2009 RENAULT TWINGO wiring

87B-55
MR-413-X44-87B000$432.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
With automatic headlighting:DF109
PRESENT
OR
STORED
REAR FOG LIGHTS CONTROL CIRCUIT
CC.1: Short circuit to + 12 volts
CC.0: Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
The ignition is switched on and the rear fog lights are activated.
OR
Running AC009 Rear fog lights.
Note:
This fault only appears on vehicles fitted with automatic daytime running lights. Check
the presence of the rain/light sensor (component code 1415), then:
Check that the vehicle is configured with a rain/light sensor (component code 1415):
–Check that LC044 Rain/light sensor displays Present. If not, perform CF035
Rain/light sensor.
–Check that LC096 Automatic wiper function displays With. If not, carry out
CF194 "Automatic wiper function".
–Check that LC095 Automatic headlight function displays With. If not, carry out
CF193 "Automatic headlight function".
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), F39 (10 A) in the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the presence and condition of the rear fog lights relay (component code 230) (20A).
Replace the rear fog lights relay (component code 230) if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
connection of the UCH PE2 connector (component code 645) (tabs bent, oxidised, broken).
Check the condition and connection of the control stalk connector (component code 209) (tabs bent, oxidised,
broken).
Check for + 12 V (when there is a rear fog lights request) on connection 9P of components 172 and 173.
Check for earth on connection MF of component 172 and connection MYH on component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF109
MR-413-X44-87B000$432.mif
UCH
Vdiag No.: 44

87B-56
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF109
CONTINUED
Rear fog lights and rear fog light relay check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Right-hand rear fog light:
●Connection code 9P between components 172 and 230.
Left-hand rear fog light:
●Connection code 9P between components 173 and 230.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a rear fog lights request) on connection 9W of component 230. Check for + 12 V
on connection BP16 of component 230.
Rear fog lights relay check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 9W between components 230 and 645.
●Connection code BP16 between components 230 and 1016.
Control stalk check (component code 209):
Check the insulation, continuity and the absence of interference resistance of the following connections:
Check between the control stalk (component code 209) and the UCH (component code 645):
●Connection code 9B between components 645 and 209.
Check between the control stalk (component 209) and the passenger compartment fuse and relay box
(component code 1016):
●Connection code BPA2 between components 209 and 1016.
●Connection code BPA3 between components 209 and 1016.
Connection code MAM (for right-hand drive vehicles) or MAN (for left-hand drive vehicles) between component
209 and earth MAM (for right-hand drive vehicles) or MAN (for left-hand drive vehicles).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connections BPA2 and BPA3 of component 209.
Check for earth on connection MAM (for right-hand drive vehicles) or MAN (for left-hand drive vehicles) of
component 209.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies and connections of the control stalk (component code 209) are correct, replace the control stalk
(component code 209). (See MR 411 Mechanical 84A, Control - Signals, Lighting - signals switch: Removal
- Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-57
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF133
PRESENT
OR
STOREDDEADLOCKING MOTOR(S) CIRCUIT
CC.1: Short circuit to + 12 volts
CO.0: Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
The ignition is switched on and the deadlocking button has been pressed.
OR
Activation of AC035 Deadlocking.
Check that LC003 Deadlocking is definitely With. Otherwise, perform CF009
Deadlocking.
Check that LC040 Locking when driving is definitely With. Otherwise, perform
CF008 Locking when driving.
Ensure that the central door locking is correctly fixed; there must be no objects
preventing the central door locking from operating correctly.
Check that the doors and tailgate are closed correctly during the electrical
checks.
Check the presence and condition of fuse F14 (20 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of connectors PE1, PE2 and PE3 of the UCH (component code 645) (tabs
bent, oxidised, broken).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the electric central door locking connectors for the driver's and passenger's
doors (tabs bent, oxidised, bent etc.).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
When deadlocking, check the signal status on components 140 and 141 of the following connections using an
oscilloscope (refer to test1 Central door locking).
Right or left-hand door locks:
Oscilloscope red test pin on connection 20AP of component 140 or 141.
Oscilloscope black test pin on connection 20C of component 140 or 141.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF133

