2009 Peugeot 607 Dag rims

7
77
HORN
HAZARD WARNING LAMPS
Automatic lighting of hazard warning lights *
When braking in an emergency, de-
pending on the deceleration, the hazard
warning lights come on automatically.
They switch off automatically the fi rst
time you accelerate.
It is also possible to switch them off by
pressing the button.
* According to country.
Press one of the spokes of the steering
wheel.
Press the button, the direction indica-
tors fl ash.
They can operate with the ignition off.
ANTI-LOCK BRAKING SYSTEM
(ABS) AND ELECTRONIC
BRAKE FORCE DISTRIBUTION
(EBFD)
The ABS, in conjunction with the elec-
tronic brake force distribution, increas-
es the stability and manoeuvrability of
your vehicle on braking, in particular
on poor or slippery road surfaces.

Note: when changing wheels (tyres
and rims), make sure that these are
approved.
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
When this warning light
comes on, accompanied by
a buzzer and a message, it
indicates that there is a mal-
function of the ABS, which
can cause a loss of control of the vehi-
cle when braking. When this warning light
comes on, connected to
the
STOP and ABS warn-
ing lights, accompanied by
a buzzer and a message, it
indicates that there is a malfunction of
the electronic brake force distribution,
which can cause a loss of control of
the vehicle when braking.
Stop immediately.
In both cases, consult a PEUGEOT
dealer.
Normal operation of the ABS may
make itself felt by slight vibrations of
the brake pedal.
ASSISTANCE SYSTEM
In an emergency, this system enables
the optimum braking pressure to be
reached more quickly, thus reducing
the stopping distance.
It is triggered by the speed at which
the brake pedal is activated.
The effect of this is a reduction in the
resistance of the pedal and an in-
crease in braking effi ciency.
When braking in an emergency, press
fi rmly without releasing the pressure.
In emergency braking, press
very fi rmly without releas-
ing the pressure.

7
78
The switch lights up and the
warning light comes on: the
ASR and ESP systems no
longer have any effect on the
engine operation.
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to be
improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and that
required by the driver, the ESP system
automatically acts on the engine and
the brake of one or more wheels, in or-
der to put the vehicle back on course,
within the limits of the laws of physics.
Operation of the ASR and ESP
systems The warning light fl ashes
when the ASR or ESP is ac-
tivated. Disarming
Reactivation:

 Automatic if the ignition is switched
off.

 Automatic from 30 mph (50 km/h).

 Manual by pressing the switch
again. When a malfunction of the
systems occurs, the switch
light fl ashes and the warn-
ing light comes on, accom-
panied by an audible signal
and a message on the multi-function
display.
Contact a PEUGEOT dealer to have
the system checked.
The ASR/ESP systems offer
exceptional safety in normal
driving, but this should not en-
courage the driver to take extra
risks or drive at high speed.
The correct functioning of these sys-
tems depends on observation of the
manufacturer's recommendations re-
garding the wheels (tyres and rims), the
braking components and the electronic
components, as well as the PEUGEOT
assembly and operation procedures.
After an impact, have the system
checked by a PEUGEOT dealer.
When the ignition is on, the
ASR and ESP systems are
always activated. Operating check
Activation of the ASR and ESP
systems In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground), it may be ad-
visable to disarm the ASR and ESP
systems, so that the wheels can move
freely and regain grip.

 Press the "ESP OFF" switch, lo-
cated under the steering wheel to
the right.

1010
100
Access to the spare wheel and the
jack in the boot

 Detach the luggage net.

 Lift the boot carpet using the lifting
hook. Secure this hook behind the
boot seal.
CHANGING A WHEEL
Tools available
The following tools are located in the
polystyrene holder in the centre of the
spare wheel:

1. Wheelbrace.

2. Centralising tool.

3. Wheelbrace extension.

4. Jack.

5. Removable towing eye.

6. Alloy wheel trim remover.

7. Trim cover tool. Removal

 For vehicles with alloy wheels fi tted
with wheel trims, pull the centre trim
by using tool 6 in one of the holes.

 Loosen the wheel bolts.

 Take the jack 4 from the tool kit .

 Place the jack in one of the four
locations A underneath the vehicle
(the nearest one to the wheel to be
changed).

 Extend the jack using wheelbrace 1
and the extension 3 .

 Remove a wheel bolt at the top
and fi t the centralising tool 2 in its
place.

 Unscrew the other bolts and remove
the wheel.
Park the vehicle so that it does
not obstruct traffi c: the ground
must be level, stable and non-
slippery.
Apply the handbrake, switch off the igni-
tion and engage fi rst or reverse gear (po-
sition P for the automatic gearbox).
It is imperative to ensure that the occu-
pants get out of the vehicle and wait in
a safe location.
Never go underneath a vehicle which is
supported only by a jack; use a ramp.
The jack and all of the tools are specifi c
to your vehicle. Do not use them for other
purposes.

