2009 PONTIAC VIBE ignition

Playing a CD
The CD player can play the smaller
3 inch (8 cm) single CDs with an
adapter ring.
1. Insert a CD label side up
partway into the slot.
2. The CD player pulls the CD in
and begins playing.
3. The CD symbol and track
number displays.
4. The CD stays in the player if the
ignition or radio is turned off.
5. If the CD was the last source
selected, it resumes playing
when the radio is turned on.
Y(EJECT):Press and release to
eject a CD. Once ejected it can be
removed. If the CD is not removed
after several seconds the CD player
automatically pulls the disc back into
the player and starts playing.TUNE ADJ:Turn the TUNE ADJ
knob to select tracks on the CD.
ySEEK TRACKz:Pressyto
go to the start of the current
track, if more than ten seconds
have played. Press
zto go to the
next track. Holding or pressing
yorzmultiple times causes the
player to continue moving backward
or forward through the tracks on
the CD.
(FWD REV)(Fast Forward/
Fast Reverse):Press and hold
(
to advance playback quickly within a
track. Release to resume playing the
track. Press and hold
)to reverse
playback quickly within a track.
Release to resume playing the track.
BAND:Press to listen to the radio
when a CD is playing.CD/AUX (CD/Auxiliary):Press to
play a CD when listening to the radio.
Press the CD/AUX button again and
the system begins playing audio from
the connected portable audio player.
If a portable audio player is not
connected, “No Input Device Found”
displays.
See “Using the Auxiliary Input Jack”
later in this section.
INFO (Information):Press to
switch the display between the
track number, elapsed time of the
track, and the time. When the
ignition is off, press this button to
display the time.
EQ (Equalization):Press to select
an equalization setting while playing
a CD. See “EQ” listed previously for
more information. If an EQ setting is
selected for a CD, it is activated each
time a CD is played.
Infotainment 6-7
2009 - Pontiac Vibe Owner Manual

Music Navigator
The music navigator feature lets
MP3 CDs play in order by artist or
album.
The MP3 player scans the disc
to sort the les by artist and
album ID3 tag information.
It can take several minutes to
scan the disc depending
on the number of MP3 les
recorded to the CD-R.
The radio starts playing while
the disc is being scanned.
After the scan is nished,
the disc starts playing.
Playing an MP3
The MP3 player can play the
smaller 3 inch (8 cm) single CDs
with an adapter ring.
1. Insert a CD label side up
partway into the slot.
2. The CD player pulls the CD in
and begins playing.3. The CD stays in the player if the
ignition or radio is turned off.
4. If the CD was the last source
selected, it resumes playing
when the radio is turned on.
Y(EJECT):Press and release
to eject a CD. Once the disc is
ejected it can be removed.
If the CD is not removed after
several seconds the CD player
automatically pulls the disc back
into the player and starts playing.
ySEEK TRACKz:Press to go to
the start of the current track, if
more than ten seconds have played.
Press
zto go to the next track.
Holding or pressing
yorzmultiple
times will cause the player to
continue moving backward or
forward through the tracks on
the CD.
(FWD REV)(Fast Forward/
Fast Reverse):Press and hold
)
to advance playback quickly within
a track. Release
(to resume
playing the track. Press and hold
)
to reverse playback quickly within a
track. Release
(to resume
playing the track.
BAND:Press to listen to the radio
when a CD is playing.
INFO (Information):Press when
an MP3 CD is loaded, then press
the button below the Song, Artist,
Album, or Folder label to view
the information.
CD/AUX (CD/Auxiliary):Press to
play a CD when listening to the
radio.
Press the CD/AUX button again and
the system begins playing audio
from the connected portable audio
player. If a portable audio player
is not connected, “No Input Device
Found” displays.
Infotainment 6-11
2009 - Pontiac Vibe Owner Manual

Recirculation
?(Recirculation):Press to
turn the recirculation mode on or off.
An indicator light shows that it is on.
This mode recirculates the air inside
the vehicle and helps to heat or cool
the air more quickly. It can be used to
prevent outside air and odors from
entering the vehicle.
Press the button again to turn
the recirculation mode off and the
outside air mode on. Recirculation
is automatically turned off when the
climate control system mode knob
is turned to defog, defrost, or is
positioned between modes.
Rear Window Defogger
The rear window defogger uses a
warming grid to clear fog from
the rear window. It will only work
when the ignition is in the ON/RUN
position.
=(Rear Defogger):Press to turn
the rear window defogger on or off.
An indicator light shows that it is on.
The rear window defogger stays on
until it is manually turned off. Clear
any snow from the rear window.
If the ignition is turned off, while
the rear window defogger is on, the
defogger turns back on automatically
when the ignition is in the ON/RUN
position again.
Notice:Do not use a razor blade
or sharp object to clear the inside
rear window. Do not adhere
anything to the defogger grid lines
in the rear glass. These actions
may damage the rear defogger.
Repairs would not be covered
by your warranty.
Outlet Adjustment
Use the air outlets located in
the center and outboard sides of
the instrument panel, to change the
direction of the air owing through
the vents.
Operation Tips

