2009 RENAULT TWINGO air condition

87B-24
MR-413-X44-87B000$336.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Summary of sensors and actuators on which the UCH can carry out fault finding (with the corresponding
engineering office codes).
Tool fault Associated DTC Diagnostic tool title
DF0019510 UCH
DF0119522 Rain/light sensor circuit
DF01295D1 Right-hand direction indicator circuit
DF01395D0 Left-hand direction indicator circuit
DF0279550 External temperature sensor circuit
DF04095A0 Rear screen wiper park position
DF0419560 Heated rear screen warning light circuit
DF0429558 Air conditioning warning light circuit
DF0549501 Computer
DF0629580 Starter relay control circuit
DF06595F0 Electric window authorisation connection
DF0829570 Door locking button indicator light circuit
DF08795C2 Side lights relay control circuit
DF08895C3 Dipped beam headlights relay control circuit
DF09795 A1 Windscreen wiper park position control
DF09895C4 Main beam headlight relay control circuit
DF10895C5 Front fog lights control circuit
DF10995C6 Rear fog lights control circuit
DF1339574 Deadlocking motor(s) circuit
DF13495D2 Hazard warning lights indicator light circuit
DF1359520 Rain detector
DF1369521 Light sensor
DF13796B1 UCH - Alternator connection
DF13896B2 Alternator
DF1399660 Interior lights
DF14096B3 Voltage regulator
DF21295B0 Alarm circuit
MR-413-X44-87B000$336.mif
UCH
Vdiag No.: 44

87B-25
MR-413-X44-87B000$384.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
DF001
PRESENT
OR
STOREDUCH
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the ignition is switched off and back on.
If the fault is stored, clear the fault, switch off the ignition and disconnect the F8 (15A) fuse of the UCH supply
(component code 645) on the passenger compartment fuse and relay box (component code 1016).
–Refit the fuse and switch the ignition back on.
–Request locking and then unlocking, then start the engine.
Check the condition and connection of the PE1, PE2 and PE3 connectors of the UCH (component code 645)
(tabs pushed back, oxidised, broken).
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + after ignition feed on connection AP43 of component 645.
Check for + accessories feed on connection SP2 (for vehicles fitted with a manual gearbox) or SP15
(for vehicles fitted with a sequential gearbox) of component 645.
Check for earth on connection NAM of component 645. Check the earth on connection MAM of component 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault reappears as stored, contact Techline.
If the fault does not reappear, switch the lighting, wipers, vehicle locking and climate control request controls on
and off several times, then read the faults again.
If the fault is still present. Do not operate on the computer, contact Techline.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline): reconfigure the new
UCH (see Configurations and programming).
Deal with any other faults.
UCH_V44_DF001
MR-413-X44-87B000$384.mif
UCH
Vdiag No.: 44

87B-26
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF011
PRESENT
OR
STOREDRAIN/LIGHT SENSOR CIRCUIT
1.DEF : Open circuit or short circuit
NOTESConditions for applying the fault finding procedure to stored faults:
Switch on the ignition, activate automatic headlighting by quickly performing the
following manipulation twice: control stalk (component code 209) on zero position →
control stalk (component code 209) in Side light position.
Status ET114 “Wiper request by rain sensor” should be “Low speed” or “High
speed” when the water runs over the rain/light sensor on the windscreen or
status ET115 “Request for lights to be switched on by light sensor” should be
“Present” by placing an opaque cover over the rain/light sensor.
Note:
If there is an open circuit on connection BPT, there is a malfunction on the
electric windows, rain/light sensor, interior light(s) and luggage compartment
light.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, quickly perform the following cycle twice to activate the automatic
headlighting function: Monolever (component code 209) OFF → Monolever (component code 209) in Side light
ON position.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that LC044 "Rain/light sensor" displays "Present". If not, carry out CF035 "Rain/light sensor".
Check that LC096 "Automatic wiper function" displays "With". If not, carry out CF194 "Automatic wiper
function".
Check that LC095 "Automatic headlight function", displays "With". If not, carry out CF193 "Automatic
headlight function".
Check the condition and the positioning of fuses F2 (15A), F8 (15A), F19 (5A), F27 (5 A) depending on the
equipment and F29 (15A) on the passenger compartment fuse and relay box (component code 1016).
Replace the fuse(s) or repair if necessary.
Check the condition and connection of the PE1, PE2 and PE3 connectors of the UCH (component code 645)
(tabs pushed back, oxidised, broken).
Check for + after ignition feed on connection AP43 of component 645.
Check for + accessories feed on connection SP2 (for vehicles fitted with a manual gearbox) or SP15
(for vehicles fitted with a sequential gearbox) of component 645.
Check for earth on connection NAM of component 645. Check the earth on connection MAM of component 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF011

