2009 Peugeot 407 ESP
[x] Cancel search: ESPPage 119 of 250
8DRIVING
101
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
Flat tyre Instrument panel display
warning light.
This is accompanied by the audible signal
and the message on the multi-function
display locating the wheel concerned.
If this warning light comes on, have
the tyre pressure checked as soon as
possible.
Puncture
This warning light, accompanied by
the audible signal and the message on
the multi-function display locating the
wheel concerned, is followed by illumi-
nation of the "STOP" warning light. Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
t u r e d o r v e r y d e fl a t e d t y r e ) , a n d h a v e
the tyre pressure checked as soon as
possible.
Sensor(s) not detected or faulty
Instrument panel display
warning light. All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system
reinitialised by a PEUGEOT dealer.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate
the need to have the tyre pressure
checked regularly (see manufacturer's
label on the door pillar) to ensure that
the optimum dynamic performance
of the vehicle is maintained and pre-
vent premature wear of the tyres, par-
ticularly in arduous driving conditions
(heavy load, high speed).
The tyre pressures must be checked
cold, at least once a month. Remem-
ber to check the pressure of the spare
wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem may experience temporary inter-
ference due to radioelectric emissions
on a frequency close to that used by
the system.
Note : this message is also
displayed when one of the
wheels is away from the ve-
hicle (being repaired) or when
one or more wheels without a
s e n s o r a r e fi t t e d .
Instrument panel display
warning light.
This is accompanied by the audible
signal and the message on the multi-
function display which indicates that
u n d e r - i n fl a t i o n d e t e c t i o n i s a b s e n t
from one (or several) wheel(s) or that
there is a fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
Page 128 of 250
9CHECKS
111
CHECKS
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
H a v e t h e fi l t e r e l e m e n t s
replaced regularly. If you drive
in dusty conditions, change
them twice as often.
Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is imperative that the particle emis-
s i o n fi l t e r i s m a i n t a i n e d i n a c c o r d a n c e
with the manufacturer’s servicing
schedule, by a PEUGEOT dealer.
Note: following prolonged operation of
the vehicle at very low speed or at idle,
y o u m a y , i n e x c e p t i o n a l c i r c u m s t a n c e s ,
notice emissions of water vapour at the
e x h a u s t o n a c c e l e r a t i o n . T h i s d o e s n o t
have any effect on the performance of
the vehicle or the environment.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n a s -
sembly may operate after the vehicle
has stopped, even when the engine is
cold. Where the handbrake travel is
too great or there is a reduc-
tion in the performance of the
system, the handbrake should
be adjusted.
Have the system checked by a
PEUGEOT dealer.
Handbrake
Disc wear status
For any information relating to checking
disc wear, contact a PEUGEOT dealer.
FUEL SUPPLY CUT-OFF
(PETROL) *
As a safety precaution, in certain circum-stances, a mechanism prevents fuel from reaching the engine. To re-establish the fuel supply:
RUNNING OUT OF FUEL (DIESEL)
If you should run out of fuel, it is neces-
sary to re-prime the circuit.
The repriming pump and the degas
screw are located under the bonnet
(see corresponding illustration in the
t e c h n i c a l d a t a s e c t i o n ) :
1.6 litre 16V HDI engine
- fi l l t h e f u e l t a n k w i t h a t l e a s t fi v e
litres of diesel,
- squeeze and release the manual re-priming pump, until fuel appears
in the transparent pipe,
- operate the starter until the engine starts.
2 litre 16V HDI engine
- fi l l t h e f u e l t a n k w i t h a t l e a s t fi v e litres of diesel,
- unscrew the degas screw,
- squeeze and release the manual repriming pump until diesel is seen
escaping via the degas screw,
- retighten the degas screw,
- operate the starter until the engine starts.
Brake pad wear depends on
the style of driving, in particu-
lar for vehicles which are used
in town, over short distances.
Brake pads It may be necessary to check
the thickness of the pads,
even between services.
* According to version.
To ensure the best perfor-
mance from components as
important as the power steer-
ing and the braking system, the
m a n u f a c t u r e r s e l e c t s a n d o f f e r s s p e c i fi c
products, only use products recom-
mended by PEUGEOT .
Battery
To prevent damage to the electrical units,
high pressure washing of the engine
compartment is strictly prohibited .
press the red button on the angle of the front right-hand suspension assembly, under the bonnet.
Page 129 of 250
1010PRACTICAL INFORMATION
112
CHANGING A WHEEL
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:
1. Wheelbrace.
Permits removal of the wheel trim and removal of the wheel securing
bolts.
2. Jack with integrated handle.
Permits raising of the vehicle.
3. Removable towing eye.
See corresponding section.
4. Bolt cover tool.
Permits removal of the bolt protectors (covers) on alloy wheels. Removal
For vehicles with steel wheels,
detach the trim using the wheel-
brace 1 pulling at the valve pas-
sage hole.
For vehicles with alloy wheels,
remove the covers using tool 4 .
Loosen the wheel bolts.
Take the jack from the tool kit.
Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).
Extend the jack 2 until its base is in
contact with the ground.
