2009 RENAULT TWINGO RS check engine

17B-342V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP1
CONTINUED 2
CHECK
ON
VEHICLE
(CONTINUED)
Use the Universal bornier to check the following connections on the vehicle
diagnostic socket:
●AP10 between components 225 and 1016 (+ after ignition feed) (for NEW
TWINGO or E33),
●AP10 between components 225 and 1337 (+ after ignition feed) (for CLIO III
or MODUS),
●BP32 between components 225 and 260 (+ Battery feed),
●3BB on component 225 (Earth).
If the connections are faulty and if there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Check the condition of the engine management computer connector (component
code 120).
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Use the universal bornier to check the continuity of the multiplex communication
lines:
●133B between components 120 and 645 (for NEW TWINGO or E33),
●133C between components 120 and 645 (for NEW TWINGO or E33),
●133B between components 120 and 1337 (for CLIO III or MODUS),
●133C between components 120 and 1337 (for CLIO III or MODUS).
If the connections are faulty and if there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
If the fault is still present, perform fault finding on the multiplex network (see 88B,
Multiplexing).
Disconnect the earth terminal of the computer from the negative battery terminal.
Check for an earth on connection N of the injection computer.
Check the continuity and insulation of the following connection:
●BP between components 120 and 107.
If the connection is faulty and if there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-343V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP2 The engine will not start
NOTESApply ALP2 after a complete check using the diagnostic tool.
If the starter motor does not operate, there may be a fault with the engine immobiliser. Check status ET341
Immobiliser code programmed, if YES apply the following procedure, if NO, run command SC017 Programming
injection immobiliser code, in the UCH in repair mode (see 17B, Petrol injection, Replacement of
components).
In the event of a fault, perform fault finding on the UCH (see 87B, Passenger compartment connection unit).
Check the condition of the battery.
Check the cleanliness, condition and tightness of the battery terminals.
Check that the battery is correctly earthed to the vehicle bodywork.
Check that the + battery leads are correctly connected.
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Check that the starter motor is properly connected.
Check that the starter operates correctly.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that there is fuel in the tank (fuel sender fault).
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check the sealing of the injectors, and that they are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP02 / SIM32_V4C_ALP02 / SIM32_V50_ALP02 / SIM32_V54_ALP02
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-347V7 MR-413-X44-17B000$220.mif
PETROL INJECTION
Fault finding – Tests17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
TEST 1 Petrol conformity check
WARNING
During this operation, it is essential to:
–refrain from smoking or bringing incandescent objects close to the work area,
–protect yourself against fuel splashes due to residual pressure in the pipes,
–wear safety goggles with side guards,
–wear leaktight gloves (Nitrile type).
IMPORTANT
–To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
–To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Remove 1 l of fuel at the fuel filter outlet, in the engine compartment (see MR 385 (Modus), MR 392 (Clio III),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 19C, Tank, Fuel tank: Draining), using a pneumatic
transfer pump (part no. 634-200) and place it in 1300 ml plastic cup (part no. 77 11 171 413).
Close the plastic cup with its cover (part no. 77 11 171 416) and let the fuel rest for approximately 2 minutes.
This type of plastic cup is used to prepare paint.
Is the fuel cloudy or does it
separate into two parts?Water is present in the petrol; the fuel is not correct.
Drain the fuel circuit, including the tank (see MR 385 (Modus),
MR 392 (Clio III), MR 411 (New Twingo), or MR 442 (E33),
Mechanical, 19C Tank, Fuel tank: Draining).
Visually compare the fuel removed with the correct petrol.
Are the samples identical?
YES
NO
YES
A
NO
B
SIM32_V44_TEST1/SIM32_V4C_TEST1/SIM32_V50_TEST1/SIM32_V54_TEST1