2009 RENAULT TWINGO RS check engine

17B-183V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET039BRAKE PEDAL
STATUS
DEFINITIONDEPRESSED: This status indicates that the brake pedal is in the depressed position.
RELEASED: This status indicates that the brake pedal is in the released position.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
DEPRESSEDStatus ET039 is DEPRESSED when there is pressure on the brake pedal.
In the event of a fault,apply the interpretation of statuses ET704 Brake contact no. 1
and ET705 Brake contact no. 2.
RELEASEDStatus ET039 is RELEASED when there is no action on the brake pedal.
In the event of a fault,apply the interpretation of statuses ET704 Brake contact no. 1
and ET705 Brake contact no. 2.
SIM32_V44_ET039/SIM32_V4C_ET039/SIM32_V50_ET039/SIM32_V54_ET039
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-184V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the cruise control/speed limiter main On/Off switch
is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagram Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
"INACTIVE"No button has been pressed.
LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROLThe cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
SIM32_V44_ET042/SIM32_V4C_ET042/SIM32_V50_ET042/SIM32_V54_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-186V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 2
"INACTIVE"
When the main button is in rest position (or Neutral), status ET042 Cruise control/
speed limiter is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition on the switch connector on the following connection:
●AP10 of component 1081.
Disconnect the switch and with it in the rest position, check the insulation between
the following connections:
●AP10 and 3FX of component 1081.
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-187V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 3
LIMITER
When the driver presses the speed limiter switch, status ET042 Cruise control/
speed limiter becomes SPEED LIMITER.

If CRUISE CONTROL or INACTIVE appears although the driver pressed the switch
in the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition feed on the switch connector.
●AP10 of component 1081.
Disconnect the switch and when it is in the rest position, check the insulation
between:
●AP10 and 3FX of component 1081,
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-188V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 4
CRUISE
CONTROL
When the driver presses the cruise control switch, status ET042 Cruise control/
speed limiter becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears even though the cruise control button is
pressed, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition feed on the switch connector.
●AP10 of component 1081.
Disconnect the switch and when it is in the rest position, check the insulation
between:
●AP10 and 3FX of component 1081,
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3FX of component 1081 in
the cruise control position.
If the results of the checks are not correct, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-189V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET045CRUISE CONTROL/SPEED LIMITER SELECTOR SWITCH ON STEERING WHEEL
STATUS
DEFINITIONRESUME: This status indicates that the R button is pressed.
SUSPEND: This status indicates that the 0 is pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
INCREASEStatus ET413 becomes INCREASE when the cruise control + button is pressed.
This button is situated to the left of the steering wheel.
DECREASEStatus ET413 becomes INCREASE when the cruise control + button is pressed.
This button is situated to the left of the steering wheel.
SUSPENDStatus ET413 becomes SUSPEND when the 0 cruise control button is pressed.
This button is situated to the right of the steering wheel.
RESUMEStatus ET413 becomes RESUME when the R cruise control button is pressed.
This button is situated to the right of the steering wheel.
SIM32_V44_ET045/SIM32_V4C_ET045/SIM32_V50_ET045/SIM32_V54_ET045
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-190V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET048ACTUATOR RELAY CONTROL
STATUS
DEFINITIONACTIVE: The status indicates that the control is active.
INACTIVE: The status indicates that the control is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"
or
ACTIVEThis relay supplies the following actuators: the injectors, the throttle valve control,
the oxygen sensor heating, the bleed solenoid valve, the fuel vapour absorber
and connection 3FB of the injection computer.
In the event of a fault, see the interpretation of fault DF084 Actuator relay control
circuit.
SIM32_V44_ET048/SIM32_V4C_ET048/SIM32_V50_ET048/SIM32_V54_ET048
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-191V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET050ACTUATOR RELAY CONTROL
STATUS
DEFINITIONACTIVE: The status indicates that the canister bleed control is active.
INACTIVE: The status indicates that the canister bleed control is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"The petrol vapour rebreather bleed does not operate at idle speed.
Use command AC017 Canister bleed solenoid valve to check its operation.
In the event of a fault, see interpretation of fault DF081 Canister bleed solenoid
valve circuit.
SIM32_V44_ET050/SIM32_V4C_ET050/SIM32_V50_ET050/SIM32_V54_ET050
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.