2009 Peugeot 407 battery
[x] Cancel search: batteryPage 21 of 250
1INSTRUMENTS and CONTROLS
22
Battery charge warning
light
When the engine is running, this in-
dicates a charging circuit malfunction
(battery terminals, alternator belt).
Consult a PEUGEOT dealer. T y r e u n d e r - i n fl a t i o n w a r n i n g
light
This indicates that the tyre pressure is
too low.
A message on the multifunction display
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lights Activation warning light
Operation warning light
Deactivation warning light
Malfunction warning light
Power steering warning
light
This indicates a power steering fault.
It is linked with the STOP warning
light.
Consult a PEUGEOT dealer. Handbrake warning light
This indicates that the handbrake is
still applied or has not been released
correctly.
It is linked with the braking system
warning light. Low wash-wipe and
h e a d l a m p w a s h fl u i d l e v e l
warning light
When the wipers are switched on, this
i n d i c a t e s t h a t t h e fl u i d l e v e l i s t o o l o w .
Fill the wash-wipe and headlamp wash
fl u i d r e s e r v o i r .
Engine oil level warning
light
This indicates a critical engine oil level
(too low).
WARNING LIGHTS ON THE INSTRUMENT PANEL DISPLAY
These warning lights are displayed on
the instrument panel display.
STOP warning light
When this is displayed alone, it indi-
cates a power steering fault.
It comes on linked with the engine oil
pressure, coolant temperature, brak-
ing system or punctured tyre warning
lights.
Stop immediately.
Consult a PEUGEOT dealer.
Punctured tyre warning light
This indicates that one or more punc-
tured tyres have been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Consult a PEUGEOT dealer.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Page 25 of 250
1INSTRUMENTS and CONTROLS
26
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule. Service indicator zero reset
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the reset procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
reset button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears .
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time the
ignition is switched on and for 5 seconds,
t h e d i s t a n c e a n d t h e s p a n n e r fl a s h .
Example
: when the ignition is switched
on and for 5 seconds, the display
indicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal
operation and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be weighted
by the time factor, depending on the
user’s driving habits.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising the service operations is
lit. The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example
: when switching on the
ignition and for 5 seconds, the dis-
play shows that 900 miles/km remain
before the next service is due.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
l e a s t fi v e m i n u t e s , o t h e r w i s e
the zero reset will not be
registered.
Page 47 of 250
3COMFORT
47
A l w a y s s w i t c h o f f t h e p r o g r a m m a b l e
h e a t i n g w h i l e fi l l i n g w i t h f u e l t o a v o i d
a n y r i s k o f fi r e o r e x p l o s i o n .
T o a v o i d a n y r i s k o f p o i s o n i n g a n d
a s p h y x i a t i o n , t h e p r o g r a m m a b l e h e a t -
ing must not be used, even for short
p e r i o d s , i n a n e n c l o s e d s p a c e s u c h
a s a g a r a g e o r w o r k s h o p w h i c h i s n o t
e q u i p p e d w i t h a n e x h a u s t g a s e x t r a c -
t i o n s y s t e m .
D o n o t p a r k t h e v e h i c l e o n a n i n fl a m -
m a b l e s u r f a c e ( d r y g r a s s , d e a d l e a v e s ,
p a p e r … ) , t h e r e i s a r i s k o f fi r e .
T h e p r o g r a m m a b l e h e a t i n g s y s t e m
i s s u p p l i e d b y t h e v e h i c l e ' s f u e l t a n k .
B e f o r e u s e , e n s u r e t h a t t h e q u a n t i t y
o f f u e l r e m a i n i n g i s s u f fi c i e n t . I f t h e
f u e l t a n k i s a t t h e r e s e r v e , w e s t r o n g l y
a d v i s e t h a t y o u d o n o t p r o g r a m m e t h e
h e a t i n g .
Changing the battery
T h e r e m o t e c o n t r o l i s s u p p l i e d b y a
6 V - 2 8 L b a t t e r y , w h i c h i s s u p p l i e d .
I n f o r m a t i o n o n t h e d i s p l a y i n d i c a t e s
w h e n i t i s t i m e t o r e p l a c e t h i s b a t t e r y .
