2009 Peugeot 607 Dag display
[x] Cancel search: displayPage 29 of 182
1
30
INSTRUMENT PANEL DISPLAY
After switching on the ignition, two
functions are shown in succession:
- s e r v i c e i n d i c a t o r ,
- total distance recorder (total and trip distances).
Note: the total and trip distances are dis-
played for 30 seconds when the ignition
i s s w i t c h e d o f f , o n o p e n i n g t h e d r i v e r ' s
door, as well as on locking and unlock-
i n g t h e v e h i c l e .
Engine oil level indicator
When the ignition is switched on, the
e n g i n e o i l l e v e l i s i n d i c a t e d o n t h e
instrument panel display for approxi-
mately 7 seconds.
T h i s l e v e l i s i n d i c a t e d a t t h e s a m e
t i m e a s t h e s e r v i c e i n f o r m a t i o n w h i c h
appears on the display located in the
speedometer dial.
Oil level correct
Lack of oil
Flashing indicates a lack
of oil which may damage
the engine.
If the lack of oil is con-
fi r m e d b y c h e c k i n g u s i n g
t h e d i p s t i c k , i t i s i m p e r a t i v e t h a t t h e
l e v e l i s t o p p e d u p . C h e c k t h e o i l l e v e l u s i n g
the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e
fl a s h i n g i n d i c a t e s a n e n -
g i n e o i l l e v e l g a u g e m a l -
function.
Consult a PEUGEOT dealer.
T h e l e v e l o b s e r v e d o n t h e d i p s t i c k i s
o n l y v a l i d i f t h e v e h i c l e i s p a r k e d o n
l e v e l g r o u n d a n d t h e e n g i n e h a s b e e n
off for more than 15 minutes.
Dipstick
T h e r e a r e 2 l e v e l m a r k s o n t h e
dipstick:
- n e v e r e x c e e d l e v e l A ,
- i n p o s i t i o n B , t o p u p t h e l e v - e l v i a t h e o i l fi l l e r c a p , u s i n g
the type of oil suited to your
engine.
A = max.
B = min.
Oil level gauge fault
Page 30 of 182
1
31
SERVICE INDICATOR
T h i s i s a v i s u a l r e m i n d e r o f w h e n t h e
n e x t s e r v i c e i s d u e . T h i s s e r v i c e i s t o
be carried out according to the manu-
f a c t u r e r ' s s e r v i c i n g s c h e d u l e .
T h e p o i n t a t w h i c h t h e s e r v i c e i s d u e i s
calculated from the last indicator zero
reset. It is determined by two param-
eters:
- t h e d i s t a n c e t r a v e l l e d ,
- the time elapsed since the last s e r v i c e .
Note: the distance remaining before
t h e n e x t s e r v i c e i s d u e m a y b e w e i g h t -
ed by the time factor.
T h e s e r v i c e i n f o r m a t i o n a p p e a r s o n
the display, located in the speedo-me-
ter dial, at the same time as the en-
g i n e o i l l e v e l o n t h e i n s t r u m e n t p a n e l
display.
Operation
As soon as the ignition is switched on
and for 7 seconds, the spanner sym-
b o l i s i n g t h e s e r v i c i n g o p e r a t i o n s i s l i t .
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
b e f o r e t h e n e x t s e r v i c e .
Example: 4 , 8 0 0 m i l e s / k m r e m a i n b e -
f o r e t h e n e x t s e r v i c e i s d u e . W h e n t h e
ignition comes on and for 7 seconds
the display indicates:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the display
shows the total and trip distances.
The distance remaining before the
next service is less than 500 miles
(1,000 km).
Each time the ignition is switched on
and for 7 seconds, the spanner and
t h e d i s t a n c e fl a s h .
Example: 900 miles/km remain before
t h e n e x t s e r v i c e i s d u e .
When switching on the ignition and for
7 seconds, the display shows:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit.
T h i s i n d i c a t e s t h a t a s e r v i c e s h o u l d b e
carried out shortly. The display shows
the total and trip distances.
Page 31 of 182
1
32
Trip recorder zero reset button
Lighting rheostat button
With the ignition on, press the button
until the zeros appear.
With the headlamps on, press button B to
increase the brightness of the lighting of
the instruments and controls or button A to
reduce it.
As soon as the lighting reaches the required
l e v e l o f b r i g h t n e s s , r e l e a s e t h e b u t t o n .
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit. The display shows the total
and trip distances.
Note: the spanner may also be lit if the
t w o - y e a r i n t e r v a l h a s b e e n e x c e e d e d .
Service indicator zero re-set
The service is overdue.
Each time the ignition is switched on
and for 7 seconds, the spanner and
t h e e x c e s s d i s t a n c e fl a s h .
Example: t h e s e r v i c e i s o v e r d u e b y
3 0 0 m i l e s / k m . T h e s e r v i c e s h o u l d b e
c a r r i e d o u t v e r y s h o r t l y .
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
o p e r a t i o n a f t e r e a c h s e r v i c e .