1010
101
Fitting a wheel
 Put the tool holder back in position.
This helps to keep the boot fl oor in its
correct position, to prevent any defor-
mation of the fl oor when loaded.

 Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. After changing the wheel:
- have the tightening of the bolts and
the tyre pressure checked by a
PEUGEOT dealer as soon as pos-
sible,
- have the punctured wheel repaired and refi t it to the vehicle as soon as
possible,
- the steel spare wheel must only be used for a very short time.

 Position the wheel using the cen-
tralising tool 2 to assist you.

 Tighten the bolts by hand and re-
move the centralising tool.

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 4 and remove it.

 Fully tighten the bolts using the
wheelbrace.

 Replace the wheel trim.

 For the alloy trims, position the re-
moval hole opposite the valve. Tyres fi tted with the Tyre
Under-Infl ation Detection System.
These wheels have a pressure sensor.
Have them repaired by a PEUGEOT
dealer.

1010
102
Special features of alloy wheels Fitting the spare wheel Anti-theft bolts
Fitting snow tyres
If you wish to fi t snow chains on your
vehicle, contact a PEUGEOT dealer
to fi nd out which models are recom-
mended for your vehicle.
Bolt covers
Alloy wheel bolts are covered by chrome
trims.
Use the yellow tool 7 to remove the
trims before slackening the bolts.
If your vehicle is fi tted with a steel spare
wheel, when fi tting it, it is
normal to no-
tice when tightening the bolts that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone-shape of each bolt. If your wheels are fi tted with an anti-theft
bolt (one per wheel), the chrome trim
must be removed using the yellow tool,
before unscrewing the bolt using the
anti-theft socket and the wheel brace.

Note: the anti-theft socket
was given to you on delivery
of your vehicle along with the
duplicate keys and the confi -
dential card.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.

1010
114
ACCESSORIES FOR YOUR 607
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the network.
They all benefi t from PEUGEOT's
recommendation.
These accessories and parts, having
been tested and approved for reliabil-
ity and safety, are all adapted to your
PEUGEOT vehicle.
The product range offered by PEUGEOT
Accessories is structured around 5 catego-
ries: PROTECTION - TOURING - IN-CAR
TECHNOLOGY - STYLING - UNIVERSAL.
The fi tting of electrical equipment or accessories which are not
recommended by PEUGEOT
may result in a failure of your
vehicle's electronic system.
Please note this specifi c warning. You
are advised to contact a representa-
tive of the Marque to be shown the
range of recommended equipment
and accessories.
"Protection":
parking assistance, anti-theft
alarm, stolen vehicles recov-
ery system * , engraved win-
dows, locking wheel nuts, fi rst
aid kit, warning triangle, high
visibility safety jacket, snow
chains. "Touring":
covers compatible with air
bag components, mats, boot
tray, luggage retaining net,
sill protectors.
For leisure pursuits: roof
bars, transportation accessories (bi-
cycle carrier, ski carrier), roof box,
child seats and booster cushions, rear
screen blind, audio/telephone console,
cool box.
Trailer towbar which must be fi tted by
the PEUGEOT network.
"In-Car Technology":
hands-free kits, satellite navi-
gation systems, CD changer,
DVD player, video screen.
You are advised to contact
a PEUGEOT dealer before
installing accessory radiocommunica-
tion transmitters with external aerial
on your vehicle.
Your PEUGEOT dealer will inform you
of the characteristics (frequency band,
maximum output power, aerial posi-
tion, specifi c installation conditions) of
the transmitters which can be fi tted,
in accordance with the Motor Vehicle
Electromagnetic Compatibility Direc-
tive (2004/104/EC). "Styling":
alloy wheels, wheel trims,
spoiler, leather gear lever
knob, styling strips, door spoil-
ers, sport exhaust.
"Universal":
windscreen wash fl uid, interi-
or and exterior cleaning and
maintenance products.
Depending on the country in
which the vehicle is sold, it is
compulsory to have a safety
jacket, warning triangle and
spare bulbs available in the
vehicle.

Wheels which are fi tted with
235/45 R 18 tyres cannot be fi tted
with snow chains. For further infor-
mation, contact a
PEUGEOT dealer. Note
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
and secured correctly,
- never fi t one mat on top of another.
* According to country.

11
119

A. Manufacturer's plate.

B. Serial number on the bodywork.

C. Serial number on the fascia.
D. Tyres.
Label D on the central door pillar on
the driver's side indicates:
- the dimensions of the rims and tyres,
- the makes of tyre recommended by the manufacturer, - the tyre pressures
(checking of
the tyre pressure must be car-
ried out when the tyres are cold,
at least once a month) ,
- the paint colour reference.
THE IDENTIFICATION FEATURES OF YOUR 607