2009 RENAULT TWINGO headlights

87B-7
MR-413-X44-87B000$096.mif
V5
87B
ENGINE HARNESS
FRONT ENGINE WIRING & ADDITIONAL HEADLIGHTS
DOOR WIRING
CEILING WIRING
PASSENGER COMPARTMENT WIRING
REAR BUMPER WIRING
TAILGATE WIRING
1UCH
2Passenger Compartment Relay/Fuse Box
3Electric power-assisted steering.
4Transponder ring.
5Air conditioning panel.
6One touch window/anti-pinch module.
7Exterior temperature sensor.
8Rain/light sensor & interior temperature sensor.
9Anti-pinch/sunroof.
2ABS computer.
2Injection computer.
3Preheating unit.
4Sequential gearbox computer.
5Engine fuse and relay box.
6Alternator.
7
2
61
2
3
5
4
8
5
7
43
1
6
9
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding
- List and location of components
MR-413-X44-87B000$096.mif
UCH
Vdiag No.: 44

87B-12
MR-413-X44-87B000$192.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Role of components87B
CONTINUED (Functions managed by the different UCH ranges on the New Twingo):
L1
Entry levelL2
Mid-rangeL3
Top of the
range
Lighting
Exterior lighting
Side, dipped beam, headlightsX
Direction indicators and hazard warning lightsXX X
One-touch front fog lightsX
One-touch rear fog lightsX
Lights on warning lightXX X
Hazard warning lights when decelerating hardXX X
Illumination of hazard warning lights when airbag triggeredXX X
Illumination of indicators when locking/unlockingXX
Automatic lighting when driving and stationaryX
Delayed extinction of headlights when stationary X
Daytime running lights onX
Lights switch off when driver's door openedX
Interior lighting
Interior lights supply (no gradual dimming function)X
Interior lights supply (gradual dimming)XX
Wipers
Windscreen wipers managementXX X
Automatic management of front wipers with rain sensorX
Rear wipersXX X
Windscreen and rear screen washersXX X
Energy management
Starter managementXX X
Controlled alternator (BSS connection)XX X

87B-21
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Functions available and operating mode
–Deadlocking (CF009)
This function enables you to disable the interior door opening control. This function is activated by a second locking
request from the key or the electric central locking switch.
This function is only available on vehicles fitted with a top of the range UCH.
–Hazard warning lights activated by ABS (CF024)
This function is available for all countries except Brazil, Finland, Great Britain, Japan and Sweden.
For Brazil, Great Britain, Japan, Sweden and Finland configure NONE.
For other countries, configure WITH.
In the event of braking causing rapid deceleration, the ABS computer transmits an activate hazard warning lights
request via the multiplex network to the UCH.
–New vehicle storage mode (LC041 New vehicle storage mode)
If this mode is activated, consult the command, see LC041 "New vehicle storage mode" and contact the Techline.
–Daytime running lights
This configuration automatically activates the side lights and dipped beam headlights when the engine is running,
without the driver using the lighting controls.
To be used in accordance with legislative requirements.
CF031 Calibration:
When replacing the UCH computer, perform this configuration.
This command lasts approximately 30 seconds.

87B-24
MR-413-X44-87B000$336.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Summary of sensors and actuators on which the UCH can carry out fault finding (with the corresponding
engineering office codes).
Tool fault Associated DTC Diagnostic tool title
DF0019510 UCH
DF0119522 Rain/light sensor circuit
DF01295D1 Right-hand direction indicator circuit
DF01395D0 Left-hand direction indicator circuit
DF0279550 External temperature sensor circuit
DF04095A0 Rear screen wiper park position
DF0419560 Heated rear screen warning light circuit
DF0429558 Air conditioning warning light circuit
DF0549501 Computer
DF0629580 Starter relay control circuit
DF06595F0 Electric window authorisation connection
DF0829570 Door locking button indicator light circuit
DF08795C2 Side lights relay control circuit
DF08895C3 Dipped beam headlights relay control circuit
DF09795 A1 Windscreen wiper park position control
DF09895C4 Main beam headlight relay control circuit
DF10895C5 Front fog lights control circuit
DF10995C6 Rear fog lights control circuit
DF1339574 Deadlocking motor(s) circuit
DF13495D2 Hazard warning lights indicator light circuit
DF1359520 Rain detector
DF1369521 Light sensor
DF13796B1 UCH - Alternator connection
DF13896B2 Alternator
DF1399660 Interior lights
DF14096B3 Voltage regulator
DF21295B0 Alarm circuit
MR-413-X44-87B000$336.mif
UCH
Vdiag No.: 44

87B-45
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
With automatic headlighting:DF088
PRESENT
OR
STORED
DIPPED BEAM HEADLIGHTS RELAY CONTROL CIRCUIT
CC.1 : Short circuit to + 12 volts
CC.0 : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault reappears after:
The ignition is switched on and the side lights are activated.
OR
Running AC054 Dipped headlights
Note:
This fault only appears on vehicles fitted with automatic headlighting.
Check for the rain/light sensor (component code 1415) then:
–Check that the vehicle has a rain/light sensor (component code 1415).
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC096 "Automatic wiper function" displays "With". If not, carry out
CF194 "Automatic wiper function".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
Check that fuses F13 (30A), F15 (5A), F25 (5 A), F34 (15 A) and F35 (15 A) are sound and correctly fitted in the
passenger compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the presence and condition of the dipped headlights relay (component code 281) (20A).
Replace the dipped headlights relay (component code 281) if necessary.
Check the correct positioning and condition of the bulb concerned.
Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the UCH 40-track connector PE2 (component code 645) (tabs bent,
oxidised or broken).
Check the condition and connection of the horn and lights switch connector (component code 209) (tabs bent,
oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF088

87B-46
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF088
CONTINUED 1
Dipped headlights check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Front right-hand dipped beam headlight:
●Connection code CPD between components 226 and 1016.
●Connection code MAR between component 226 and earth MAR.
Front left-hand dipped beam headlight:
●Connection code CPG between components 227 and 1016.
●Connection code MAS between component 227 and earth MAS.
Check for + 12 V (when there is a dipped headlights request) on connection CPD of component 226 and
connection CPG of component 227.
Check for the earth on connection MAR of component 226 and on connection MAS of component 227.
Check for + 12 V (when dipped headlights are requested) on connection CSO of component 281.
Check for + 12 V (when dipped headlights are requested) on connection 78M of component 281.
Check for + 12 V on connection BP59 of component 281.
Dipped headlights relay check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code CSO between components 281 and 1016.
●Connection code 78M between components 281 and 645.
●Connection code BP59 between components 281 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-50
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
With automatic headlighting:DF098
PRESENT
OR
STORED
MAIN BEAM HEADLIGHT RELAY CONTROL CIRCUIT
CC.1 : Short circuit to + 12 volts
CC.0 : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault reappears after:
The ignition is switched on and the main beam headlights are activated.
OR
Running AC062 Main beam headlights
Note:
This fault only appears on vehicles fitted with automatic daytime running lights. Check
for the rain/light sensor (component code 1415) then:
–Check that the vehicle has a rain/light sensor (component code 1415).
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out -
CF035 "Rain/light sensor".
–Check that LC096 "Automatic wiper function" displays "With". If not, carry out
CF194 "Automatic wiper function".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
Check the presence and condition of fuses F15 (5 A), F25 (15 A), F32 (10 A) and F33 (10 A) on the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the presence and condition of the main beam headlights relay (component code 1574) (20A).
Replace the main beam headlights relay (component code 1574) if necessary.
Check the correct positioning and condition of the bulb concerned.
Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the UCH PE2 connectors (component code 645) (tabs bent, oxidised or
broken).
Check the condition and connection of the horn and lights switch connector (component code 209) (tabs bent,
oxidised, broken).
Check for + 12 V (when there is a main beam headlights request) on connection RPD of components 226 and
227. Check for an earth on connection MAR of component 226 and connection MAS on component 227.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF098

87B-51
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF098
CONTINUED 1
Main beam headlights check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Front right-hand main beam headlight:
●Connection code RPD between components 226 and 1016.
●Connection code MAR between component 226 and earth MAR.
Front left-hand main beam headlight:
●Connection code RPG between components 227 and 1016.
Connection code MAS between component 227 and earth MAS.
Check for + 12 V (when main beam headlights are requested) on connection R of component 1574.
Check for + 12 V (when main beam headlights are requested) on connection 11A of component 1574. Check for
+ 12 V on connection BP11 of component 1574.
Main beam headlights relay check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code R between components 1016 and 1574.
●Connection code 11A between components 1574 and 645.
●Connection code BP11 between components 1574 and 597.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Checking the monolever (component code 209):
Check the insulation, continuity and the absence of interference resistance on the following connections:
Check between the monolever (component code 209) and the UCH:
●Connection code 11Q between components 645 and 209.
Hazard lights:
●Connection code 11R between components 209 and 654.
Check between the monolever (component code 209) and the passenger compartment fuse and relay box
(component code 1016):
●Connection code BPA2 between components 209 and 1016.
●Connection code BPA3 between components 209 and 1016.
●Connection code MAN (left-hand drive) or MAM (right-hand drive) between component 209 and the earth
MAN (left-hand drive) or MAM (right-hand drive).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.