2009 RENAULT TWINGO RS fuel pressure

17B-144V7 MR-413-X44-17B000$133.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
DF398
PRESENT
OR
STOREDFUEL CIRCUIT OPERATING FAULT1.DEF: Operational fault finding on the fuel circuit should detect a fault on the petrol
system causing the EOBD pollutant emission thresholds to be exceeded.
The on-board diagnostic can detect:
–clogging of the injectors or an injector flow fault,
–a fault in the supply system (pressure regulator, fuel pump, filter, etc.),
–a poor connection in the petrol or injection circuits.
2.DEF: EOBD
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running (wait for approximately
2 minutes).
Check:
–the fuel pressure,
–the fuel filter,
–the fuel pipes,
–clogging of the injectors or an injector flow fault (see MR 392 (Clio III), MR 385 (Modus), MR 411
(New Twingo), or MR 442 (E33), Mechanical, 13A, Fuel supply).
If the fault is still present, contact the Techline.
SIM32_V44_DF398/SIM32_V4C_DF398/SIM32_V50_DF398/SIM32_V54_DF398
AFTER REPAIREnsure that all the faults have been dealt with.
Clear the stored faults. Do not clear the programming.
To check that the system has been properly repaired:
–there must be no further electrical faults,
–programming has been carried out,
the engine must be warm (minimum 75˚C), and idling, with all electrical consumers
running for 15 minutes.

17B-170V7 MR-413-X44-17B000$150.mif
PETROL INJECTION
Fault finding – Status summary table17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
Tool statusDiagnostic tool title
ET358High-speed fan unit relay connection
ET405Clutch pedal switch
ET415Deactivation of cruise control/speed limiter
ET556Driver deactivation of the cruise control/speed limiter
ET557Cruise control/speed limiter deactivation by function
ET561Operating mode (Only for Ethanol or E85 vehicle)
ET562Fan assembly request from automatic transmission (except D7F800)
ET564Type 1 defect mode
ET565Type 2 defect mode
ET566Type 3 defect mode
ET567Type 4 defect mode
ET568Type 5 defect mode
ET569Defect mode type 6
ET578Petrol fuel circuit fault finding
ET603Air conditioning compressor relay control circuit
ET671Alcohol level programming (Only for Ethanol or E85 vehicle)
ET672Engine coolant temperature management (Only for Vdiag 4C)
ET673Jammed accelerator pedal detected
ET674Refrigerant pressure
ET703Cruise control/speed limiter buttons
ET704Brakecontact No 1
ET705Brakecontact No 2
ET840 Customised Oil Change Interval (except Vdiag 44 and 4C)

17B-196V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET054
CONTINUED
IDLING SPEED TOO LOW
Check:
–engine oil level (too high, splashing),
–that the exhaust pipe is not blocked (catalytic converter damaged),
–the cleanliness and conformity of the air filter,
–that the air inlet circuit is not blocked,
–that the throttle valve assembly is not clogged,
–the condition and conformity of the spark plugs,
–the fuel circuit sealing,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing setting.
Repair or replace the faulty components, if necessary.
IDLING SPEED TOO HIGH
Check:
–engine oil level (too high, splashing),
–for the fittings in the oil vapour rebreathing system,
–the sealing between the throttle valve and inlet manifold,
–the manifold pressure sensor sealing,
–the fuel vapour absorber bleed, which must not be jammed open,
–the fuel vapour absorber bleed system sealing,
–the brake servo system sealing,
–the sealing between the inlet manifold and cylinder head,
–the oil vapour recovery circuit sealing between the inlet manifold and cylinder head,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing adjustment,
Repair or replace the faulty components, if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-263V7 MR-413-X44-17B000$160.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* OCR: Opening cyclic ratio
* EV: Solenoid valve
* mot: motorised
* app.: applying
* AAC: Camshaft
Tool ParameterDiagnostic tool title
PR014Idling speed correction
PR015Engine torque
PR018Estimated air flow
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure
PR041Turbocharger pressure (Vdiag 54 only)
PR055Engine speed
PR059Inlet air temperature
PR064Coolant temperature
PR071Computer feed voltage
PR089Vehicle speed
PR090Idle speed regulation programming value
PR091OCR* Theoretical idle speed regulation
PR094AAC* dephaser OCR* setpoint (Vdiag 4C only)
PR095Anti-pinking correction
PR096Mot.* throttle upper stop programmed value.
PR097Mot.* throttle lower stop programmed value.
PR098Upstream oxygen sensor voltage
PR099Downstream oxygen sensor voltage
PR101Duration of injection
PR102Canister bleed solenoid valve OCR*
PR103Instantaneous fuel consumption
PR104Turbocharging EV* OCR* (Vdiag 54 only)
PR105Mileometer OBD fault warning light lit
PR106Mileometer fault warning light lit
PR111Motorised throttle position corrected value.
PR113Lower throttle stop after app.* offset
PR116Motorised throttle corrected position setpoint
PR118Measured throttle position gang 1
PR119Measured throttle position gang 2
PETROL INJECTION
Fault finding – Parameter summary table

