2009 RENAULT TWINGO sensor

17B-318V7 MR-413-X44-17B000$172.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR571PINKING SIGNAL
PARAMETER
DEFINITIONThis parameter indicates the pinking signal.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine running and engine coolant temperature > 80˚C.
This parameter varies according to the pinking status in the combustion chamber.
In the event of a fault, apply the interpretation of fault DF330 Pinking sensor circuit.
SIM32_V44_PR571 / SIM32_V4C_PR571 / SIM32_V50_PR571 / SIM32_V54_PR571
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-323V7 MR-413-X44-17B000$172.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
For CLIO III or MODUS only
PR743ALCOHOL LEVEL ESTIMATED IN THE TANK
PARAMETER
DEFINITIONThis parameter is used to estimate the percentage of alcohol contained in the petrol in
the main tank.
NOTESThere must be no present or stored faults.
Refer to CLIO III or MODUS Wiring Diagram Technical Note.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature
> 80˚C.
This percentage must be between:
0 < PR743 < 100%
This parameter allows the computer to estimate the alcohol level contained in the petrol.
Status ET671 Alcohol level programming should be COMPLETED. This indicates that the percentage of alcohol
in the tank has been detected.
If status ET671 Alcohol level programming is NOT COMPLETED, repeat the programming procedure (see
Configurations and programming, Alcohol level programming).
Disconnect the battery and the injection computer.
Check the cleanliness and condition of the connections
Using the universal bornier, check the insulation and continuity on the following connections:
●3GH between components 887 and 120.
●3GK between components 887 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the upstream oxygen sensor.
If the fault is still present, contact the Techline.
SIM32_V44_PR743 / SIM32_V4C_PR743 / SIM32_V50_PR743 / SIM32_V54_PR743
AFTER REPAIRRepeat the conformity check from the start.

17B-326V7 MR-413-X44-17B000$172.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
For CLIO III or MODUS only
PR926ALCOHOL FUEL ADAPTIVE CORRECTION
PARAMETER
DEFINITIONThis parameter indicates the alcohol adaptive correction.
NOTESThere must be no present or stored faults.
Refer to CLIO III or MODUS Wiring Diagram Technical Note.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature
> 80˚C.
The correction of the injection duration depends on the estimated alcohol level in the main tank, and the cold
starting procedure for the engine with the Hi-Flex system is carried out accordingly.
Status ET671 Alcohol level programming should be COMPLETED. This indicates that the percentage of alcohol
in the tank has been detected.
This percentage must be between:
0 < PR926 < 100%.
If status ET671 is Not completed, repeat the programming procedure (see Configurations and programming,
Alcohol level programming).
Disconnect the battery and the injection computer.
Check the cleanliness and condition of the connections.
Use the "Universal bornier" to check the insulation and the continuityof the following connections:
●3GH between components 887 and 120.
●3GK between components 887 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the upstream oxygen sensor.
If the fault is still present, contact the Techline.
SIM32_V44_PR926 / SIM32_V4C_PR926 / SIM32_V50_PR926 / SIM32_V54_PR926
AFTER REPAIRRepeat the conformity check from the start.

17B-327V7 MR-413-X44-17B000$180.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
CLEAR:
ACTIVATION:Tool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used for clearing the stored faults from the
computer.
RZ005 programmingThis command enables you to reinitialise the entire vehicle
configuration.
Tool
commandDiagnostic tool title Comments
AC015 Fuel pump relayThis commands enables the fuel pump to be listened to.
AC017Canister bleed solenoid
valveThis command enables the canister bleed solenoid valve to be
opened.
AC027 Motorised throttleThis command enables the motorised throttle to be opened.
AC038Low speed fan assembly
relayThis command enables the fan unit relay to be controlled.
AC039High speed fan assembly
relayThis command enables the fan unit relay to be controlled.
AC079 Actuator static testThis activation enables several actuators to be controlled.
AC117Upstream O2 sensor
heatingThis command enables the upstream sensor heating to be
controlled.
AC118Downstream O2 sensor
heatingThis command enables the downstream sensor heating to be
controlled.
AC156Camshaft dephaser 1
(only for CLIO III or MODUS)This activation enables the camshaft dephaser to be controlled.
AC180Air conditioning
compressor relay controlThis command enables the air conditioning compressor relay to
be controlled.
AC199Controlled coolant
thermostat
(only for Vdiag 4C)The activation of this command enables the controlled coolant
thermostat to be opened.
AC253Camshaft dephaser:
Normal controlThis activation enables the camshaft dephaser solenoid valve to
be fully controlled in a repetitive manner with the ignition on.
AC254Camshaft dephaser:
On/off controlThis activation enables the camshaft to be completely shifted in
relation to the pulley with the engine idling.
PETROL INJECTION
Fault finding – Command summary table

17B-328V7 MR-413-X44-17B000$180.mif
PETROL INJECTION
Fault finding – Command summary table17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
SPECIFIC COMMAND:
Tool
commandDiagnostic tool title Comments
SC001 Write saved dataThis command is used to rewrite saved data when the
computer is reprogrammed or replaced.
SC003 Save computer dataThis command is used to save data to be rewritten when the
computer is reprogrammed or replaced.
SC006Start OBD test: Catalytic
converterThis command is used to test the condition of the catalytic
converter. (Not valid for Vdiag 44).
SC007 Start OBD test: O2 sensorsThis command is used to test the condition of the oxygen
sensor.
VP008 Injector control unlockingThis command is used to unlock the injectors.
VP010 Write VINThis command is used to rewrite the VIN.
VP013 Injector control lockingThis command is used to lock the injector control.

17B-335V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC117UPSTREAM O2 SENSOR HEATING
NOTESThere must be no present or stored faults.
Run command AC117.
Using a multimeter, check for 10 earthings on connection 3GH of the upstream O2 sensor.
SIM32_V44_AC117 / SIM32_V4C_AC117 / SIM32_V50_AC117 / SIM32_V54_AC117
AFTER REPAIRIf the throttle valve has been replaced, reinitialise the RZ005 programming.
Carry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-336V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC118DOWNSTREAM O2 SENSOR HEATING
NOTESThere must be no present or stored faults.
Run command AC118.
Using a multimeter, check for 10 earthings on connection 3GJ of the downstream O2 sensor.
SIM32_V44_AC118 / SIM32_V4C_AC118 / SIM32_V50_AC118 / SIM32_V54_AC118
AFTER REPAIRIf the throttle valve has been replaced, reinitialise the RZ005 programming.
Carry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-340V7 MR-413-X44-17B000$210.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP1 No dialogue with the computer
NOTESUse the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Test the diagnostic tool on another vehicle which is in perfect working order.
Check that the sensor's green indicator light comes on.
If communication with the second vehicle is impossible, follow the instructions in the CLIP diagnostic tool test
section.
If communication with the second vehicle is impossible, follow the instructions in the Vehicle check section.
DIAGNOSTIC
TOOL CHECKCheck the cleanliness and condition of the diagnostic socket contacts on
the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and
the cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the sensor to the CLIP tool, and the cleanliness
and condition of the connections.
Check the cleanliness and condition of the CLIP socket.
If the fault is still present, contact the Techline.
SIM32_V44_ALP01 / SIM32_V4C_ALP01 / SIM32_V50_ALP01 / SIM32_V54_ALP01
PETROL INJECTION
Fault finding – Fault Finding Chart
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.