87B-27
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
Rain/light sensor check:DF011
CONTINUED
Check the continuity and insulation of the following connections:
●Connection code AP43,
●Connection code SP2,
●Connection code SP15.
Between components 645 and 1016.
●Connection code MAN or MAM between component 645 and earth MAN or MAM (depending on the driving
layout, right- or left-hand drive).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, check the rain/light sensor (component code 1415).
Check the condition and connection of the 3-track rain/light sensor connector (component code 1415) (tabs
bent, broken or oxidised).
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
Check the continuity and insulation of the following connections:
●Connection code BPT between components 645 and 1415.
●Connection code 14S between components 645 and 1415.
●Connection code MAM between components 1415 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the sensor is not dirty.
Check that the sensor is correctly bonded to the windscreen. (see MR 411 85A, Wipers - Washers, Rain and
light detector: Removal - Refitting)
If the fault is still present, replace the rain/light sensor (component code 1415).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-28
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF012
PRESENT
RIGHT-HAND DIRECTION INDICATOR CIRCUIT
CC.0 : Short circuit to earth
C0.1 : Open circuit or short circuit to + 12 V
1.DEF : Bulb(s) not working or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault appears after:
The right-hand indicator stalk is activated.
OR
Activation of AC023 Right-hand indicator.
Check that fuses F13 (30A) and F15 (5 A) are sound and correctly fitted in the passenger compartment fuse and
relay box (component code 1016).
Check the bulbs and condition of the bulb supports.
Replace the bulbs if necessary.
With command AC023 Right-hand indicator running, check for + 12 V on the following connection:
●Connection code 64D.
Between components 256 and 645.
Between components 268 and 645.
Between components 173 and 645.
Check the continuity on the following connection:
●Connection code 64D.
Between components 256 and 645.
Between components 268 and 645.
Between components 173 and 645.
Check for earth on the following connections:
●Connection code MAS between component 256 and earth MAS.
●Connection code MAS between component 268 and earth MAS.
●Connection code MF between component 173 and earth MF.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the feeds and earths are correct, check the monolever (component code 209).
If the feeds and earths are not correct, check the condition and connection of the horn and lights switch
connector (component code 209) and the UCH 40-track connector PE2 (component code 645) (tabs bent,
broken or oxidised).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF012P

87B-30
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF013
PRESENT
LEFT-HAND DIRECTION INDICATOR CIRCUIT
CC.0 : Short circuit to earth
C0.1 : Open circuit or short circuit to + 12 V
1.DEF : Bulb(s) not working or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault appears after:
The left-hand indicator stalk is activated.
OR
Running AC022 Left-hand indicator.
Check that fuses F13 (30A) et F15 (5 A) are sound and correctly fitted in the passenger compartment fuse and
relay box (component code 1016).
Check the bulbs and condition of the bulb supports.
Replace the bulbs if necessary.
With command AC022 Left-hand indicator running, check for + 12 V on the following connection:
●Connection code 64C.
Between components 256 and 645.
Between components 268 and 645.
Between components 173 and 645.
Check the continuity on the following connection:
●Connection code 64C.
Between components 256 and 645.
Between components 268 and 645.
Between components 173 and 645.
Check for earth on the following connections:
●Connection code MAS between component 256 and earth MAS.
●Connection code MAS between component 268 and earth MAS.
●Connection code MF between component 173 and earth MF.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the feeds and earths are correct, check the monolever (component code 209).
If the feeds and earths are not correct, check the condition and connection of the horn and lights switch
connector (component code 209) and the UCH 40-track connector PE2 (component code 645) (tabs bent,
broken or oxidised).
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF013P

87B-32
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF027
PRESENT
OR
STOREDEXTERNAL TEMPERATURE SENSOR CIRCUIT
1. DEF : Abnormal voltage
CC.0 : Short circuit to earth
C0.1 : Open circuit or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the ignition is switched off and back on.
Note:
If the exterior temperature sensor is disconnected or the vehicle is not equipped with
an exterior temperature sensor, the temperature displayed is the default temperature
of 215 ˚C.
Check whether the right-hand door mirror is fitted with an exterior temperature sensor. (See MR 411 mechanical
systems 62A, Air conditioning, Air conditioning: List and location of components).
If the vehicle is fitted with an exterior temperature sensor, deal with the following fault finding procedure.
If NO, the vehicle is not fitted with this:
Check that the vehicle is configured without external temperature sensor (component code 240 for left-hand
drive vehicles) or (component code 239 for right-hand drive vehicles):
Check that LC002 "External temperature sensor" is "WITHOUT". Otherwise perform CF029 "External
temperature sensor".
Check the temperature sensor 2-track connector (bent, oxidised, broken tabs).
Check the PE2 40-track connector of the UCH, component code 645 (tabs bent, oxidised, broken).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code 47D between components 240 (for left-hand drive vehicles) or 239 (for right-hand drive
vehicles) and 645.
●Connection code 47C between components 240 (for left-hand drive vehicles) or 239 (for right-hand drive
vehicles) and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the sensor (connector disconnected) on connections 47C and 47D.
Temperature (˚C)
0
5
10
15
20
25
30
35Sensor resistance (Ω) ± 50 Ω
5980
5020
4280
3530
2900
2300
2010
1620
Replace the sensor if not correct (see MR 411 Mechanical systems 62A, Air conditioning, Exterior air
temperature sensor: Removal - Refitting).
If there is a fault, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF027

87B-33
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF040
PRESENT
OR
STOREDREAR SCREEN WIPER PARK POSITION
1.DEF : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault appears after:
The ignition is switched off and back on again and the rear wipers are operated using
the wiping stalk.
OR
Activating AC007 Rear screen wipers.
This fault may appear if the rear screen wiper motor (component code 211) is forced (e.g.: used on a dry screen,
snow on the screen, etc.).
Check that fuse F36 (15 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track rear screen wiper motor connector (component code 211)
(broken, bent, oxidised tabs).
Activate the rear screen wiper, check for + 12 V on connection 36A of the rear screen wiper
motor connector (component code 211).
Check that the earth on connection MYH of the rear screen wiper motor connector (component code 211) is in
perfect condition.
Check the condition and connection of the UCH 40-track PE1 connector (component code 645) (tabs broken,
bent or oxidised) and the 3-track rear screen wiper motor connector (component code 211).
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF040