2009 RENAULT TWINGO tow

19A-30
COOLING
Coolant pump: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the engine undertray,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (80B, Headlights),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the throttle valve (see 12A, Fuel mixture, Throttle
valve: Removal - Refitting, page 12A-20) ,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the timing belt (see 11A, Top and front of engine,
Timing belt: Removal - Refitting, page 11A-27) ,
-the camshaft dephaser (see 11A, Top and front of
engine, Camshaft dephaser: Removal - Refit-
ting, page 11A-135) . Tightening torquesm
bolt 1 of the coolant
pump27 N.m
bolts 2 to 8 of the water
pump10 N.m
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.

19A-37
COOLING
Thermostat: Removal - Refitting
D4F, and 780 or 782
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove the water chamber (see 19A, Cooling, Wa-
ter chamber: Removal - Refitting, page 19A-40) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aPress on the spring mounting (1) .
aTurn the spring mounting (2) .
aRemove the thermostat (3) .
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the thermostat,
-the thermostat seal.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the thermostat fitted with a new seal.
aFit:
-the spring,
-the spring mounting.
aPress on the spring mounting.
aTurn the spring mounting.
III - FINAL OPERATION
aRefit the water chamber (see 19A, Cooling, Water
chamber: Removal - Refitting, page 19A-40) .
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
121758
121759
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-40
COOLING
Water chamber: Removal - Refitting
D4F, and 772 – D7F
19A
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aPart always to be replaced:
-water chamber seal.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRemove the air filter box (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aMove the water chamber hose clips to one side us-
ing the (Mot. 1448) or (Mot. 1202-01) or (Mot. 1202-
02).
aDisconnect the water chamber hoses.aRemove:
-the water chamber bolts (1) ,
-the water chamber.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aClean the gasket faces.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the water chamber with a new seal,
-the water chamber bolts.
aTorque tighten the water chamber bolts (10 Nm).
aConnect the water chamber hoses.
aFit the water chamber hose clips using the (Mot.
1448) or (Mot. 1202-01) or (Mot. 1202-02). Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Tightening torquesm
water chamber bolts10 Nm
D4F
113372
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-42
COOLING
Water chamber: Removal - Refitting
K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the front engine cover. Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
water chamber bolts10 N.m
intercooler air outlet
pipe clip at the damper
valve end5.5 N.m
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.
WARNING
The coolant helps to keep the engine running prop-
erly (heat exchange).
The system does not operate using pure water.
WARNING
Take care not to damage the bearing faces to pre-
vent any risk of coolant leaks.

19A-46
COOLING
Water chamber: Removal - Refitting
D4F, and 780 or 782
19A
REMOVAL - REFITTING
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDetach the turbocharger cooling pipe from the cylin-
der head.
aRemove the water chamber hose clips using the
(Mot. 1448).
aDisconnect the water chamber hoses.
aRemove the pipe from the heater matrix under the
water chamber.aRemove:
-the water chamber bolts (1) ,
-the water chamber (2) ,
-the water chamber seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the water chamber seal.
II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the water chamber with a new seal.
aScrew on the water chamber bolts without tightening
them.
aTorque tighten the water chamber bolts (10 N.m).
aConnect the water chamber hoses.
aFit the heater matrix pipe under the water chamber.
aRefit the water chamber hose clips using the (Mot.
1448).
aClip the turbocharger cooling pipe onto the cylinder
head. Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
water chamber bolts10 N.m
Note:
Use a cloth to protect the TDC sensor to prevent
any coolant entering the opening on the gearbox.
113372
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-48
COOLING
Water chamber: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the engine undertray.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) . Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Tightening torquesm
water chamber bolts
(initial torque)4 N.m
water chamber bolts12 N.m
heater matrix hose
bracket bolt10 N.m
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.

19A-51
COOLING
Engine cooling fan assembly: Removal - Refitting
C44, and K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) )
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove:
-the engine undertray bolts,
-the engine undertray,
-the front bumper ( (see Front bumper: Removal -
Refitting) ),
-the left-hand and right-hand headlights (see Halo-
gen headlight: Removal - Refitting) .
aRemove:
-the cooling radiator retaining lug bolt,
-the expansion bottle bolt onto the front upper cross
member,
-the air filter inlet air pipe bolt on the front upper
cross member.
aUnclip and then remove from the front upper cross
member:
-the air filter inlet air pipe,
-the expansion bottle.
aRemove the bonnet lock nuts.
aRemove the « cable - bonnet catch » assembly.
aRemove the front upper cross member ( (see Front
upper cross member: Removal - Refitting) )
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the electrical connectors on the engine
cooling fan assembly.
aUnclip:
-the engine cooling fan assembly wiring,
-the coolant hose at the bottom of the engine cool-
ing fan assembly.aPress on the engine cooling fan assembly locking
tabs (1) on the cooling radiator.
Note:
Do not unclip the bonnet release cable to avoid
damaging the cable clip on the lock.
AIR CONDITIONING
120324
Note:
Be careful not to press too hard on the tabs to
avoid breaking them.

19A-53
COOLING
Engine cooling fan assembly: Removal - Refitting
D4F, and 772, and AIR CONDITIONING or STANDARD HEATING – D7F, and AIR CONDITIONING or STANDARD
HEATING
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRemove:
-the battery ( (see Battery: Removal - Refitting) ),
-the battery tray ( (see Battery tray: Removal - Re-
fitting) ),
-the engine computer mounting,
aRemove:
-the air filter unit air inlet pipe bolt on the front end
panel,
-the air filter unit air inlet pipe,
-the air scoop.
aRemove the bonnet catch.
aMove the bonnet lock and release cable unit aside.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the engine cooling fan assembly con-
nectors.
aUnclip the fan assembly wiring harness.
aMove the motor-driven fan assembly wiring harness
aside.
aUnclip:
-the expansion bottle hose from the cooling fan as-
sembly,
-the cooling radiator bottom hose from the cooling
fan assembly.
aUnclip the engine cooling fan assembly.
aRemove the engine cooling fan assembly from
above. .
aIf replacing the fan:
-Remove the engine cooling fan bolts.
-Remove the fan from the fan assembly.
REFITTING
I - REFITTING PREPARATION OPERATION
aIf replacing the fan:
-Fit the engine cooling fan to the motor-driven fan
assembly.
-Refit the cooling fan bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine cooling fan assembly from above.
aClip the engine cooling fan assembly in place.
aClip:
-the expansion bottle hose from the cooling fan as-
sembly,
-the cooling radiator bottom hose from the cooling
fan assembly.
aFit the motor-driven fan assembly wiring harness.
aConnect the fan assembly connectors.
aClip the fan assembly wiring harness.
III - FINAL OPERATION
aRefit the bonnet catch.
aRefit:
-the engine computer mounting,
-the battery tray ( (see Battery tray: Removal - Re-
fitting) ),
-the battery ( (see Battery: Removal - Refitting) ).
aRefit:
-the air scoop,
-the air filter unit air inlet pipe,
-the air filter unit air inlet pipe bolt on the front end
panel. AIR CONDITIONING
AIR CONDITIONING