87B-58
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF133
CONTINUED 1
When unlocking, check the signal status on components 140 and 141 of the following connections using an
oscilloscope (refer to test2 Central door unlocking).
Right or left-hand door locks:
Oscilloscope red test pin on connection 20D of component 140 or 141.
Oscilloscope black test pin on connection 20C of component 140 or 141.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Central door deadlocking check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 20C between components 140 or 141 and 645.
●Connection code 20D between components 140 or 141 and 645.
●Connection code 20AP (specific to deadlocking) between components 140 or 141 and 1042.
●Connection code MAN between component 140 and earth MAN (for left-hand drive vehicles) and connection
code MAM between component 141 and earth MAM (for right-hand drive vehicles).
For manual gearbox:
●Connection code 86H between components 140 or 141 and 1016.
For sequential gearbox:
●Connection code H24 between components 140 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Central door locking relay check (for deadlocking):
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code BP3 between components 1042 and 1016.
●Connection code MAM between component 1042 and earth MAM.
●Connection code 20AP between components 1042 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supply and the earth of the central door locking relay (specific to deadlocking) are correct, replace the
relay.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-59
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF133
CONTINUED 2
If the supplies, central door locking connections, locking relay (specific to deadlocking) and central door locking
are correct, check the warning/central door locking switch (component code 1391).
Central door locking/warning switch check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 20AW between components 645 and 1391.
●Connection code 20M between components 645 and 1391.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the door lock concerned.
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-60
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF134
PRESENT
OR
STOREDHAZARD WARNING LIGHTS INDICATOR LIGHT CIRCUIT
CC.0: Short circuit to earth or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
Switching on the ignition and pressing the hazard warning lights button.
OR
Activating AC52 Hazard warning lights indicator light.
Note: If the hazard warning lights do not light up during emergency braking, check
that LC018 Illumination of hazard warning lights by ABS is definitely With.
Otherwise, run CF024 Illumination of hazard warning lights by ABS.
Check the presence and condition of fuse F42 (10 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the central door locking/warning switch connector (component code
1391) (tabs broken, bent, oxidised).
Check the condition and connection of connectors PE1 and PE2 of the UCH (component code 645) (tabs bent,
oxidised, broken).
Check for + 12 V on connection LPD of the locking/warning switch (component code 1391).
Check for earth on connection MAN of the locking/warning switch (component code 1391).
If the connector or connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 64F between components 1391 and 645.
●Connection code 64Q between components 1391 and 645.
●Connection code MAN between component 1391 and earth MAN.
●Connection code LPD between components 1391 and 1016.
●Connection code 20AM between components 1391 and 645.
●Connection code 20AW between components 1391 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supply, earth and connections are correct, replace the door locking/warning switch (component code
1391) (see MR 411 Mechanical 84A, Control - Signals, Hazard warning lights and central door locking:
Removal - Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF134

87B-62
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF135
DF136
CONTINUED
Check the continuity and insulation of the following connections:
●Connection code BPT between components 1415 and 645.
●Connection code 14S between components 1415 and 645.
●Connection code MAM between component 1415 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the rain/light sensor (component code 1415). (See MR 411 Mechanical
85A, Wiping - Washing, Rain and light sensor: Removal - Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-63
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF137
PRESENT
OR
STOREDUCH - ALTERNATOR CONNECTION
CO : Open circuit
1.DEF : Dialogue disrupted
CC.0 : Short circuit
NOTESThe fault is declared present after:
Switching on the ignition, starting the engine and waiting 30 seconds.
Check that the engine type is entered correctly using the configuration reading "Check
that LC023 Engine Type is correct". Otherwise perform CF028 Engine type.
Customer complaint:
The battery warning light comes on when the fault appears and goes out 10 seconds
after the fault disappears.
Note:
For petrol vehicles, the fault can be linked to a fault on the anti-interference capacitor
if it is present.
Check the condition and connection of the 2-track connector of the alternator (component code 103) and
connector PE1 of component 645 (tabs bent, oxidised, broken).
Check that the voltage is between 5 V and 10 V on connection 2N between components 103 and 645.
Check the continuity and insulation of the following connections:
●Connection code 2N between components 103 and 645.
●Connection code BPDA between components 103 and 163.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF135 / UCH_V44_DF136