Clear away any ice, snow or
leaves from the outside air
inlets at the base of the
windshield.
Use of non-GM approved hood
deectors can adversely affect
the performance of the system.
Keep the area under the
front seats clear of objects for
more effective air circulation.
If the airow seems low when
the fan is at the highest setting,
the passenger compartment air
lter might need to be replaced.
For more information, see
Passenger Compartment Air
Filter later in this section.
Climate Controls 7-3
2009 - Pontiac Vibe Owner Manual

Driving and
Operating
Starting and Operating
Your Vehicle
New Vehicle Break-In.........8-2
Ignition Positions................8-2
Retained Accessory
Power (RAP).....................8-4
Starting the Engine.............8-4
Engine Coolant Heater.......8-5
Automatic Transmission
Operation (Four Speed). . . .8-6
Automatic Transmission
Operation (Five Speed).....8-8
Manual Transmission
Operation........................8-11
Parking Brake...................8-12
Shifting Into Park..............8-13
Shifting Out of Park..........8-14
Parking the Vehicle
(Manual Transmission). . . .8-15
Parking Over Things
That Burn........................8-16
Engine Exhaust.................8-16
Running the Vehicle
While Parked..................8-17
Driving Your Vehicle
Defensive Driving..............8-17
Drunk Driving....................8-18
Control of a Vehicle..........8-18
Braking.............................8-19
Antilock Brake
System (ABS).................8-20
Traction Control
System (TCS).................8-21
All-Wheel Drive (AWD)
System............................8-22
StabiliTrak®System..........8-22
Steering............................8-23
Off-Road Recovery............8-24
Passing.............................8-25
Loss of Control.................8-25
Driving at Night.................8-26
Driving in Rain and on
Wet Roads......................8-27
Before Leaving on a
Long Trip........................8-28
Highway Hypnosis.............8-28
Hill and Mountain Roads. . .8-28
Winter Driving...................8-29
If Your Vehicle is Stuck in
Sand, Mud, Ice, or Snow. . .8-31
Rocking Your Vehicle to
Get It Out.......................8-31
Loading the Vehicle..........8-32
Fuel
Fuel..................................8-36
Gasoline Octane...............8-36
Gasoline Specications.....8-36
California Fuel..................8-36
Additives...........................8-37
Fuels in Foreign
Countries........................8-37
Filling the Tank.................8-38
Filling a Portable Fuel
Container........................8-40
Driving and Operating 8-1
2009 - Pontiac Vibe Owner Manual

Starting and
Operating Your
Vehicle
New Vehicle Break-In
Notice:The vehicle does
not need an elaborate break-in.
But it will perform better in
the long run if you follow
these guidelines:
Do not drive at any one
constant speed, fast or slow,
for the rst 500 miles (805 km).
Do not make full-throttle
starts. Avoid downshifting
to brake or slow the vehicle.
Avoid making hard stops for
the rst 200 miles (322 km) or
so. During this time the new
brake linings are not yet broken
in. Hard stops with new linings
can mean premature wear and
earlier replacement. Follow this
breaking-in guideline every
time you get new brake linings.
Do not tow a trailer during
break-in. SeeTowing a Trailer
on page 9-77for the trailer
towing capabilities of your
vehicle and more information.
Following break-in, engine speed
and load can be gradually
increased.
Ignition Positions
The ignition switch has four different
positions.
To shift out of P (Park), turn the
ignition to ON/RUN and apply
the brake pedal.
Notice:Using a tool to force the
key to turn in the ignition could
cause damage to the switch or
break the key. Use the correct key,
make sure it is all the way in, and
turn it only with your hand. If the
key cannot be turned by hand,
see your dealer/retailer.
8-2 Driving and Operating
2009 - Pontiac Vibe Owner Manual

LOCK/OFF:This is the only position
from which you can remove the key.
This locks the steering wheel,
ignition and automatic transmission.
Push in the ignition switch as you
turn the key toward you.
On vehicles with an automatic
transmission, the shift lever must be
in P (Park) to turn the ignition switch
to the LOCK/OFF position.
A warning tone will sound if the driver
door is opened with the key in the
ignition.
The ignition switch can bind in the
LOCK/OFF position with your wheels
turned off center. If this happens,
move the steering wheel from right
to left while turning the key to
ACC/ACCESSORY. If this doesn’t
work, then the vehicle needs service.{CAUTION
On manual transmission vehicles,
turning the key to LOCK/OFF and
removing it will lock the steering
column and result in a loss of
ability to steer the vehicle.
This could cause a collision.
If you need to turn the engine
off while the vehicle is moving,
turn the key only to ACC/
ACCESSORY. Do not push the
key in while the vehicle is moving.
ACC/ACCESSORY:This position
provides power to some of the
electrical accessories. It unlocks the
steering wheel and ignition. To move
the key from ACC/ACCESSORY to
LOCK/OFF, push in the key and then
turn it to LOCK/OFF.
A warning tone will sound when
the driver door is opened when the
ignition is still in ACC/ACCESSORY
or LOCK/OFF and the key is in the
ignition.ON/RUN:The ignition switch stays
in this position when the engine is
running. This position can be used to
operate the electrical accessories,
including the ventilation fan and
115 volt power outlet, as well as to
display some warning and indicator
lights. The transmission is also
unlocked in this position on
automatic transmission vehicles.
The battery could be drained
if you leave the key in the ACC/
ACCESSORY or ON/RUN position
with the engine off. You may not be
able to start the vehicle if the battery
is allowed to drain for an extended
period of time.
START:This position starts the
engine. When the engine starts,
release the key. The ignition switch
will return to ON/RUN for normal
driving.
Driving and Operating 8-3
2009 - Pontiac Vibe Owner Manual