U n c l i p t h e c a s i n g t h e n r e p l a c e t h e
b a t t e r y .
The remote control must then be
r e i n i t i a l i s e d , s e e b e l o w .
A s a n a c c e s s o r y , y o u r p r o -
grammable heating can be
a d a p t e d t o p r e - h e a t y o u r v e h i -
c l e ' s p a s s e n g e r c o m p a r t m e n t .
Reinitialising the remote control
I f t h e v e h i c l e ' s b a t t e r y i s d i s c o n n e c t -
e d o r t h e r e m o t e c o n t r o l ' s b a t t e r y i s
r e p l a c e d , t h e r e m o t e c o n t r o l m u s t b e
r e i n i t i a l i s e d .
A f t e r s w i t c h i n g o n t h e p o w e r , p r e s s
button
4 ( O F F ) f o r 1 s e c o n d w i t h i n t h e
n e x t 5 s e c o n d s . I f t h e o p e r a t i o n h a s
t a k e n p l a c e c o r r e c t l y t h e m e s s a g e
"OK" i s d i s p l a y e d o n t h e r e m o t e c o n t r o l
s c r e e n .
I f a p r o b l e m o c c u r s , t h e m e s s a g e
"FAIL" a p p e a r s . R e p e a t t h e o p e r a t i o n . Do not discard the used
batteries, take them to an
a p p r o v e d c o l l e c t i o n p o i n t .
Page 67 of 250
4ACCESS
64
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
P r e s s t h e r e m o t e c o n t r o l l o c k i n g b u t -
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
r e - p r o g r a m m e t h e r e m o t e c o n t r o l .
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator light It is accompanied by a message on
t h e m u l t i - f u n c t i o n d i s p l a y .
Your vehicle will not start.
Consult a PEUGEOT dealer.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
T a k e t h e m t o a n a p p r o v e d c o l -
lection point. T h i s l o c k s t h e e n g i n e c o n t r o l s y s -
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correctly, the following indicator light comes on: If the keys are lost
V i s i t a P E U G E O T d e a l e r w i t h t h e v e -
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n .
T h e P E U G E O T n e t w o r k w i l l b e a b l e t o r e -
trieve the key code and the transponder
code to order a replacement key.
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote control
is a sensitive system; do not ope-
rate it while it is in your pocket as
there is a possibility that it may un-
lock your vehicle, without you being
aware of it.
The remote control does not ope-
rate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Page 70 of 250
4ACCESS
64
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
P r e s s t h e r e m o t e c o n t r o l l o c k i n g b u t -
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
r e - p r o g r a m m e t h e r e m o t e c o n t r o l .
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator light It is accompanied by a message on
t h e m u l t i - f u n c t i o n d i s p l a y .
Your vehicle will not start.
Consult a PEUGEOT dealer.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
T a k e t h e m t o a n a p p r o v e d c o l -
lection point. T h i s l o c k s t h e e n g i n e c o n t r o l s y s -
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correctly, the following indicator light comes on: If the keys are lost
V i s i t a P E U G E O T d e a l e r w i t h t h e v e -
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n .
T h e P E U G E O T n e t w o r k w i l l b e a b l e t o r e -
trieve the key code and the transponder
code to order a replacement key.
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote control
is a sensitive system; do not ope-
rate it while it is in your pocket as
there is a possibility that it may un-
lock your vehicle, without you being
aware of it.
The remote control does not ope-
rate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Page 71 of 250
4ACCESS
64
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
P r e s s t h e r e m o t e c o n t r o l l o c k i n g b u t -
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
r e - p r o g r a m m e t h e r e m o t e c o n t r o l .
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator light It is accompanied by a message on
t h e m u l t i - f u n c t i o n d i s p l a y .
Your vehicle will not start.
Consult a PEUGEOT dealer.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
T a k e t h e m t o a n a p p r o v e d c o l -
lection point. T h i s l o c k s t h e e n g i n e c o n t r o l s y s -
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correctly, the following indicator light comes on: If the keys are lost
V i s i t a P E U G E O T d e a l e r w i t h t h e v e -
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n .
T h e P E U G E O T n e t w o r k w i l l b e a b l e t o r e -
trieve the key code and the transponder
code to order a replacement key.
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote control
is a sensitive system; do not ope-
rate it while it is in your pocket as
there is a possibility that it may un-
lock your vehicle, without you being
aware of it.
The remote control does not ope-
rate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Page 79 of 250
4ACCESS
70
Notes:
After reconnecting the battery, you must
r e i n i t i a l i s e t h e s a f e t y a u t o - r e v e r s e :
- p l a c e t h e c o n t r o l i n t h e m a x i m u m partial opening position (3rd notch
to the right),
- w a i t u n t i l t h e r o o f i s i n t h e m a x i - mum partially open position,
- p r e s s t h e c o n t r o l f o r a t l e a s t o n e second.
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), and immediately after
the roof stops:
- m o v e t h e c o n t r o l t o t h e " O " p o s i t i o n and press the control immediately,
- c o n t i n u e t o p r e s s t h e c o n t r o l u n t i l the roof is fully closed. SUNROOF (SALOON) Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the roof, you must reverse
the movement of the roof. To do this,
press the switch concerned.
When the driver operates the roof
switch, he must ensure that no one is
preventing correct closing of the roof.
T h e d r i v e r m u s t e n s u r e t h a t t h e p a s -
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
- T o p a r t i a l l y o p e n t h e r o o f : T u r n t h e switch to the right (three possible
settings).
- T o o p e n t h e r o o f c o m p l e t e l y : T u r n the switch to the left (six possible
settings).
- T o c l o s e i t c o m p l e t e l y : T u r n t h e switch back to position "O".
- S a f e t y a u t o - r e v e r s e : W h e n t h e sunroof is closing and meets an
obstacle, it stops then partially
opens again.
The sunroof shutter is manual.
Page 80 of 250
4ACCESS
71
Safety auto-reverse
If the shutter encounters an obstacle
during closing, it stops and partially
opens again.
Y o u m u s t r e i n i t i a l i s e t h e s a f e t y a u t o -
r e v e r s e w i t h i n a m a x i m u m o f fi v e s e -
conds after the concealing shutter has
stopped:
- p r e s s p a r t A of the control until the
shutter is completely closed (closing
in stages of a few centimetres). PANORAMIC ROOF (407 SW) In the event of contact during
operation of the shutter, you
must reverse its movement.
To do this, press the control
concerned.
When the driver operates the shutter
control, he must ensure that no one
is preventing the shutter from closing
correctly.
T h e d r i v e r m u s t e n s u r e t h a t t h e p a s -
sengers use the concealing shutter
correctly.
P a y a t t e n t i o n t o c h i l d r e n d u r i n g o p e r a -
tion of the shutter.
Notes
:
Following reconnection of the battery,
in the event of a shutter malfunction
while it is moving or immediately after
it has stopped, you must reinitialise
t h e s a f e t y a u t o - r e v e r s e :
- p l a c e t h e c o n t r o l i n t h e f u l l y o p e n position (position "0"),
- w a i t u n t i l t h e s h u t t e r i s i n t h e f u l l y open position,
- p r e s s s e c t i o n A of the control for at
least three seconds.
In the event of unwanted opening of
the shutter on closing, and immediately
after the shutter has stopped:
- m o v e t h e c o n t r o l t o t h e f u l l y c l o s e d position (9th setting to the left) then
press part A of the control straight
away,
- c o n t i n u e t o p r e s s t h e c o n t r o l u n t i l the shutter is fully closed.
The safety auto-reverse function is
not active during these operations.
Y o u r v e h i c l e i s fi t t e d w i t h a t i n t e d g l a s s
panoramic roof which increases the
l i g h t a n d v i s i b i l i t y i n t h e p a s s e n g e r c o m -
partment. Its electric concealing shutter
improves temperature conditions.
The concealing shutter is controlled
electrically by a dial with nine opening
positions.
To close: turn the dial to the left (nine
possible settings).
To open: return the dial to the initial
position "0" .