1337).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise change the wiring.
Use the universal bornier to check the insulation and continuity of the following connections:
●3AC between components 120 and 236 (for NEW TWINGO or E33),
●3AC between components 120 and 1337 (for CLIO III or MODUS).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, there is a fault in the Protection and Switching Unit (the fuel pump relay is in the Protection
and Switching Unit and is not removable) (for CLIO III or MODUS).
Perform fault finding on the UCH (see 87B, Passenger compartment connection unit) (for NEW TWINGO or
E33) or the Protection and Switching Unit (see 87G, Engine compartment connection unit) (for CLIO III
or MODUS).
If the fault is still present, contact the Techline.
SIM32_V44_AC015 / SIM32_V4C_AC015 / SIM32_V50_AC015 / SIM32_V54_AC015
PETROL INJECTION
Fault finding – Interpretation of commands
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-330V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC015
CONTINUED 1
IF THE PUMP DOES NOT OPERATE
Check the condition of the fuel pump connector (component code 833).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
With the ignition on, check for + 12 V on connection 3N on the fuel pump, component code 833.
Run command AC015:
If there is no + 12 V:
–disconnect the battery,
–disconnect the connector in the Protection and Switching Unit (for CLIO III or MODUS),
–Check the condition of the Protection and Switching Unit (see Wiring Diagrams Technical Note, CLIO III or
MODUS, component code 1337).
–Check the condition and connections of the UCH (see 87B, Passenger compartment connection unit)
(for NEW TWINGO or E33).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Use the universal bornier to check the insulation and continuity of the following connections:
●3N between components 833 and 236 (for NEW TWINGO or E33),
●3N between components 833 and 1337 (for CLIO III or MODUS).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-331V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC015
CONTINUED 2
For CLIO III or MODUS:
Reconnect the Protection and Switching Unit connector and reconnect the battery.
If there is still no + 12 V on the fuel pump relay connector, there is a fault in the Protection and Switching Unit.
Carry out fault finding on the Protection and Switching Unit (see 87G, Engine compartment connection unit).
If the fault is still present, contact the Techline.
For NEW TWINGO or E33:
Reconnect the battery.
With the ignition on, if the + 12 V is still not present on the fuel pump relay connector, there is a fault in the engine
fuse and relay box.
Carry out fault finding on the engine fuse and relay box to check the 30A fuse and the continuity of the following
connection:
●BP17 between components 120 and 397, 238 and 397.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, check the battery and run fault finding on the charging circuit (see Technical Note 6014A,
Checking the charging circuit).
IF THE PUMP DOES NOT OPERATE
Check that there is an earth on connection MF on the fuel pump, component code 833.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the fuel pump.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-332V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC017CANISTER BLEED SOLENOID VALVE
NOTESThere must be no present or stored faults.
During activation of this command, the fuel vapour absorber bleed solenoid valve
should be operated 10 times.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Check the condition of the fuel vapour absorber bleed solenoid valve connector (component code 371).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the fuel vapour absorber bleed solenoid valve between connections 3FB and 3BB.
If the resistance is not between:
22 Ω < X < 30 Ω, at 23˚C, replace the canister bleed solenoid valve.
With the ignition on, check for + 12 V on connection 3FB of the fuel vapour absorber bleed solenoid valve
connector, component code 371.
If there is no + 12 V:
–Disconnect the battery.
–Disconnect the injection locking relay connector, component code 238 (for NEW TWINGO or E33).
–Check the condition of the injection locking relay connector (see Wiring Diagrams Technical Note for
NEW TWINGO or E33, component code 238).
–Check the condition of the Protection and Switching Unit (see Wiring Diagram Technical Note, CLIO III or
MODUS, component code 1337).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Use the "universal bornier" to check the continuity of the following connections:
●3FB between components 371 and 238 (for NEW TWINGO or E33),
●3FB between components 371 and 1337 (for CLIO III or MODUS).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
SIM32_V44_AC017 / SIM32_V4C_AC017 / SIM32_V50_AC017 / SIM32_V54_AC017
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-333V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC017
CONTINUED
For CLIO III or MODUS:
Reconnect the Protection and Switching Unit connector and reconnect the battery.
If, with the ignition on, there is still no + 12 V on the fuel vapour absorber
canister bleed solenoid valve connector, there is a fault in the Protection and Switching Unit.
Carry out fault finding on the UPC (see 87G, Engine compartment connection unit).
If the fault is still present, contact the Techline.
For NEW TWINGO or E33:
Reconnect the injection locking relay connector and reconnect the battery.
With the ignition on, if there is still not + 12V on the connector for the fuel vapour absorber bleed solenoid, there is
a fault in the engine fuse and relay box.
Carry out fault finding on the engine fuse and relay box, by checking the continuity of the following connection:
●BP17 between components 120 and 397, 238 and 397.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, check the battery and run fault finding on the charging circuit (see Technical Note 6014A,
Checking the charging circuit).
Disconnect the battery.
Check the condition of the engine management computer connector (see Wiring Diagrams Technical Note for
NEW TWINGO, E33, CLIO III, or MODUS, component code 120).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Use the universal bornier to check the insulation and continuity of the following connection:
●3BB between components 120 and 371.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for earth on connection 3BB of the fuel vapour absorber bleed solenoid valve when running command
AC017 Canister bleed solenoid valve.
Replace the fuel vapour absorber bleed solenoid valve.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-343V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP2 The engine will not start
NOTESApply ALP2 after a complete check using the diagnostic tool.
If the starter motor does not operate, there may be a fault with the engine immobiliser. Check status ET341
Immobiliser code programmed, if YES apply the following procedure, if NO, run command SC017 Programming
injection immobiliser code, in the UCH in repair mode (see 17B, Petrol injection, Replacement of
components).
In the event of a fault, perform fault finding on the UCH (see 87B, Passenger compartment connection unit).
Check the condition of the battery.
Check the cleanliness, condition and tightness of the battery terminals.
Check that the battery is correctly earthed to the vehicle bodywork.
Check that the + battery leads are correctly connected.
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Check that the starter motor is properly connected.
Check that the starter operates correctly.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that there is fuel in the tank (fuel sender fault).
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check the sealing of the injectors, and that they are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP02 / SIM32_V4C_ALP02 / SIM32_V50_ALP02 / SIM32_V54_ALP02
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-344V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP3 Idle speed faults
NOTESApply ALP3 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the inlet system sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery circuit (manifold - cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Measure the electrical resistance of the quadruple ignition module.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP03 / SIM32_V4C_ALP03 / SIM32_V50_ALP03 / SIM32_V54_ALP03
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.