Retained Accessory
Power (RAP)
These vehicle accessories may be
used for less than a minute after
the engine is turned off.
Power Windows, if equipped
Sunroof, if equipped
The power windows and sunroof
will continue to work for less than a
minute or until either front door is
opened. The radio will work when
the key is in ON/RUN or ACC/
ACCESSORY.
Starting the Engine
Automatic Transmission
Move the shift lever to P (Park) or
N (Neutral). The engine will not start
in any other position. To restart
when you are already moving,
use N (Neutral) only.
Notice:Shifting into P (Park)
with the vehicle moving could
damage the transmission.
Shift into P (Park) only when
your vehicle is stopped.
Manual Transmission
The shift lever should be in
NEUTRAL and the parking brake
engaged. Hold the clutch pedal
to the oor and start the engine.
The vehicle will not start if the clutch
pedal is not all the way down.
Starting Procedure
1. With your foot off the accelerator
pedal, turn the ignition to START.
When the engine starts, let go of
the key. The idle speed will go
down as the engine gets warm.
Vehicles equipped with
the 1.8L engine have a
Computer-Controlled Cranking
System. This feature assists in
starting the engine and protects
components. If the ignition key is
turned to the START position,
and then released when the
engine begins cranking, the
engine will continue cranking for
a about 30 seconds or until the
vehicle starts. If the engine doesnot start and the key is held in
START for many seconds,
cranking will be stopped after
25 seconds to prevent cranking
motor damage. To prevent gear
damage, this system also
prevents cranking if the engine is
already running. Engine cranking
can be stopped by turning
the ignition switch to ACC/
ACCESSORY or LOCK/OFF.
Vehicles equipped with the
2.4L engine should not be
cranked for more than
30 seconds at a time.
This may overheat the
starter and wiring systems.
Notice:Holding the key in
START for longer than 15 seconds
at a time will cause the battery to
be drained much sooner. And
the excessive heat can damage
the starter motor. Wait about
15 seconds between each try to
help avoid draining the battery
or damaging the starter.
8-4 Driving and Operating
2009 - Pontiac Vibe Owner Manual

2. If the engine does not start, wait
about 15 seconds and try again
to start the engine by turning
the ignition to START. Wait about
15 seconds between each try.
When the engine has run
about 10 seconds to warm up,
the vehicle is ready to be driven.
Do not run the engine at high
speed when it is cold.
If the weather is below freezing
(32°F or 0°C), let the engine run
for a few minutes to warm up.
3. If the engine still will not start, or
starts but then stops, it could be
ooded with too much gasoline.
Try pushing the accelerator pedal
all the way to the oor and holding
it there as you hold the key in
START for about three seconds.
If the vehicle starts briey but then
stops again, do the same thing,
but this time keep the pedal down
for ve or six seconds. This clears
the extra gasoline from the
engine.Notice:The engine is designed
to work with the electronics in
the vehicle. If electrical parts or
accessories are added, you could
change the way the engine
operates. Before adding electrical
equipment, check with your
dealer/retailer. If you do not,
the engine might not perform
properly. Any resulting damage
would not be covered by the
vehicle warranty.
Engine Coolant Heater
The engine coolant heater, if
available, can help in cold weather
conditions at or below 0°F (−18°C)
for easier starting and better fuel
economy during engine warm-up.
Plug in the coolant heater at least
four hours before starting the vehicle.
To Use the Engine Coolant
Heater
1. Turn off the engine.
2. Open the hood and unwrap the
electrical cord. The electrical
cord is located on the driver side
of the engine compartment.
3. Plug it into a normal, grounded
110-volt AC outlet.
{CAUTION
Plugging the cord into an
ungrounded outlet could cause
an electrical shock. Also, the
wrong kind of extension cord could
overheat and cause a re. You
could be seriously injured. Plug the
cord into a properly grounded
three-prong 110-volt AC outlet.
If the cord will not reach, use a
heavy-duty three-prong extension
cord rated for at least 15 amps.
Driving and Operating 8-5
2009 - Pontiac Vibe Owner Manual