17B-343V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP2 The engine will not start
NOTESApply ALP2 after a complete check using the diagnostic tool.
If the starter motor does not operate, there may be a fault with the engine immobiliser. Check status ET341
Immobiliser code programmed, if YES apply the following procedure, if NO, run command SC017 Programming
injection immobiliser code, in the UCH in repair mode (see 17B, Petrol injection, Replacement of
components).
In the event of a fault, perform fault finding on the UCH (see 87B, Passenger compartment connection unit).
Check the condition of the battery.
Check the cleanliness, condition and tightness of the battery terminals.
Check that the battery is correctly earthed to the vehicle bodywork.
Check that the + battery leads are correctly connected.
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Check that the starter motor is properly connected.
Check that the starter operates correctly.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that there is fuel in the tank (fuel sender fault).
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check the sealing of the injectors, and that they are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP02 / SIM32_V4C_ALP02 / SIM32_V50_ALP02 / SIM32_V54_ALP02
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-344V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP3 Idle speed faults
NOTESApply ALP3 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the inlet system sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery circuit (manifold - cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Measure the electrical resistance of the quadruple ignition module.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP03 / SIM32_V4C_ALP03 / SIM32_V50_ALP03 / SIM32_V54_ALP03
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-345V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP4 Faults occurring while driving
NOTESApply ALP4 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Check inlet line sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery system (manifold/cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP04 / SIM32_V4C_ALP04 / SIM32_V50_ALP04 / SIM32_V54_ALP04
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-347V7 MR-413-X44-17B000$220.mif
PETROL INJECTION
Fault finding – Tests17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
TEST 1 Petrol conformity check
WARNING
During this operation, it is essential to:
–refrain from smoking or bringing incandescent objects close to the work area,
–protect yourself against fuel splashes due to residual pressure in the pipes,
–wear safety goggles with side guards,
–wear leaktight gloves (Nitrile type).
IMPORTANT
–To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
–To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Remove 1 l of fuel at the fuel filter outlet, in the engine compartment (see MR 385 (Modus), MR 392 (Clio III),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 19C, Tank, Fuel tank: Draining), using a pneumatic
transfer pump (part no. 634-200) and place it in 1300 ml plastic cup (part no. 77 11 171 413).
Close the plastic cup with its cover (part no. 77 11 171 416) and let the fuel rest for approximately 2 minutes.
This type of plastic cup is used to prepare paint.
Is the fuel cloudy or does it
separate into two parts?Water is present in the petrol; the fuel is not correct.
Drain the fuel circuit, including the tank (see MR 385 (Modus),
MR 392 (Clio III), MR 411 (New Twingo), or MR 442 (E33),
Mechanical, 19C Tank, Fuel tank: Draining).
Visually compare the fuel removed with the correct petrol.
Are the samples identical?
YES
NO
YES
A
NO
B
SIM32_V44_TEST1/SIM32_V4C_TEST1/SIM32_V50_TEST1/SIM32_V54_TEST1