H o w e v e r , i f y o u c a r r y o u t t h e s e r v i c e
yourself, the re-set procedure is as fol-
lows:
Switch off the ignition,
Press and hold the trip recorder re-
set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you wish
to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t
fi v e m i n u t e s , o t h e r w i s e t h e z e r o
re-set will not be registered.
Page 32 of 182
1
32
Trip recorder zero reset button
Lighting rheostat button
With the ignition on, press the button
until the zeros appear.
With the headlamps on, press button B to
increase the brightness of the lighting of
the instruments and controls or button A to
reduce it.
As soon as the lighting reaches the required
l e v e l o f b r i g h t n e s s , r e l e a s e t h e b u t t o n .
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit. The display shows the total
and trip distances.
Note: the spanner may also be lit if the
t w o - y e a r i n t e r v a l h a s b e e n e x c e e d e d .
Service indicator zero re-set
The service is overdue.
Each time the ignition is switched on
and for 7 seconds, the spanner and
t h e e x c e s s d i s t a n c e fl a s h .
Example: t h e s e r v i c e i s o v e r d u e b y
3 0 0 m i l e s / k m . T h e s e r v i c e s h o u l d b e
c a r r i e d o u t v e r y s h o r t l y .
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
o p e r a t i o n a f t e r e a c h s e r v i c e .
H o w e v e r , i f y o u c a r r y o u t t h e s e r v i c e
yourself, the re-set procedure is as fol-
lows:
Switch off the ignition,
Press and hold the trip recorder re-
set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you wish
to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t
fi v e m i n u t e s , o t h e r w i s e t h e z e r o
re-set will not be registered.
Page 33 of 182
1
33
TRIP COMPUTER
Each press on the button, located at the
end of the wipers stalk , displays differ-
ent trip computer data in succession:
Colour and map screen DT
- the "Current info" with:
Page 34 of 182
1
34
Distance travelled (km or miles)
T h i s i n d i c a t e s t h e d i s t a n c e t r a v e l l e d
since the computer was last set to
zero.
Distance remaining to be travelled (km or miles)
This is the distance remaining to be
t r a v e l l e d t o t h e fi n a l d e s t i n a t i o n . I t i s
e i t h e r c a l c u l a t e d b y t h e n a v i g a t i o n
s y s t e m i f g u i d a n c e i s a c t i v a t e d o r e n -
tered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed (km/h or mph)
T h i s i s t h e a v e r a g e s p e e d c a l c u l a t e d
since the computer was last set to
zero (with the ignition on). The routes
"1" and "2" are independ-
e n t b u t h a v e i d e n t i c a l a p p l i c a t i o n .
Route "1" for example allows you to
make daily calculations and route "2"
monthly calculations.
The routes
Zero reset
When the required route is displayed,
press the end of the wipers stalk for
more than two seconds.
Access via the general menu
DT screen
"TRIP" menu
Press the "MENU" or "TRIP" button
to gain access to the general menu.
Select the "Trip computer" applica-
t i o n u s i n g t h e n a v i g a t o r , t h e n c o n fi r m .
T h e " T r i p c o m p u t e r " m e n u o f f e r s v a r i o u s
options:
- Inputting of the distance to be t r a v e l l e d ,
- Warnings log,
- Status of the functions.
Page 35 of 182
1
35
Warnings log
T h i s s u m m a r i s e s t h e a c t i v e w a r n i n g
messages, displaying them on the
multifunction display in succession.
Status of the functions
T h i s s u m m a r i s e s t h e a c t i v e o r i n a c t i v e
status of the functions present on the
v e h i c l e .
Inputting the distance remaining to
be travelled
W h e n g u i d a n c e i s n o t a c t i v a t e d , t h i s
enables you to enter an approximate
d i s t a n c e t o t h e fi n a l d e s t i n a t i o n . The different trip computer data also
appears on the instrument panel dis-
play at the same time. panel display
Page 36 of 182
2
36
DT COLOUR AND MAP
SCREEN
This displays the following informa-
tion, via the PC Com control pad:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k
of ice),
- t h e a c c e s s e s c h e c k ,
- the vehicle functions warning or status messages, displayed tem-
porarily,
- the audio sources displays,
- the telematic systems displays (telephone, services, ...),
- the trip computer displays,
- t h e c o n fi g u r a t i o n d i s p l a y s ,
- the satellite navigation system dis- plays. Management of the displays
The
"AUDIO" , "NAV" , "TRIP" and
"TEL" buttons on the PC Com control
pad permit displaying in the main win-
dow. E x a m p l e : " C o n fi g u r a t i o n "
" C o n fi g u r a t i o n " m e n u
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
G e n e r a l m e n u
Press the
"MENU" button to gain
access to the g e n e r a l m e n u and
select one of the following functions:
- "Navigation-Guidance",
- "Audio functions",
- "Trip computer",
- " C o n fi g u r a t i o n " ,
- "Directory",
- "Telematics",
- "Map",
- "Video". This provides access to successive
c o n fi r m a t i o n w i n d o w s .
Example: "TRIP"