17B-170V7 MR-413-X44-17B000$150.mif
PETROL INJECTION
Fault finding – Status summary table17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
Tool statusDiagnostic tool title
ET358High-speed fan unit relay connection
ET405Clutch pedal switch
ET415Deactivation of cruise control/speed limiter
ET556Driver deactivation of the cruise control/speed limiter
ET557Cruise control/speed limiter deactivation by function
ET561Operating mode (Only for Ethanol or E85 vehicle)
ET562Fan assembly request from automatic transmission (except D7F800)
ET564Type 1 defect mode
ET565Type 2 defect mode
ET566Type 3 defect mode
ET567Type 4 defect mode
ET568Type 5 defect mode
ET569Defect mode type 6
ET578Petrol fuel circuit fault finding
ET603Air conditioning compressor relay control circuit
ET671Alcohol level programming (Only for Ethanol or E85 vehicle)
ET672Engine coolant temperature management (Only for Vdiag 4C)
ET673Jammed accelerator pedal detected
ET674Refrigerant pressure
ET703Cruise control/speed limiter buttons
ET704Brakecontact No 1
ET705Brakecontact No 2
ET840 Customised Oil Change Interval (except Vdiag 44 and 4C)
17B-196V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET054
CONTINUED
IDLING SPEED TOO LOW
Check:
–engine oil level (too high, splashing),
–that the exhaust pipe is not blocked (catalytic converter damaged),
–the cleanliness and conformity of the air filter,
–that the air inlet circuit is not blocked,
–that the throttle valve assembly is not clogged,
–the condition and conformity of the spark plugs,
–the fuel circuit sealing,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing setting.
Repair or replace the faulty components, if necessary.
IDLING SPEED TOO HIGH
Check:
–engine oil level (too high, splashing),
–for the fittings in the oil vapour rebreathing system,
–the sealing between the throttle valve and inlet manifold,
–the manifold pressure sensor sealing,
–the fuel vapour absorber bleed, which must not be jammed open,
–the fuel vapour absorber bleed system sealing,
–the brake servo system sealing,
–the sealing between the inlet manifold and cylinder head,
–the oil vapour recovery circuit sealing between the inlet manifold and cylinder head,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing adjustment,
Repair or replace the faulty components, if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
17B-274V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR041
CONTINUED
–Check the cleanliness of the air filter.
–Replace the filter if necessary.
–Check that the air inlet circuit is not blocked.
The turbocharging system must be perfectly sealed, from the exhaust manifold to the turbocharger, from the
turbocharger to the heat exchanger and from the heat exchanger to the throttle valve.
Check that there are no air leaks:
–around the turbocharger pressure sensor,
–around the air temperature sensor.
Check absence of leaks in the wastegate capsule pressure circuit connected to the turbocharger system.
Check that the air-air heat exchanger is not clogged (presence of oil).
If there is oil in the heat exchanger, the turbocharger is certainly damaged.
Using a pressure/vacuum pump, check that the turbocharger protection and turbocharging valve capsule
diaphragms do not leak.
Check the condition the motorised throttle valve in terms of clogging.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
17B-344V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP3 Idle speed faults
NOTESApply ALP3 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the inlet system sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery circuit (manifold - cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Measure the electrical resistance of the quadruple ignition module.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP03 / SIM32_V4C_ALP03 / SIM32_V50_ALP03 / SIM32_V54_ALP03
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.
17B-345V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP4 Faults occurring while driving
NOTESApply ALP4 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Check inlet line sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery system (manifold/cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP04 / SIM32_V4C_ALP04 / SIM32_V50_ALP04 / SIM32_V54_ALP04
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.