Unscrew the bolts and remove the
wheel.
Access to the spare wheel and the
jack in the boot
L i f t t h e fl o o r u s i n g t h e l i f t i n g h a n d l e .
Secure the handle behind the boot
seal. Never go underneath a vehicle
which is supported only by a
jack.
Park the vehicle on level, stable
and non-slippery ground.
Apply the handbrake, switch off the
i g n i t i o n a n d e n g a g e fi r s t o r r e v e r s e
gear (position P for the automatic
gearbox).
Page 133 of 250
1010PRACTICAL INFORMATION
115
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55 W.
Remove the protective cover cor-
responding to the faulty bulb.
Disconnect the connector.
Press the end of the securing clips
to free the bulb. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e t h a t
the direction notches are positioned
correctly and the securing clips are
fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
4 -
Direction indicators:
PY 21 W (amber).
Turn the bulb holder a quarter turn
and remove it.
Change the bulb.
WARNING: RISK OF
ELECTROCUTION
Front lights
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam headlamps:
H1-55 W or D2S-35 W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direction
indicators and side repeaters)
must be replaced with bulbs
o f i d e n t i c a l s p e c i fi c a t i o n a n d
colour.
5 - Front fog lamps: H11 - 55 W.
Turn the wheels to full lock.
A c c e s s t o t h e b u l b i s v i a t h e fl a p i n t h e
f r o n t m u d fl a p .
Consult a PEUGEOT dealer.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality.
High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the lights and their periphery to avoid
damaging their coating and their seal.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lights are switched on.
3 - Side lights: W 5 W.
Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
Put the connector back in place.
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
Page 136 of 250
1010PRACTICAL INFORMATION
117
CHANGING A REAR BULB (407 SW)
Left and right fog lamps:
P21 W.
Carefully unclip the tailgate interior
trim.
Detach the sealing sheet located
behind the light concerned.
Remove the bulb holder turning it a
quarter of a turn.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e b u l b i s
positioned correctly in the bulb holder.
Unclip the light (2 clips).
Disconnect the connector and re-
move the light.
Unclip the bulb holder moving
aside the 4 tabs.
Unscrew the bulb and change it.
Reconnect the connector.
Lock the bulb holder in place.
W h e n r e fi t t i n g i t , e n s u r e t h a t t h e
lamp is correctly positioned and
secured, reclipping the rear part
then the front part.
Number plate lights:
W 5 W.
Insert a thin screwdriver in one of
the exterior holes of the transpar-
ent cover.
Push it towards the outside to un-
clip it.
Remove the transparent cover.
Change the faulty bulb. Third brake light (diodes)
All work on the diode lights must be
carried out by a PEUGEOT dealer.
Wing lights
1. Brake lights/side lights:
P21/5 W.
2. Reversing lights:
P21 W.
3. Direction indicators:
P21 W.
These three bulbs are changed by
removing the light.
Remove the corresponding boot
s i d e fl a p t o g a i n a c c e s s t o t h e
light.
R e m o v e t h e l i g h t fi x i n g n u t i n s i d e
the boot.
Note: if necessary, use the wheelbrace
to remove the nuts. In some climatic conditions
(e.g. low temperature or hu-
midity), the presence of misting
on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Page 137 of 250
1010PRACTICAL INFORMATION
118
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi e d . T h e f u s e n u m b e r s a r e i n d i c a t e d
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating
A
Functions
F1 15 Rear wiper.
F2 30 Central locking/deadlocking.
F3 5 Air bags.
F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.
F5 30 Front one-touch electric windows, sunroof
( S a l o o n ) , p a n o r a m i c r o o f c o n c e a l i n g fl a p
(407SW).
F6 30 Rear one-touch electric windows.
F7 5 Glove box light, side repeaters, front and rear
courtesy lights, map reading lights, courtesy
mirror.
F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control
unit, navigation-telematics (according to
country).
Page 138 of 250
1010PRACTICAL INFORMATION
118
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi e d . T h e f u s e n u m b e r s a r e i n d i c a t e d
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating
A
Functions
F1 15 Rear wiper.
F2 30 Central locking/deadlocking.
F3 5 Air bags.
F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.
F5 30 Front one-touch electric windows, sunroof
( S a l o o n ) , p a n o r a m i c r o o f c o n c e a l i n g fl a p
(407SW).
F6 30 Rear one-touch electric windows.
F7 5 Glove box light, side repeaters, front and rear
courtesy lights, map reading lights, courtesy
mirror.
F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control
unit, navigation-telematics (according to
country).
Page 141 of 250
1010PRACTICAL INFORMATION
122
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installa-
tion of accessories not supplied and
not recommended by PEUGEOT and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the ad-
ditional equipment connected exceeds
10 milliamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl a t b a t t e r y p r e v e n t s t h e
engine from starting.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer. If the telephone is being used
when economy mode starts,
i t w i l l s t i l l b e p o s s i b l e t o fi n i s h
the call.
Placing the wiper blades in the
maintenance position
Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. T h i s p e r i o d m a y b e s i g n i fi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.